Re: [PATCH 3/3] ARM: dts: imx6sx-udoo-neo: Add SD

[Shawn Guo]

On Tue, Jul 05, 2016 at 06:04:10AM +0200, Andreas Färber wrote:
> Enable the SDHC node and model the SDIO_PWR GPIO as a regulator.
> Use the SD card as default trigger for the red LED.
> 
> Cc: Ettore Chimenti <ettore.chimenti@xxxxxxxx>
> Signed-off-by: Andreas Färber <afaerber@xxxxxxx>
> ---
>  
> 
>  arch/arm/boot/dts/imx6sx-udoo-neo.dtsi | 34 ++++++++++++++++++++++++++++++++++
>  1 file changed, 34 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> index e074409644d8..85f5e8606dab 100644
> --- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> +++ b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
> @@ -56,6 +56,7 @@
>  			label = "udoo-neo:red:mmc";
>  			gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>;
>  			default-state = "off";
> +			linux,default-trigger = "mmc0";
>  		};
>  
>  		orange {
> @@ -64,6 +65,17 @@
>  			default-state = "keep";
>  		};
>  	};
> +
> +	sdio_pwr_reg: sd-gpio-regulator {
> +		compatible = "regulator-fixed";
> +		gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +		regulator-name = "SDIO_PWR";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};

Is it correct to model SDIO power control GPIO as a boot-on and
always-on fixed regulator?  It will be powered-on even when SDIO driver
is not enabled or loaded.

Shawn

>  };
>  
>  &cpu0 {
> @@ -230,6 +242,17 @@
>  				<MX6SX_PAD_CSI_DATA06__UART6_RTS_B	0x1b0b1>,
>  				<MX6SX_PAD_CSI_DATA07__UART6_CTS_B	0x1b0b1>;
>  		};
> +
> +		pinctrl_usdhc2: usdhc2grp {
> +			fsl,pins =
> +				<MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059>,
> +				<MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059>,
> +				<MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059>,
> +				<MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059>,
> +				<MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059>,
> +				<MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059>,
> +				<MX6SX_PAD_SD1_DATA0__GPIO6_IO_2	0x17059>; /* CD */
> +		};
>  	};
>  };
>  
> @@ -259,3 +282,14 @@
>  	uart-has-rtscts;
>  	status = "disabled";
>  };
> +
> +&usdhc2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc2>;
> +	bus-width = <4>;
> +	cd-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>;
> +	no-1-8-v;
> +	keep-power-in-suspend;
> +	wakeup-source;
> +	status = "okay";
> +};
> -- 
> 2.6.6
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel