Re: [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware

[Chanwoo Choi]

Hi Stephen,

Looks good to me.
But, there are something that need to be modified.
- add the author information
- add the description of driver
- use the extcon_set_state() instead of extcon_set_cable_state_()

I modified this patch and applied it because I should send
the pull request within this week after releasing the rc6.

I added the comment about the modification.

On 2016ë 09ì 10ì 06:48, Stephen Boyd wrote:
> Some Qualcomm PMICs have a misc device that performs USB id pin
> detection via an interrupt. When the interrupt triggers, we
> should read the interrupt line to see if it has gone high or low.
> If the interrupt is low then the ID pin is grounded, and if the
> interrupt is high then the ID pin is being held high.
> 
> Cc: Roger Quadros <rogerq@xxxxxx>
> Cc: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
> Signed-off-by: Stephen Boyd <stephen.boyd@xxxxxxxxxx>
> ---
> 
> Changes from v1:
>  * Fixed Makefile ordering
>  * Fixed up copyright markings
> 
>  .../bindings/extcon/qcom,pm8941-misc.txt           |  41 +++++
>  drivers/extcon/Kconfig                             |   6 +
>  drivers/extcon/Makefile                            |   1 +
>  drivers/extcon/extcon-qcom-spmi-misc.c             | 167 +++++++++++++++++++++
>  4 files changed, 215 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
>  create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c
> 
> diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
> new file mode 100644
> index 000000000000..35383adb10f1
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt
> @@ -0,0 +1,41 @@
> +Qualcomm's PM8941 USB ID Extcon device
> +
> +Some Qualcomm PMICs have a "misc" module that can be used to detect when
> +the USB ID pin has been pulled low or high.
> +
> +PROPERTIES
> +
> +- compatible:
> +    Usage: required
> +    Value type: <string>
> +    Definition: Should contain "qcom,pm8941-misc";
> +
> +- reg:
> +    Usage: required
> +    Value type: <u32>
> +    Definition: Should contain the offset to the misc address space
> +
> +- interrupts:
> +    Usage: required
> +    Value type: <prop-encoded-array>
> +    Definition: Should contain the usb id interrupt
> +
> +- interrupt-names:
> +    Usage: required
> +    Value type: <stringlist>
> +    Definition: Should contain the string "usb_id" for the usb id interrupt
> +
> +Example:
> +
> +	pmic {
> +		usb_id: misc@900 {
> +			compatible = "qcom,pm8941-misc";
> +			reg = <0x900>;
> +			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
> +			interrupt-names = "usb_id";
> +		};
> +	}
> +
> +	usb-controller {
> +		extcon = <&usb_id>;
> +	};
> diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig
> index 3d89e60a3e71..04788d92ea52 100644
> --- a/drivers/extcon/Kconfig
> +++ b/drivers/extcon/Kconfig
> @@ -96,6 +96,12 @@ config EXTCON_PALMAS
>  	  Say Y here to enable support for USB peripheral and USB host
>  	  detection by palmas usb.
>  
> +config EXTCON_QCOM_SPMI_MISC
> +	tristate "Qualcomm USB extcon support"
> +	help
> +	  Say Y here to enable SPMI PMIC based USB cable detection
> +	  support on Qualcomm PMICs such as PM8941.
> +
>  config EXTCON_RT8973A
>  	tristate "Richtek RT8973A EXTCON support"
>  	depends on I2C
> diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile
> index 972c813c375b..31a0a999c4fb 100644
> --- a/drivers/extcon/Makefile
> +++ b/drivers/extcon/Makefile
> @@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693)	+= extcon-max77693.o
>  obj-$(CONFIG_EXTCON_MAX77843)	+= extcon-max77843.o
>  obj-$(CONFIG_EXTCON_MAX8997)	+= extcon-max8997.o
>  obj-$(CONFIG_EXTCON_PALMAS)	+= extcon-palmas.o
> +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o
>  obj-$(CONFIG_EXTCON_RT8973A)	+= extcon-rt8973a.o
>  obj-$(CONFIG_EXTCON_SM5502)	+= extcon-sm5502.o
>  obj-$(CONFIG_EXTCON_USB_GPIO)	+= extcon-usb-gpio.o
> diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c
> new file mode 100644
> index 000000000000..1b8e24494c60
> --- /dev/null
> +++ b/drivers/extcon/extcon-qcom-spmi-misc.c
> @@ -0,0 +1,167 @@
> +/**
> + * Based on extcon-usb-gpio.c

I think that following description is better than before.
I'll modify it.

  * extcon-qcom-spmi-misc.c - Qualcomm USB extcon driver to support USB ID
  *                             detection based on extcon-usb-gpio.c.

> + *
> + * Copyright (C) 2016 Linaro Ltd

s/Ltd/Ltd.

You are missing the author information. I'll add following information:
    * Stephen Boyd <stephen.boyd@xxxxxxxxxx>

> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/extcon.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/workqueue.h>
> +
> +#define USB_ID_DEBOUNCE_MS	5	/* ms */
> +
> +struct qcom_usb_extcon_info {
> +	struct extcon_dev *edev;
> +	int irq;
> +	struct delayed_work wq_detcable;
> +	unsigned long debounce_jiffies;
> +};
> +
> +static const unsigned int qcom_usb_extcon_cable[] = {
> +	EXTCON_USB_HOST,
> +	EXTCON_NONE,
> +};
> +
> +static void qcom_usb_extcon_detect_cable(struct work_struct *work)
> +{
> +	bool id;
> +	int ret;
> +	struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work),
> +						    struct qcom_usb_extcon_info,
> +						    wq_detcable);
> +
> +	/* check ID and update cable state */
> +	ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id);
> +	if (ret)
> +		return;
> +
> +	extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id);

The extcon_set_cable_state_() is deprecated.
Instead, I'll modify it using extcon_set_state() as following:

	extcon_set_state(info->edev, EXTCON_USB_HOST, !id);

> +}
> +
> +static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id)
> +{
> +	struct qcom_usb_extcon_info *info = dev_id;
> +
> +	queue_delayed_work(system_power_efficient_wq, &info->wq_detcable,
> +			   info->debounce_jiffies);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static int qcom_usb_extcon_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct qcom_usb_extcon_info *info;
> +	int ret;
> +
> +	info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL);
> +	if (!info)
> +		return -ENOMEM;
> +
> +	info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable);
> +	if (IS_ERR(info->edev)) {
> +		dev_err(dev, "failed to allocate extcon device\n");
> +		return -ENOMEM;
> +	}
> +
> +	ret = devm_extcon_dev_register(dev, info->edev);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to register extcon device\n");
> +		return ret;
> +	}
> +
> +	info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS);
> +	INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable);
> +
> +	info->irq = platform_get_irq_byname(pdev, "usb_id");
> +	if (info->irq < 0)
> +		return info->irq;
> +
> +	ret = devm_request_threaded_irq(dev, info->irq, NULL,
> +					qcom_usb_irq_handler,
> +					IRQF_TRIGGER_RISING |
> +					IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
> +					pdev->name, info);
> +	if (ret < 0) {
> +		dev_err(dev, "failed to request handler for ID IRQ\n");
> +		return ret;
> +	}
> +
> +	platform_set_drvdata(pdev, info);
> +	device_init_wakeup(dev, 1);
> +
> +	/* Perform initial detection */
> +	qcom_usb_extcon_detect_cable(&info->wq_detcable.work);
> +
> +	return 0;
> +}
> +
> +static int qcom_usb_extcon_remove(struct platform_device *pdev)
> +{
> +	struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev);
> +
> +	cancel_delayed_work_sync(&info->wq_detcable);
> +
> +	return 0;
> +}
> +
> +#ifdef CONFIG_PM_SLEEP
> +static int qcom_usb_extcon_suspend(struct device *dev)
> +{
> +	struct qcom_usb_extcon_info *info = dev_get_drvdata(dev);
> +	int ret = 0;
> +
> +	if (device_may_wakeup(dev))
> +		ret = enable_irq_wake(info->irq);
> +
> +	return ret;
> +}
> +
> +static int qcom_usb_extcon_resume(struct device *dev)
> +{
> +	struct qcom_usb_extcon_info *info = dev_get_drvdata(dev);
> +	int ret = 0;
> +
> +	if (device_may_wakeup(dev))
> +		ret = disable_irq_wake(info->irq);
> +
> +	return ret;
> +}
> +#endif
> +
> +static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops,
> +			 qcom_usb_extcon_suspend, qcom_usb_extcon_resume);
> +
> +static const struct of_device_id qcom_usb_extcon_dt_match[] = {
> +	{ .compatible = "qcom,pm8941-misc", },
> +	{ }
> +};
> +MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match);
> +
> +static struct platform_driver qcom_usb_extcon_driver = {
> +	.probe		= qcom_usb_extcon_probe,
> +	.remove		= qcom_usb_extcon_remove,
> +	.driver		= {
> +		.name	= "extcon-pm8941-misc",
> +		.pm	= &qcom_usb_extcon_pm_ops,
> +		.of_match_table = qcom_usb_extcon_dt_match,
> +	},
> +};
> +module_platform_driver(qcom_usb_extcon_driver);
> +
> +MODULE_DESCRIPTION("QCOM USB ID extcon driver");

You are missing the author information. I'll add it as following:

	MODULE_AUTHOR("Stephen Boyd <stephen.boyd@xxxxxxxxxx>");

> +MODULE_LICENSE("GPL v2");
> 

-- 
Best Regards,
Chanwoo Choi