Re: [PATCH] spi: spi-ti-qspi: clear wlen field while setting word length.

From: Vignesh R
Date: Mon Jul 11 2016 - 05:15:19 EST




On Monday 11 July 2016 02:39 PM, prahlad venkata wrote:
> On Mon, Jul 11, 2016 at 2:36 PM, prahlad venkata <prahlad.eee@xxxxxxxxx> wrote:
>> On Mon, Jul 11, 2016 at 2:14 PM, Vignesh R <vigneshr@xxxxxx> wrote:
>>>
>>>
>>> On Monday 11 July 2016 01:34 PM, prahlad venkata wrote:
>>>> On Mon, Jul 11, 2016 at 10:37 AM, Vignesh R <vigneshr@xxxxxx> wrote:
>>>>> Hi Prahlad,
>>>>>
>>>>> On Sunday 10 July 2016 01:35 AM, Prahlad V wrote:
>>>>>> When a word length of 1 byte is selected and writing data of length
>>>>>> more than QSPI_WLEN_MAX_BYTES, first MAX_BYTES will be transfered
>>>>>> and remaining will be transfered byte by byte. In that case wlen
>>>>>> field should be cleared before setting.
>>>>>>
>>>>>> Signed-off-by: Prahlad V <prahlad.eee@xxxxxxxxx>
>>>>>> ---
>>>>>> drivers/spi/spi-ti-qspi.c | 4 ++--
>>>>>> 1 file changed, 2 insertions(+), 2 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/spi/spi-ti-qspi.c b/drivers/spi/spi-ti-qspi.c
>>>>>> index 29ea8d2..6c61f54 100644
>>>>>> --- a/drivers/spi/spi-ti-qspi.c
>>>>>> +++ b/drivers/spi/spi-ti-qspi.c
>>>>>> @@ -276,9 +276,9 @@ static int qspi_write_msg(struct ti_qspi *qspi, struct spi_transfer *t,
>>>>>> cmd |= QSPI_WLEN(QSPI_WLEN_MAX_BITS);
>>>>>> } else {
>>>>>> writeb(*txbuf, qspi->base + QSPI_SPI_DATA_REG);
>>>>>> - cmd = qspi->cmd | QSPI_WR_SNGL;
>>>
>>> This is wrong. Deleting this line means QSPI_WR_SNGL is not set and no
>>> data is sent out on the wire.
>> QSPI_WR_SNGL is already set as soon as we enter the function.
>>>
>>>>>
>>>>> qspi->cmd always has WLEN field cleared and set to WLEN = 1 byte (see
>>>>> ti_qspi_start_transfer_one()). And hence variable 'cmd' will also have
>>>>> WLEN set to 1 byte.
>>>> Even though WLEN=1 is set in the ti_qspi_transfer_one, if we ask for a
>>>> transfer of large data,
>>>> say 300 bytes in length, for attaining faster data rate WLEN 128 is
>>>> selected for the first two
>>>> transactions and remaining 44 bytes will be transmitted with WLEN 1.
>>>> During that case,
>>>> WLEN will be changed inside qspi_write_msg function itself and the
>>>> field should be cleared
>>>> first while doing that.
>>>
>>> In qspi_write_msg(), qspi->cmd will always have WLEN set to
>>> QSPI_WLEN(t->bits_per_word) and qspi->cmd is never changed within this
>>> function.
>>> It is the value of local variable 'cmd' that is changed to appropriate
>>> WLEN (128bit or 8bit) as necessary.

> 'cmd' is written back to qspi->cmd for every transaction.

You mean qspi->cmd = cmd ?
I don't see this happening anywhere in the driver. Can you point me to
that line of code?

--
Regards
Vignesh