Re: [RFC PATCH v2 1/2] ARM: dts: samsung: add rga-lvds panel in itop elite

[Krzysztof Kozlowski]

On Sun, Sep 18, 2016 at 10:27:38PM +0800, Randy Li wrote:
> It is actually a lvds panel connected through a rga-lvds bridge.
> The touchscreen is communicated with i2c bus but the driver is not
> support now.
> 
> Signed-off-by: Randy Li <ayaka@xxxxxxxxxxx>

Subject: ARM: dts: exynos

> ---
>  arch/arm/boot/dts/exynos4412-itop-elite.dts | 54 +++++++++++++++++++++++++++--
>  1 file changed, 52 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
> index b08705e..9ef0505 100644
> --- a/arch/arm/boot/dts/exynos4412-itop-elite.dts
> +++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
> @@ -138,6 +138,36 @@
>  		assigned-clocks = <&clock CLK_MOUT_CAM0>;
>  		assigned-clock-parents = <&clock CLK_XUSBXTI>;
>  	};
> +
> +	vcc_sys_lcd: sys-lcd {

No underscores, use hyphens.

> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc_5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;

Isn't this one of S5M8767 PMIC regulators? If so, then it should be
defined there... On the other hand, the PMIC supports GPIO enable
control only for buck9...

> +	};
> +
> +	panel: panel@0 {
> +		compatible = "chunghwa,claa070wp03xg";
> +
> +		power-supply = <&vcc_sys_lcd>;
> +		enable-gpios = <&gpl0 2 GPIO_ACTIVE_HIGH>;
> +		backlight = <&bl>;
> +
> +		port {
> +			lcd_ep: endpoint {

lcd-ep

> +				remote-endpoint = <&rga_lvds>;
> +			};
> +		};
> +	};
> +
> +	bl: backlight {
> +		compatible = "pwm-backlight";
> +		pwms = <&pwm 1 5000000 PWM_POLARITY_INVERTED>;
> +		brightness-levels = <0 5 12 16 32 64 128 255>;
> +		default-brightness-level = <5>;
> +		power-supply = <&vcc_sys_lcd>;
> +	};
>  };
>  
>  &adc {
> @@ -215,9 +245,9 @@
>  
>  &pwm {
>  	status = "okay";
> -	pinctrl-0 = <&pwm0_out>;
> +	pinctrl-0 = <&pwm0_out &pwm1_out>;
>  	pinctrl-names = "default";
> -	samsung,pwm-outputs = <0>;
> +	samsung,pwm-outputs = <0>, <1>;
>  };
>  
>  &sdhci_2 {
> @@ -238,3 +268,23 @@
>  &serial_2 {
>  	status = "okay";
>  };
> +
> +&i2c_3 {
> +	status = "okay";
> +};
> +
> +&fimd {

Please put these nodes in alphabetical order. I asked about it for
initial DTS and it applies still.

> +	pinctrl-0 = <&lcd_clk &lcd_data24>;
> +	pinctrl-names = "default";
> +	status = "okay";
> +	ports {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		port@3 {
> +			reg = <3>;
> +			rga_lvds: endpoint {

rga-lvds

Best regards,
Krzysztof

> +				remote-endpoint = <&lcd_ep>;
> +			};
> +		};
> +	};
> +};
> -- 
> 2.7.4
>