Re: c6x linker issue on linux-next-20160808 + some linker table work

[Mark Salter]

On Tue, 2016-08-09 at 20:40 +0200, Luis R. Rodriguez wrote:
> On Tue, Aug 09, 2016 at 01:04:00PM -0400, Mark Salter wrote:
> > 
> > On Tue, 2016-08-09 at 06:37 -0700, Guenter Roeck wrote:
> > > 
> > > On 08/09/2016 01:11 AM, Luis R. Rodriguez wrote:
> > > > 
> > > > 
> > > > Mark, Aurelien,
> > > > 
> > > > I've run into a linker (ld) issue caused by the linker table work I've
> > > > been working on [0]. I looked into this and for the life of me, I
> > > > cannot comprehend what the problem is, so was hoping you folks might
> > > > be able to chime in.
> > > > 
> > > For reference, the error is
> > > 
> > > c6x-elf-ld: drivers/built-in.o: SB-relative relocation but __c6xabi_DSBT_BASE not defined
> > > c6x-elf-ld: drivers/built-in.o: SB-relative relocation but __c6xabi_DSBT_BASE not defined
> > DSBT is a reference to the no-MMU userspace ABI used by c6x. The kernel shouldn't
> > be referencing DSBT base. The -mno-dsbt gcc flag should prevent it.
> I see -mno-dsbt on arch/c6x/Makefile already -- however at link time this is
> an issue if linker tables are used it seems. Do you have any other recommendation?
> 
> I will note that it would seem that even i386 and x86-64 compiler/binutils seem
> to have relocation issues on older compiler/binutils, for instance:

I see the problem with gcc 6 as well.

So there appears to be some toolchain issues at play here. We build the kernel with two
c6x-specific options: -mno-dsbt and -msdata=none. I already mentioned dsbt. The sdata
option may be one of:

-msdata=default
  ÂPut small global and static data in the .neardata section, which is pointed to by
  Âregister B14. Put small uninitialized global and static data in the .bss section,
  Âwhich is adjacent to the .neardata section. Put small read-only data into theÂ
  Â.rodata section. The corresponding sections used for large pieces of data are
  Â.fardata, .far and .const.

-msdata=all
  Put all data, not just small objects, into the sections reserved for small data,
  and use addressing relative to the B14 register to access them.

-msdata=none
  Make no use of the sections reserved for small data, and use absolute addresses
  to access all data. Put all initialized global and static data in the .fardata
  section, and all uninitialized data in the .far section. Put all constant data
  into the .const section.


Both small data and DSBT make use of base register + 15-bit offset to access data
and thus the SB-relative reloc in the above error message.

I think that gcc sees the .rodata section from DEFINE_LINKTABLE_RO() for builtin_fw
and thinks it needs an SB-relative reloc. When the linker sees that reloc, it thinks
it needs the dsbt base register and thus the error. Interestingly, weak data is
never put in the small data section so if gcc sees that data is weak, it doesn't
check the section name to see if it is a small data section. So SB-relative only
gets used for builtin_fw__end, but not the weak builtin_fw even though they both
are in the .rodata section.

I suspect gcc should avoid being fooled by .rodata if -msdata=none is used.
Regardless, I think this could all be avoided if the RO tables used .const
instead of .rodata for c6x.


> gcc-4.7.2
> binutils-2.22Â
> 
> Yields:
> 
> x86_64:allyesconfig || x86_64:allmodconfig
> Invalid absolute R_X86_64_64 relocation: __per_cpu_loadÂ
> 
> i386:defconfig
> Invalid absolute R_386_32 relocation: __vvar_page
> 
> This issue on x86 is not observed as so far as of gcc 5.2.1
> and binutils-2.26.1.
> 
> hpa -- if you can think of a work around for this for older compilers/linkers
> let me know... unless we are OK to increase the requirements for x86.
> 
> Â Luis