Re: [RESEND] [PATCH v2 2/4] dt-bindings: Add jdi lt070me05000 panel bindings

[Thierry Reding]

On Wed, Aug 24, 2016 at 05:34:55PM +0530, Vinay Simha wrote:
> thierry,
> 
> this is the reference pinouts of the panel
> http://www.tonylabs.com/wp-content/uploads/LT070ME05000-pinouts.jpg

I can't open that file.

> as you suggest , i will change the vcc-supply,
> 
>  - iovcc-supply: phandle of the regulator that supplies power to
>           the IOVCC voltage input (1.8 V)
> 
> will keep the other two(vddp-supply, dcdc_en-supply) remaining same.

"dcdc_en" sounds to me like it should be a GPIO rather than a regulator.

According to this datasheet:

	http://kb.52solution.com/data/uploads/2016/04/07/3172846545705cc22d050e.pdf

the input voltages are indeed VDD, VDDp and IOVCC, though with slightly
larger tolerances than the previous datasheet. VDD and VDDp can both go
from 3.0 V to 5.0 V. DCDC_EN is indeed an additional GPIO to enable the
VDDp supply.

I think you'd need something along these lines:

	- vdd-supply: LED power supply (3.0-5.0 V)
	- vddp-supply: power IC supply (3.0-5.0 V)
	- iovcc-supply: LCM power supply (1.8 V)
	- dcdc-en-gpios: power IC supply enable
	- led-en-gpios: LED backlight enable

Or perhaps your vddp-supply should be a regulator that's controlled by
the GPIO that you'd put in dcdc-en-gpios. That might work better. That
would leave only led-en-gpios as the only enable GPIOs property, so it
would be okay to keep the name "enable-gpios", I guess.

Thierry

> On Wed, Aug 24, 2016 at 5:15 PM, Thierry Reding
> <thierry.reding@xxxxxxxxx> wrote:
> > On Sun, Jul 31, 2016 at 08:45:21PM +0530, Vinay Simha BN wrote:
> >> Add documentation for lt070me05000 panel
> >>
> >> Cc: Archit Taneja <archit.taneja@xxxxxxxxx>
> >> Cc: John Stultz <john.stultz@xxxxxxxxxx>
> >> Cc: Thierry Reding <thierry.reding@xxxxxxxxx>
> >> Cc: Sumit Semwal <sumit.semwal@xxxxxxxxxx>
> >> Signed-off-by: Vinay Simha BN <simhavcs@xxxxxxxxx>
> >> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> >>
> >> ---
> >> v2:
> >>  * incorporated rob herring and thierry reviews
> >>    gpio to gpios, gpio to regulator using fixed regulators
> >>    and pwm backlight is removed, since it is controlled by
> >>    dcs commands
> >> ---
> >>  .../bindings/display/panel/jdi,lt070me05000.txt    | 57 ++++++++++++++++++++++
> >>  1 file changed, 57 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >>
> >> diff --git a/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >> new file mode 100644
> >> index 0000000..613b76f
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/display/panel/jdi,lt070me05000.txt
> >> @@ -0,0 +1,57 @@
> >> +JDI model LT070ME05000 1200x1920 7" DSI Panel
> >> +
> >> +Required properties:
> >> +- compatible: should be "jdi,lt070me05000"
> >> +- vddp-supply: phandle of the regulator that provides the supply voltage
> >> +  Power IC supply (3-5V)
> >> +- dcdc_en-supply: phandle of the regulator that provides the supply voltage
> >> +  Power IC supply enable, High active
> >> +- vcc-supply: phandle of the regulator that provides the supply voltage
> >> +  IOVCC , power supply for LCM (1.8V)
> >
> > I was just going to apply this and wanted to add some information about
> > how many lanes the panel uses, so I looked at the datasheet linked to in
> > patch 4/4:
> >
> >         http://panelone.net/en/7-0-inch/JDI_LT070ME05000_7.0_inch-datasheet
> >
> > and noticed that the power supplies in the binding here don't match the
> > ones listed in the datasheet. Granted, the datasheet is somewhat meager,
> > but it lists the following three input voltages:
> >
> >         - IOVCC at 1.8 V
> >         - VDD at 3.0 V
> >         - VDDP at 3.0 V
> >
> > This matches in part what the above binding describes, but it's not
> > quite right, so I'm wondering if the name for dcdc_en-supply came from
> > the board schematics and reflects the name of the rail on the board
> > design that provides this rather than the input voltage on the panel.
> >
> > I think we should follow the names in the panel datasheet so that people
> > can more easily reference the correct regulators when using this panel
> > on a different board. I'd suggest:
> >
> >         - iovcc-supply: phandle of the regulator that supplies power to
> >           the IOVCC voltage input (1.8 V)
> >         - vdd-supply: phandle of the regulator that supplies power to
> >           the VDD voltage input (3.0 V)
> >         - vddp-supply: phandle of the regulator that supplies power to
> >           the VDDP voltage input (3.0 V)
> >
> > Any objections?
> >
> > Thierry
> 
> 
> 
> -- 
> regards,
> vinaysimha

Attachment: signature.asc
Description: PGP signature