Re: [PATCH] BUG: atmel_serial: Interrupts not disabled on close

From: Nicolas Ferre
Date: Mon Sep 12 2016 - 11:23:10 EST


Le 12/09/2016 à 15:34, Richard Genoud a écrit :
> Since commit 18dfef9c7f87 ("serial: atmel: convert to irq handling
> provided mctrl-gpio"), interrupts from GPIOs are not disabled any more
> when the serial port is closed, leading to an oops when the one of the
> input pin is toggled (CTS/DSR/DCD/RNG).
>
> This is only the case if those pins are used as GPIOs, i.e. declared
> like that:
> usart1: serial@f8020000 {
> /* CTS and DTS will be handled by GPIO */
> status = "okay";
> rts-gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
> cts-gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
> dtr-gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
> dsr-gpios = <&pioC 31 GPIO_ACTIVE_LOW>;
> rng-gpios = <&pioB 12 GPIO_ACTIVE_LOW>;
> dcd-gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
> };
>
> That's because modem interrupts used to be freed in atmel_shutdown().
> After commit 18dfef9c7f87 ("serial: atmel: convert to irq handling
> provided mctrl-gpio"), this code was just removed.
> Calling atmel_disable_ms() disables the interrupts and everything works
> fine again.
>
> Tested on at91sam9g35-cm
>
> (This patch doesn't apply on -stable kernels, fixes for 4.4 and 4.7 will
> be sent after this one is applied.)
>
> Signed-off-by: Richard Genoud <richard.genoud@xxxxxxxxx>
> Fixes: 18dfef9c7f87 ("serial: atmel: convert to irq handling provided mctrl-gpio")

I thinks it's a bit late for "4.8-fixes".

Greg, tell me if you want that I add the Cc: stable tag to this patch
(as advised by Uwe) and re-send?

Acked-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>

Thanks Richard!

Best regards,

> ---
> drivers/tty/serial/atmel_serial.c | 5 +++--
> 1 file changed, 3 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 2eaa18ddef61..8bbde52db376 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -1929,6 +1929,9 @@ static void atmel_shutdown(struct uart_port *port)
> {
> struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>
> + /* Disable modem control lines interrupts */
> + atmel_disable_ms(port);
> +
> /* Disable interrupts at device level */
> atmel_uart_writel(port, ATMEL_US_IDR, -1);
>
> @@ -1979,8 +1982,6 @@ static void atmel_shutdown(struct uart_port *port)
> */
> free_irq(port->irq, port);
>
> - atmel_port->ms_irq_enabled = false;
> -
> atmel_flush_buffer(port);
> }
>
>


--
Nicolas Ferre