[PATCH 1/3] Documentation: dt: reset: Add TI SCI reset binding

[Andrew F. Davis]

Add TI SCI reset controller binding. This describes the DT binding
details for a reset controller node providing reset management services
to hardware blocks (reset consumers) using the Texas Instrument's System
Control Interface (TI SCI) protocol to communicate to a system controller
block present on the SoC.

Signed-off-by: Andrew F. Davis <afd@xxxxxx>
[s-anna@xxxxxx: revise the binding format]
Signed-off-by: Suman Anna <s-anna@xxxxxx>
Signed-off-by: Nishanth Menon <nm@xxxxxx>
---
 .../devicetree/bindings/reset/ti,sci-reset.txt     | 68 ++++++++++++++++++++++
 MAINTAINERS                                        |  1 +
 2 files changed, 69 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/reset/ti,sci-reset.txt

diff --git a/Documentation/devicetree/bindings/reset/ti,sci-reset.txt b/Documentation/devicetree/bindings/reset/ti,sci-reset.txt
new file mode 100644
index 0000000..189e284
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/ti,sci-reset.txt
@@ -0,0 +1,68 @@
+Texas Instruments System Control Interface (TI-SCI) Reset Controller
+=====================================================================
+
+Some TI SoCs contain a system controller (like the Power Management Micro
+Controller (PMMC) on Keystone K2G SoC) that are responsible for controlling
+the state of the various hardware modules present on the SoC. Communication
+between the host processor running an OS and the system controller happens
+through a protocol called TI System Control Interface (TI-SCI protocol).
+For TI SCI details, please refer to the document,
+Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
+
+TI-SCI Reset Controller Node
+============================
+This reset controller node uses the TI SCI protocol to perform the reset
+management of various hardware modules present on the SoC.
+
+Required properties:
+--------------------
+ - compatible	: Should be "ti,sci-reset"
+ - ti,sci	: phandle to the TI SCI device to use for managing resets
+ - #reset-cells	: Should be 2. Please see the reset consumer node below for
+		  usage details.
+
+TI-SCI Reset Consumer Nodes
+===========================
+Each of the reset consumer nodes should have the following properties,
+in addition to their own properties.
+
+Required properties:
+--------------------
+ - resets	: A phandle and reset specifier pair, one pair for each reset
+		  signal that affects the device, or that the device manages.
+		  The phandle should point to the TI-SCI reset controller node,
+		  and the reset specifier should have 2 cell-values. The first
+		  cell should contain the device ID, the values of which are
+		  specified in the <dt-bindings/genpd/<soc>.h> include file.
+		  The second cell should contain the reset mask value used by
+		  system controller, the values of which are specified in the
+		  include file <dt-bindings/reset/<soc>.h>, where <soc> is the
+		  name of the SoC involved, for example 'k2g'.
+
+Please also refer to Documentation/devicetree/bindings/reset/reset.txt for
+common reset controller usage by consumers.
+
+
+Example:
+--------
+The following example demonstrates both a TI-SCI reset controller node and a
+consumer (a DSP device) on the K2G SoC.
+
+#include <dt-bindings/genpd/k2g.h>
+#include <dt-bindings/reset/k2g.h>
+
+/ {
+	soc {
+		k2g_reset: k2g_reset {
+			compatible = "ti,sci-reset";
+			ti,sci = <&pmmc>;
+			#reset-cells = <2>;
+		};
+
+		dsp0: dsp0 {
+			...
+			resets = <&k2g_reset K2G_DEV_CGEM0 K2G_DEV_CGEM0_DSP0_RESET>;
+			...
+		};
+	};
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index 6e93976..d8068df 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -11899,6 +11899,7 @@ F:	drivers/soc/ti/ti_sci_pm_domains.c
 F:	Documentation/devicetree/bindings/clock/ti,sci-clk.txt
 F:	include/dt-bindings/clock/k2g.h
 F:	drivers/clk/keystone/sci-clk.c
+F:	Documentation/devicetree/bindings/reset/ti,sci-reset.txt
 
 THANKO'S RAREMONO AM/FM/SW RADIO RECEIVER USB DRIVER
 M:	Hans Verkuil <hverkuil@xxxxxxxxx>
-- 
2.10.1