[PATCH v1] ARM: at91/dt: add dts file for sama5d36ek CMP board

[Wenyou Yang]

The difference between sama5d36ek_cmp.dts and sama5d36ek.dts
is listed as below.
 1. The USB host nodes are removed, that is, the USB host is disabled.
 2. The gpio_keys node is added to wake up from the sleep.
 3. The sama5d3xdm.dtsi isn't included, because the pins for LCD are
    conflicted with one for gpio_keys.

As said in errata, "When the USB host ports are used in high speed
mode (EHCI), it is not possible to suspend the ports if no device is
attached on each port. This leads to increased power consumption even
if the system is in a low power mode." That is why the the USB host
isn't enabled.

Signed-off-by: Wenyou Yang <wenyou.yang@xxxxxxxxx>
---

 arch/arm/boot/dts/sama5d36ek_cmp.dts  |  51 ++++++++
 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 ++++++++++++++++++++++++
 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 230 ++++++++++++++++++++++++++++++++++
 3 files changed, 447 insertions(+)
 create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
 create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
 create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi

diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
new file mode 100644
index 0000000..fd6bcd6
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
@@ -0,0 +1,51 @@
+/*
+ * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+#include "sama5d3xmb_cmp.dtsi"
+
+/ {
+	model = "Atmel SAMA5D36-EK";
+	compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";
+
+	ahb {
+		apb {
+			spi0: spi@f0004000 {
+				status = "okay";
+			};
+
+			ssc0: ssc@f0008000 {
+				status = "okay";
+			};
+
+			can0: can@f000c000 {
+				status = "okay";
+			};
+
+			i2c0: i2c@f0014000 {
+				status = "okay";
+			};
+
+			i2c1: i2c@f0018000 {
+				status = "okay";
+			};
+
+			macb0: ethernet@f0028000 {
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				status = "okay";
+			};
+		};
+	};
+
+	sound {
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
new file mode 100644
index 0000000..77638c3
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
@@ -0,0 +1,166 @@
+/*
+ * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+/ {
+	compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		reg = <0x20000000 0x20000000>;
+	};
+
+	clocks {
+		slow_xtal {
+			clock-frequency = <32768>;
+		};
+
+		main_xtal {
+			clock-frequency = <12000000>;
+		};
+	};
+
+	ahb {
+		apb {
+			spi0: spi@f0004000 {
+				cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
+			};
+
+			macb0: ethernet@f0028000 {
+				phy-mode = "rgmii";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ethernet-phy@1 {
+					reg = <0x1>;
+					interrupt-parent = <&pioB>;
+					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+					txen-skew-ps = <800>;
+					txc-skew-ps = <3000>;
+					rxdv-skew-ps = <400>;
+					rxc-skew-ps = <3000>;
+					rxd0-skew-ps = <400>;
+					rxd1-skew-ps = <400>;
+					rxd2-skew-ps = <400>;
+					rxd3-skew-ps = <400>;
+				};
+
+				ethernet-phy@7 {
+					reg = <0x7>;
+					interrupt-parent = <&pioB>;
+					interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+					txen-skew-ps = <800>;
+					txc-skew-ps = <3000>;
+					rxdv-skew-ps = <400>;
+					rxc-skew-ps = <3000>;
+					rxd0-skew-ps = <400>;
+					rxd1-skew-ps = <400>;
+					rxd2-skew-ps = <400>;
+					rxd3-skew-ps = <400>;
+				};
+			};
+
+			i2c1: i2c@f0018000 {
+				pmic: act8865@5b {
+					compatible = "active-semi,act8865";
+					reg = <0x5b>;
+					status = "disabled";
+
+					regulators {
+						vcc_1v8_reg: DCDC_REG1 {
+							regulator-name = "VCC_1V8";
+							regulator-min-microvolt = <1800000>;
+							regulator-max-microvolt = <1800000>;
+							regulator-always-on;
+						};
+
+						vcc_1v2_reg: DCDC_REG2 {
+							regulator-name = "VCC_1V2";
+							regulator-min-microvolt = <1100000>;
+							regulator-max-microvolt = <1300000>;
+							regulator-always-on;
+						};
+
+						vcc_3v3_reg: DCDC_REG3 {
+							regulator-name = "VCC_3V3";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vddana_reg: LDO_REG1 {
+							regulator-name = "VDDANA";
+							regulator-min-microvolt = <3300000>;
+							regulator-max-microvolt = <3300000>;
+							regulator-always-on;
+						};
+
+						vddfuse_reg: LDO_REG2 {
+							regulator-name = "FUSE_2V5";
+							regulator-min-microvolt = <2500000>;
+							regulator-max-microvolt = <2500000>;
+						};
+					};
+				};
+			};
+		};
+
+		nand0: nand@60000000 {
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			atmel,has-pmecc;
+			atmel,pmecc-cap = <4>;
+			atmel,pmecc-sector-size = <512>;
+			nand-on-flash-bbt;
+			status = "okay";
+
+			at91bootstrap@0 {
+				label = "at91bootstrap";
+				reg = <0x0 0x40000>;
+			};
+
+			bootloader@40000 {
+				label = "bootloader";
+				reg = <0x40000 0x80000>;
+			};
+
+			bootloaderenv@c0000 {
+				label = "bootloader env";
+				reg = <0xc0000 0xc0000>;
+			};
+
+			dtb@180000 {
+				label = "device tree";
+				reg = <0x180000 0x80000>;
+			};
+
+			kernel@200000 {
+				label = "kernel";
+				reg = <0x200000 0x600000>;
+			};
+
+			rootfs@800000 {
+				label = "rootfs";
+				reg = <0x800000 0x0f800000>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		d2 {
+			label = "d2";
+			gpios = <&pioE 25 GPIO_ACTIVE_LOW>;	/* PE25, conflicts with A25, RXD2 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
new file mode 100644
index 0000000..3ec78867
--- /dev/null
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -0,0 +1,230 @@
+/*
+ * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
+ *
+ *  Copyright (C) 2016 Atmel,
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "sama5d3xcm_cmp.dtsi"
+
+/ {
+	compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";
+
+	ahb {
+		apb {
+			mmc0: mmc@f0000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			spi0: spi@f0004000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
+
+				m25p80@0 {
+					compatible = "atmel,at25df321a";
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+				};
+			};
+
+			ssc0: ssc@f0008000 {
+				atmel,clk-from-rk-pin;
+			};
+
+			/*
+			 * i2c0 conflicts with ISI:
+			 * disable it to allow the use of ISI
+			 * can not enable audio when i2c0 disabled
+			 */
+			i2c0: i2c@f0014000 {
+				wm8904: wm8904@1a {
+					compatible = "wlf,wm8904";
+					reg = <0x1a>;
+					clocks = <&pck0>;
+					clock-names = "mclk";
+				};
+			};
+
+			i2c1: i2c@f0018000 {
+				ov2640: camera@0x30 {
+					compatible = "ovti,ov2640";
+					reg = <0x30>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+					resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
+					pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
+					/* use pck1 for the master clock of ov2640 */
+					clocks = <&pck1>;
+					clock-names = "xvclk";
+					assigned-clocks = <&pck1>;
+					assigned-clock-rates = <25000000>;
+
+					port {
+						ov2640_0: endpoint {
+							remote-endpoint = <&isi_0>;
+							bus-width = <8>;
+						};
+					};
+				};
+			};
+
+			usart1: serial@f0020000 {
+				dmas = <0>, <0>;	/*  Do not use DMA for usart1 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
+				status = "okay";
+			};
+
+			isi: isi@f0034000 {
+				port {
+					isi_0: endpoint {
+						remote-endpoint = <&ov2640_0>;
+						bus-width = <8>;
+						vsync-active = <1>;
+						hsync-active = <1>;
+					};
+				};
+			};
+
+			mmc1: mmc@f8000000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
+				status = "okay";
+				slot@0 {
+					reg = <0>;
+					bus-width = <4>;
+					cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
+				};
+			};
+
+			adc0: adc@f8018000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <
+					&pinctrl_adc0_adtrg
+					&pinctrl_adc0_ad0
+					&pinctrl_adc0_ad1
+					&pinctrl_adc0_ad2
+					&pinctrl_adc0_ad3
+					&pinctrl_adc0_ad4
+					>;
+				status = "okay";
+			};
+
+			macb1: ethernet@f802c000 {
+				phy-mode = "rmii";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+				phy0: ethernet-phy@1 {
+					/*interrupt-parent = <&pioE>;*/
+					/*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
+					reg = <1>;
+				};
+			};
+
+			pinctrl@fffff200 {
+				board {
+					pinctrl_gpio_keys: gpio_keys {
+						atmel,pins =
+							<AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+					};
+
+					pinctrl_mmc0_cd: mmc0_cd {
+						atmel,pins =
+							<AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
+					};
+
+					pinctrl_mmc1_cd: mmc1_cd {
+						atmel,pins =
+							<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
+					};
+
+					pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
+						atmel,pins =
+							<AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PD30 periph B */
+					};
+
+					pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+						atmel,pins =
+							<AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;	/* PD31 periph B ISI_MCK */
+					};
+
+					pinctrl_sensor_reset: sensor_reset-0 {
+						atmel,pins =
+							<AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;   /* PE24 gpio */
+					};
+
+					pinctrl_sensor_power: sensor_power-0 {
+						atmel,pins =
+							<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
+					};
+
+					pinctrl_usba_vbus: usba_vbus {
+						atmel,pins =
+							<AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */
+					};
+				};
+			};
+
+			dbgu: serial@ffffee00 {
+				dmas = <0>, <0>;	/*  Do not use DMA for dbgu */
+				status = "okay";
+			};
+
+			watchdog@fffffe40 {
+				status = "okay";
+			};
+		};
+
+		usb0: gadget@00500000 {
+			atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usba_vbus>;
+			status = "okay";
+		};
+	};
+
+	sound {
+		compatible = "atmel,asoc-wm8904";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
+
+		atmel,model = "wm8904 @ SAMA5D3EK";
+		atmel,audio-routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Mic", "MICBIAS",
+			"IN1L", "Mic";
+
+		atmel,ssc-controller = <&ssc0>;
+		atmel,audio-codec = <&wm8904>;
+
+		status = "disabled";
+	};
+
+	/* Conflict with LCD pins */
+	gpio_keys {
+		compatible = "gpio-keys";
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		pb_user1 {
+			label = "pb_user1";
+			gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
+			linux,code = <0x100>;
+			gpio-key,wakeup;
+		};
+	};
+};
-- 
2.7.4