Re: [PATCH v2 3/3] arm: dts: thermal: add thermal/auxadc node.

[Dawei Chien]

On Tue, 2016-09-06 at 11:28 +0800, Dawei Chien wrote:
> Dear Rui,
> 
> On Tue, 2016-09-06 at 08:30 +0800, Zhang Rui wrote:
> > On ä, 2016-09-06 at 08:24 +0800, Zhang Rui wrote:
> > > On å, 2016-08-18 at 11:50 +0800, Dawei Chien wrote:
> > > > 
> > > > This adds the thermal controller and auxadc nodes
> > > > to the Mediatek MT2701 dtsi file.
> > > > 
> > > > Signed-off-by: Dawei Chien <dawei.chien@xxxxxxxxxxxx>
> > > > ---
> > > > This patch depned on:
> > > > https://patchwork.kernel.org/patch/9249589/
> > > > https://patchwork.kernel.org/patch/9249589/
> > > Hmm, does this mean that I should take all these three patches and
> > > hold
> > > the patches in next merge window until the above patch has been
> > > merged?
> > > 
> Yes, this patch is base on auxadc patchset.
> 
> > Patch 3/3 can not be applied on top of upstream kernel, so I guess it
> > still has some other dependencies.
> > I think I can apply patch 1, 2 first. And patch 3/3 should be handled
> > in the dt tree.
> 
> Sorry, this patch is also need Mediatek's clock patchset what I miss to
> add in dependency list, I would resend this dt tree once clock patch
> merge, or resend this for right dependency on next version, thank you.

Actually, since patch1/patch2 would be OK so far, I would just only
resend patch3 after MTK clock pathcset ready, I prefer to merge
patch1/patch2 if possible, thank you.


> > thanks,
> > rui
> > > thanks,
> > > rui 
> > > > 
> > > > ---
> > > >  arch/arm/boot/dts/mt2701.dtsi |   44
> > > > +++++++++++++++++++++++++++++++++++++++++
> > > >  1 file changed, 44 insertions(+)
> > > > 
> > > > diff --git a/arch/arm/boot/dts/mt2701.dtsi
> > > > b/arch/arm/boot/dts/mt2701.dtsi
> > > > index e9150a4..cee4724 100644
> > > > --- a/arch/arm/boot/dts/mt2701.dtsi
> > > > +++ b/arch/arm/boot/dts/mt2701.dtsi
> > > > @@ -87,6 +87,36 @@
> > > >  		clock-output-names = "rtc32k";
> > > >  	};
> > > >  
> > > > +	thermal-zones {
> > > > +		cpu_thermal: cpu_thermal {
> > > > +			polling-delay-passive = <1000>; /*
> > > > milliseconds */
> > > > +			polling-delay = <1000>; /* milliseconds */
> > > > +
> > > > +			thermal-sensors = <&thermal 0>;
> > > > +			sustainable-power = <1000>;
> > > > +
> > > > +			trips {
> > > > +				threshold: trip-point@0 {
> > > > +					temperature = <68000>;
> > > > +					hysteresis = <2000>;
> > > > +					type = "passive";
> > > > +				};
> > > > +
> > > > +				target: trip-point@1 {
> > > > +					temperature = <85000>;
> > > > +					hysteresis = <2000>;
> > > > +					type = "passive";
> > > > +				};
> > > > +
> > > > +				cpu_crit: cpu_crit@0 {
> > > > +					temperature = <115000>;
> > > > +					hysteresis = <2000>;
> > > > +					type = "critical";
> > > > +				};
> > > > +			};
> > > > +		};
> > > > +	};
> > > > +
> > > >  	timer {
> > > >  		compatible = "arm,armv7-timer";
> > > >  		interrupt-parent = <&gic>;
> > > > @@ -222,4 +252,18 @@
> > > >  		clock-names = "baud", "bus";
> > > >  		status = "disabled";
> > > >  	};
> > > > +
> > > > +	thermal: thermal@1100b000 {
> > > > +		#thermal-sensor-cells = <0>;
> > > > +		compatible = "mediatek,mt2701-thermal";
> > > > +		reg = <0 0x1100b000 0 0x1000>;
> > > > +		interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_LOW>;
> > > > +		clocks = <&pericfg CLK_PERI_THERM>, <&pericfg
> > > > CLK_PERI_AUXADC>;
> > > > +		clock-names = "therm", "auxadc";
> > > > +		resets = <&pericfg 0x10>;
> > > > +		reset-names = "therm";
> > > > +		mediatek,auxadc = <&auxadc>;
> > > > +		mediatek,apmixedsys = <&apmixedsys>;
> > > > +	};
> > > > +
> > > >  };
> > > --
> > > To unsubscribe from this list: send the line "unsubscribe linux-pm"
> > > in
> > > the body of a message to majordomo@xxxxxxxxxxxxxxx
> > > More majordomo info at  http://vger.kernel.org/majordomo-info.html
>