[PATCH v3 3/5] arm64: dts: exynos: Add dts files for Samsung Exynos5433 64bit SoC

From: Chanwoo Choi
Date: Thu Nov 03 2016 - 02:40:24 EST

Next message: Chanwoo Choi: "[PATCH v3 2/5] pinctrl: samsung: Add GPF support for Exynos5433"
Previous message: Chanwoo Choi: "[PATCH v3 1/5] pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank"
In reply to: Krzysztof Kozlowski: "Re: [PATCH v3 1/5] pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank"
Next in thread: Andi Shyti: "Re: [PATCH v3 3/5] arm64: dts: exynos: Add dts files for Samsung Exynos5433 64bit SoC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

This patch adds new Exynos5433 dtsi to support 64-bit Exynos5433 SoC based on
Octa-core CPUs (quad Cortex-A57 and quad Cortex-A53). And Exynos5433 supports
PSCI (Power State Coordination Interface) v0.1.

This patch includes following Device Tree node to support Exynos5433 SoC:
1. Octa cores for big.LITTLE architecture
- Cortex-A53 LITTLE Quad-core
- Cortex-A57 big Quad-core
- Support PSCI v0.1

2. Clock controller node
- CMU_TOP : clocks for IMEM/FSYS/G3D/GSCL/HEVC/MSCL/G2D/MFC/PERIC/PERIS
- CMU_CPIF : clocks for LLI (Low Latency Interface)
- CMU_MIF : clocks for DRAM Memory Controller
- CMU_PERIC : clocks for UART/I2C/SPI/I2S/PCM/SPDIF/PWM/SLIMBUS
- CMU_PERIS : clocks for PMU/TMU/MCT/WDT/RTC/SECKEY/TZPC
- CMU_FSYS : clocks for USB/UFS/SDMMC/TSI/PDMA
- CMU_G2D : clocks for G2D/MDMA
- CMU_DISP : clocks for DECON/HDMI/DSIM/MIXER
- CMU_AUD : clocks for Cortex-A5/BUS/AUDIO
- CMU_BUS{0|1|2} : clocks for global data buses and global peripheral buses
- CMU_G3D : clocks for 3D Graphics Engine
- CMU_GSCL : clocks for GSCALER
- CMU_APOLLO: clocks for Cortex-A53 Quad-core processor.
- CMU_ATLAS : clocks for Cortex-A57 Quad-core processor,
CoreSight and L2 cache controller.
- CMU_MSCL : clocks for M2M (Memory to Memory) scaler and JPEG IPs.
- CMU_MFC : clocks for MFC (Multi-Format Codec) IP.
- CMU_HEVC : clocks for HEVC(High Efficiency Video Codec) decoder IP.
- CMU_ISP : clocks for FIMC-ISP/DRC/SCLC/DIS/3DNR IPs.
- CMU_CAM0 : clocks for MIPI_CSIS{0|1}/FIMC_LITE_{A|B|D}/FIMC_3AA{0|1} IPs.
- CMU_CAM1 : clocks for COrtex-A5/MIPI_CSIS2/FIMC_LITE_C/FIMC-FD IPs.

3. pinctrl node for GPIO
- alive/aud/cpif/ese/finger/fsys/imem/nfc/peric/touch pad

4. Timer
- ARM architecture timer (armv8-timer)
- MCT (Multi Core Timer) timer

5. Interrupt controller (GIC-400)

6. BUS devices
- HS-I2C (High-Speed I2C) device
- SPI (Serial Peripheral Interface) device

7. Sound devices
- I2S bus
- LPASS (Low Power Audio Subsystem)

8. Power management devices
- CPUFREQ for for Cortex-A53/A57
- TMU (Thermal Management Unit) for Cortex-A53/A57, G3D, ISP

9. Display controller devices
- DECON (Display and enhancement controller) for panel output
- DSI (Display Serial Interface)
- MIC (Mobile Image Compressor)

10. USB
- USB 3.0 DRD (Dual Role Device) controller
- USB 3.0 Host controller

11. Storage devices
- MSHC (Mobile Storage Host Controller)

12. Misc devices
- UART device
- ADC (Analog Digital Converter)
- PWM (Pulse Width Modulation)
- ADMA (Advanced DMA) and PDMA (Peripheral DMA)

Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
Signed-off-by: Jaehoon Chung <jh80.chung@xxxxxxxxxxx>
Signed-off-by: Seung-Woo Kim <sw0312.kim@xxxxxxxxxxx>
Signed-off-by: Joonyoung Shim <jy0922.shim@xxxxxxxxxxx>
Signed-off-by: Inki Dae <inki.dae@xxxxxxxxxxx>
Signed-off-by: Jonghwa Lee <jonghwa3.lee@xxxxxxxxxxx>
Signed-off-by: Beomho Seo <beomho.seo@xxxxxxxxxxx>
Signed-off-by: Jaewon Kim <jaewon02.kim@xxxxxxxxxxx>
Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx>
Signed-off-by: Inha Song <ideal.song@xxxxxxxxxxx>
Signed-off-by: Ingi kim <ingi2.kim@xxxxxxxxxxx>
Signed-off-by: Krzysztof Kozlowski <krzk@xxxxxxxxxx>
Signed-off-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@xxxxxxxxxxx>
Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
---
arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi | 794 ++++++++++++
.../dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi | 23 +
.../dts/exynos/exynos5433-tmu-sensor-conf.dtsi | 22 +
arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi | 296 +++++
arch/arm64/boot/dts/exynos/exynos5433.dtsi | 1356 ++++++++++++++++++++
5 files changed, 2491 insertions(+)
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
create mode 100644 arch/arm64/boot/dts/exynos/exynos5433.dtsi

diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
new file mode 100644
index 000000000000..796881310bf6
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -0,0 +1,794 @@
+/*
+ * Samsung's Exynos5433 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ * Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
+ *
+ * Samsung's Exynos5433 SoC pin-mux and pin-config options are listed as device
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define PIN_PULL_NONE 0
+#define PIN_PULL_DOWN 1
+#define PIN_PULL_UP 3
+
+#define PIN_DRV_LV1 0
+#define PIN_DRV_LV2 2
+#define PIN_DRV_LV3 1
+#define PIN_DRV_LV4 3
+
+#define PIN_IN 0
+#define PIN_OUT 1
+#define PIN_FUNC1 2
+
+#define PIN(_func, _pin, _pull, _drv) \
+ _pin { \
+ samsung,pins = #_pin; \
+ samsung,pin-function = <PIN_ ##_func>; \
+ samsung,pin-pud = <PIN_PULL_ ##_pull>; \
+ samsung,pin-drv = <PIN_DRV_ ##_drv>; \
+ }
+
+&pinctrl_alive {
+ gpa0: gpa0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 0 0>, <GIC_SPI 1 0>, <GIC_SPI 2 0>,
+ <GIC_SPI 3 0>, <GIC_SPI 4 0>, <GIC_SPI 5 0>,
+ <GIC_SPI 6 0>, <GIC_SPI 7 0>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa1: gpa1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ interrupt-parent = <&gic>;
+ interrupts = <GIC_SPI 8 0>, <GIC_SPI 9 0>, <GIC_SPI 10 0>,
+ <GIC_SPI 11 0>, <GIC_SPI 12 0>, <GIC_SPI 13 0>,
+ <GIC_SPI 14 0>, <GIC_SPI 15 0>;
+ #interrupt-cells = <2>;
+ };
+
+ gpa2: gpa2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpa3: gpa3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf1: gpf1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf2: gpf2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf3: gpf3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf4: gpf4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpf5: gpf5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_aud {
+ gpz0: gpz0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpz1: gpz1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ i2s0_bus: i2s0-bus {
+ samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3",
+ "gpz0-4", "gpz0-5", "gpz0-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ pcm0_bus: pcm0-bus {
+ samsung,pins = "gpz1-0", "gpz1-1", "gpz1-2", "gpz1-3";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart_aud_bus: uart-aud-bus {
+ samsung,pins = "gpz1-3", "gpz1-2", "gpz1-1", "gpz1-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_cpif {
+ gpv6: gpv6 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_ese {
+ gpj2: gpj2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_finger {
+ gpd5: gpd5 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ spi2_bus: spi2-bus {
+ samsung,pins = "gpd5-0", "gpd5-2", "gpd5-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c6_bus: hs-i2c6-bus {
+ samsung,pins = "gpd5-3", "gpd5-2";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_fsys {
+ gph1: gph1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpr4: gpr4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpr0: gpr0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpr1: gpr1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpr2: gpr2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpr3: gpr3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ sd0_clk: sd0-clk {
+ samsung,pins = "gpr0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_cmd: sd0-cmd {
+ samsung,pins = "gpr0-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_rdqs: sd0-rdqs {
+ samsung,pins = "gpr0-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_qrdy: sd0-qrdy {
+ samsung,pins = "gpr0-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus1: sd0-bus-width1 {
+ samsung,pins = "gpr1-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus4: sd0-bus-width4 {
+ samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd0_bus8: sd0-bus-width8 {
+ samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_clk: sd1-clk {
+ samsung,pins = "gpr2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_cmd: sd1-cmd {
+ samsung,pins = "gpr2-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus1: sd1-bus-width1 {
+ samsung,pins = "gpr3-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus4: sd1-bus-width4 {
+ samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd1_bus8: sd1-bus-width8 {
+ samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ pcie_bus: pcie_bus {
+ samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ };
+
+ sd2_clk: sd2-clk {
+ samsung,pins = "gpr4-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cmd: sd2-cmd {
+ samsung,pins = "gpr4-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_cd: sd2-cd {
+ samsung,pins = "gpr4-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus1: sd2-bus-width1 {
+ samsung,pins = "gpr4-3";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_bus4: sd2-bus-width4 {
+ samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <3>;
+ };
+
+ sd2_clk_output: sd2-clk-output {
+ samsung,pins = "gpr4-0";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <2>;
+ };
+
+ sd2_cmd_output: sd2-cmd-output {
+ samsung,pins = "gpr4-1";
+ samsung,pin-function = <1>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <2>;
+ };
+};
+
+&pinctrl_imem {
+ gpf0: gpf0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&pinctrl_nfc {
+ gpj0: gpj0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ hs_i2c4_bus: hs-i2c4-bus {
+ samsung,pins = "gpj0-1", "gpj0-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_peric {
+ gpv7: gpv7 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpb0: gpb0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc0: gpc0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc1: gpc1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc2: gpc2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpc3: gpc3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg0: gpg0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd0: gpd0 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd1: gpd1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd2: gpd2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd4: gpd4 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd8: gpd8 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd6: gpd6 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpd7: gpd7 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg1: gpg1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg2: gpg2 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpg3: gpg3 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ hs_i2c8_bus: hs-i2c8-bus {
+ samsung,pins = "gpb0-1", "gpb0-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c9_bus: hs-i2c9-bus {
+ samsung,pins = "gpb0-3", "gpb0-2";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ i2s1_bus: i2s1-bus {
+ samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
+ "gpd4-3", "gpd4-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ pcm1_bus: pcm1-bus {
+ samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
+ "gpd4-3", "gpd4-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ spdif_bus: spdif-bus {
+ samsung,pins = "gpd4-3", "gpd4-4";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <1>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_spi_pin0: fimc-is-spi-pin0 {
+ samsung,pins = "gpc3-3", "gpc3-2", "gpc3-1", "gpc3-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_spi_pin1: fimc-is-spi-pin1 {
+ samsung,pins = "gpc3-7", "gpc3-6", "gpc3-5", "gpc3-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart0_bus: uart0-bus {
+ samsung,pins = "gpd0-3", "gpd0-2", "gpd0-1", "gpd0-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ };
+
+ hs_i2c2_bus: hs-i2c2-bus {
+ samsung,pins = "gpd0-3", "gpd0-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ uart2_bus: uart2-bus {
+ samsung,pins = "gpd1-5", "gpd1-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ };
+
+ uart1_bus: uart1-bus {
+ samsung,pins = "gpd1-3", "gpd1-2", "gpd1-1", "gpd1-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ };
+
+ hs_i2c3_bus: hs-i2c3-bus {
+ samsung,pins = "gpd1-3", "gpd1-2";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c0_bus: hs-i2c0-bus {
+ samsung,pins = "gpd2-1", "gpd2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c1_bus: hs-i2c1-bus {
+ samsung,pins = "gpd2-3", "gpd2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm0_out: pwm0-out {
+ samsung,pins = "gpd2-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm1_out: pwm1-out {
+ samsung,pins = "gpd2-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm2_out: pwm2-out {
+ samsung,pins = "gpd2-6";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ pwm3_out: pwm3-out {
+ samsung,pins = "gpd2-7";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi1_bus: spi1-bus {
+ samsung,pins = "gpd6-2", "gpd6-4", "gpd6-5";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c7_bus: hs-i2c7-bus {
+ samsung,pins = "gpd2-7", "gpd2-6";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi0_bus: spi0-bus {
+ samsung,pins = "gpd8-0", "gpd6-0", "gpd6-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c10_bus: hs-i2c10-bus {
+ samsung,pins = "gpg3-1", "gpg3-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ hs_i2c11_bus: hs-i2c11-bus {
+ samsung,pins = "gpg3-3", "gpg3-2";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi3_bus: spi3-bus {
+ samsung,pins = "gpg3-4", "gpg3-6", "gpg3-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ spi4_bus: spi4-bus {
+ samsung,pins = "gpv7-1", "gpv7-3", "gpv7-4";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_uart: fimc-is-uart {
+ samsung,pins = "gpc1-1", "gpc0-7";
+ samsung,pin-function = <3>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch0_i2c: fimc-is-ch0_i2c {
+ samsung,pins = "gpc2-1", "gpc2-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch0_mclk: fimc-is-ch0_mclk {
+ samsung,pins = "gpd7-0";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch1_i2c: fimc-is-ch1-i2c {
+ samsung,pins = "gpc2-3", "gpc2-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch1_mclk: fimc-is-ch1-mclk {
+ samsung,pins = "gpd7-1";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch2_i2c: fimc-is-ch2-i2c {
+ samsung,pins = "gpc2-5", "gpc2-4";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+
+ fimc_is_ch2_mclk: fimc-is-ch2-mclk {
+ samsung,pins = "gpd7-2";
+ samsung,pin-function = <2>;
+ samsung,pin-pud = <0>;
+ samsung,pin-drv = <0>;
+ };
+};
+
+&pinctrl_touch {
+ gpj1: gpj1 {
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ hs_i2c5_bus: hs-i2c5-bus {
+ samsung,pins = "gpj1-1", "gpj1-0";
+ samsung,pin-function = <4>;
+ samsung,pin-pud = <3>;
+ samsung,pin-drv = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi
new file mode 100644
index 000000000000..9be2978f1b9a
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tmu-g3d-sensor-conf.dtsi
@@ -0,0 +1,23 @@
+/*
+ * Device tree sources for Exynos5433 TMU sensor configuration
+ *
+ * Copyright (c) 2016 Jonghwa Lee <jonghwa3.lee@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <8>;
+samsung,tmu_reference_voltage = <23>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <75>;
+samsung,tmu_min_efuse_value = <40>;
+samsung,tmu_max_efuse_value = <150>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <85>;
+samsung,tmu_default_temp_offset = <50>;
+samsung,tmu_mux_addr = <6>;
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi
new file mode 100644
index 000000000000..125fe58d77ce
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tmu-sensor-conf.dtsi
@@ -0,0 +1,22 @@
+/*
+ * Device tree sources for Exynos5433 TMU sensor configuration
+ *
+ * Copyright (c) 2016 Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/thermal/thermal_exynos.h>
+
+#thermal-sensor-cells = <0>;
+samsung,tmu_gain = <8>;
+samsung,tmu_reference_voltage = <16>;
+samsung,tmu_noise_cancel_mode = <4>;
+samsung,tmu_efuse_value = <75>;
+samsung,tmu_min_efuse_value = <40>;
+samsung,tmu_max_efuse_value = <150>;
+samsung,tmu_first_point_trim = <25>;
+samsung,tmu_second_point_trim = <85>;
+samsung,tmu_default_temp_offset = <50>;
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
new file mode 100644
index 000000000000..ceaa05145b8a
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tmu.dtsi
@@ -0,0 +1,296 @@
+/*
+ * Device tree sources for Exynos5433 thermal zone
+ *
+ * Copyright (c) 2016 Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+thermal-zones {
+ atlas0_thermal: atlas0-thermal {
+ thermal-sensors = <&tmu_atlas0>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ atlas0_alert_0: atlas0-alert-0 {
+ temperature = <65000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_1: atlas0-alert-1 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_2: atlas0-alert-2 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_3: atlas0-alert-3 {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_4: atlas0-alert-4 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_5: atlas0-alert-5 {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas0_alert_6: atlas0-alert-6 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ /* Set maximum frequency as 1800MHz */
+ trip = <&atlas0_alert_0>;
+ cooling-device = <&cpu4 1 2>;
+ };
+ map1 {
+ /* Set maximum frequency as 1700MHz */
+ trip = <&atlas0_alert_1>;
+ cooling-device = <&cpu4 2 3>;
+ };
+ map2 {
+ /* Set maximum frequency as 1600MHz */
+ trip = <&atlas0_alert_2>;
+ cooling-device = <&cpu4 3 4>;
+ };
+ map3 {
+ /* Set maximum frequency as 1500MHz */
+ trip = <&atlas0_alert_3>;
+ cooling-device = <&cpu4 4 5>;
+ };
+ map4 {
+ /* Set maximum frequency as 1400MHz */
+ trip = <&atlas0_alert_4>;
+ cooling-device = <&cpu4 5 7>;
+ };
+ map5 {
+ /* Set maximum frequencyas 1200MHz */
+ trip = <&atlas0_alert_5>;
+ cooling-device = <&cpu4 7 9>;
+ };
+ map6 {
+ /* Set maximum frequency as 1000MHz */
+ trip = <&atlas0_alert_6>;
+ cooling-device = <&cpu4 9 14>;
+ };
+ };
+ };
+
+ atlas1_thermal: atlas1-thermal {
+ thermal-sensors = <&tmu_atlas1>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ atlas1_alert_0: atlas1-alert-0 {
+ temperature = <65000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_1: atlas1-alert-1 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_2: atlas1-alert-2 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_3: atlas1-alert-3 {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_4: atlas1-alert-4 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_5: atlas1-alert-5 {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ atlas1_alert_6: atlas1-alert-6 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ };
+ };
+
+ g3d_thermal: g3d-thermal {
+ thermal-sensors = <&tmu_g3d>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ g3d_alert_0: g3d-alert-0 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_1: g3d-alert-1 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_2: g3d-alert-2 {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_3: g3d-alert-3 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_4: g3d-alert-4 {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_5: g3d-alert-5 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ g3d_alert_6: g3d-alert-6 {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ };
+ };
+
+ apollo_thermal: apollo-thermal {
+ thermal-sensors = <&tmu_apollo>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ apollo_alert_0: apollo-alert-0 {
+ temperature = <65000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_1: apollo-alert-1 {
+ temperature = <70000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_2: apollo-alert-2 {
+ temperature = <75000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_3: apollo-alert-3 {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_4: apollo-alert-4 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_5: apollo-alert-5 {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ apollo_alert_6: apollo-alert-6 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map0 {
+ /* Set maximum frequency as 1200MHz */
+ trip = <&apollo_alert_2>;
+ cooling-device = <&cpu0 1 2>;
+ };
+ map1 {
+ /* Set maximum frequency as 1100MHz */
+ trip = <&apollo_alert_3>;
+ cooling-device = <&cpu0 2 3>;
+ };
+ map2 {
+ /* Set maximum frequency as 1000MHz */
+ trip = <&apollo_alert_4>;
+ cooling-device = <&cpu0 3 4>;
+ };
+ map3 {
+ /* Set maximum frequency as 900MHz */
+ trip = <&apollo_alert_5>;
+ cooling-device = <&cpu0 4 5>;
+ };
+ map4 {
+ /* Set maximum frequency as 800MHz */
+ trip = <&apollo_alert_6>;
+ cooling-device = <&cpu0 5 9>;
+ };
+ };
+ };
+
+ isp_thermal: isp-thermal {
+ thermal-sensors = <&tmu_isp>;
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ trips {
+ isp_alert_0: isp-alert-0 {
+ temperature = <80000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_1: isp-alert-1 {
+ temperature = <85000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_2: isp-alert-2 {
+ temperature = <90000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_3: isp-alert-3 {
+ temperature = <95000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_4: isp-alert-4 {
+ temperature = <100000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_5: isp-alert-5 {
+ temperature = <105000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ isp_alert_6: isp-alert-6 {
+ temperature = <110000>; /* millicelsius */
+ hysteresis = <1000>; /* millicelsius */
+ type = "active";
+ };
+ };
+ };
+};
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
new file mode 100644
index 000000000000..1188630823a7
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -0,0 +1,1356 @@
+/*
+ * Samsung's Exynos5433 SoC device tree source
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *
+ * Samsung's Exynos5433 SoC device nodes are listed in this file.
+ * Exynos5433 based board files can include this file and provide
+ * values for board specific bindings.
+ *
+ * Note: This file does not include device nodes for all the controllers in
+ * Exynos5433 SoC. As device tree coverage for Exynos5433 increases,
+ * additional nodes can be added to this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/clock/exynos5433.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ compatible = "samsung,exynos5433";
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@100 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x100>;
+ clock-frequency = <1300000000>;
+ clocks = <&cmu_apollo CLK_SCLK_APOLLO>;
+ clock-names = "apolloclk";
+ operating-points-v2 = <&cluster_a53_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu1: cpu@101 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x101>;
+ clock-frequency = <1300000000>;
+ operating-points-v2 = <&cluster_a53_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu2: cpu@102 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x102>;
+ clock-frequency = <1300000000>;
+ operating-points-v2 = <&cluster_a53_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu3: cpu@103 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x103>;
+ clock-frequency = <1300000000>;
+ operating-points-v2 = <&cluster_a53_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu4: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a57", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x0>;
+ clock-frequency = <1900000000>;
+ clocks = <&cmu_atlas CLK_SCLK_ATLAS>;
+ clock-names = "atlasclk";
+ operating-points-v2 = <&cluster_a57_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu5: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a57", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x1>;
+ clock-frequency = <1900000000>;
+ operating-points-v2 = <&cluster_a57_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu6: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a57", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x2>;
+ clock-frequency = <1900000000>;
+ operating-points-v2 = <&cluster_a57_opp_table>;
+ #cooling-cells = <2>;
+ };
+
+ cpu7: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a57", "arm,armv8";
+ enable-method = "psci";
+ reg = <0x3>;
+ clock-frequency = <1900000000>;
+ operating-points-v2 = <&cluster_a57_opp_table>;
+ #cooling-cells = <2>;
+ };
+ };
+
+ cluster_a53_opp_table: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp@400000000 {
+ opp-hz = /bits/ 64 <400000000>;
+ opp-microvolt = <900000>;
+ };
+ opp@500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <925000>;
+ };
+ opp@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <950000>;
+ };
+ opp@700000000 {
+ opp-hz = /bits/ 64 <700000000>;
+ opp-microvolt = <975000>;
+ };
+ opp@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <1000000>;
+ };
+ opp@900000000 {
+ opp-hz = /bits/ 64 <900000000>;
+ opp-microvolt = <1050000>;
+ };
+ opp@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <1075000>;
+ };
+ opp@1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1112500>;
+ };
+ opp@1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1112500>;
+ };
+ opp@1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1150000>;
+ };
+ };
+
+ cluster_a57_opp_table: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp@500000000 {
+ opp-hz = /bits/ 64 <500000000>;
+ opp-microvolt = <900000>;
+ };
+ opp@600000000 {
+ opp-hz = /bits/ 64 <600000000>;
+ opp-microvolt = <900000>;
+ };
+ opp@700000000 {
+ opp-hz = /bits/ 64 <700000000>;
+ opp-microvolt = <912500>;
+ };
+ opp@800000000 {
+ opp-hz = /bits/ 64 <800000000>;
+ opp-microvolt = <912500>;
+ };
+ opp@900000000 {
+ opp-hz = /bits/ 64 <900000000>;
+ opp-microvolt = <937500>;
+ };
+ opp@1000000000 {
+ opp-hz = /bits/ 64 <1000000000>;
+ opp-microvolt = <975000>;
+ };
+ opp@1100000000 {
+ opp-hz = /bits/ 64 <1100000000>;
+ opp-microvolt = <1012500>;
+ };
+ opp@1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1037500>;
+ };
+ opp@1300000000 {
+ opp-hz = /bits/ 64 <1300000000>;
+ opp-microvolt = <1062500>;
+ };
+ opp@1400000000 {
+ opp-hz = /bits/ 64 <1400000000>;
+ opp-microvolt = <1087500>;
+ };
+ opp@1500000000 {
+ opp-hz = /bits/ 64 <1500000000>;
+ opp-microvolt = <1125000>;
+ };
+ opp@1600000000 {
+ opp-hz = /bits/ 64 <1600000000>;
+ opp-microvolt = <1137500>;
+ };
+ opp@1700000000 {
+ opp-hz = /bits/ 64 <1700000000>;
+ opp-microvolt = <1175000>;
+ };
+ opp@1800000000 {
+ opp-hz = /bits/ 64 <1800000000>;
+ opp-microvolt = <1212500>;
+ };
+ opp@1900000000 {
+ opp-hz = /bits/ 64 <1900000000>;
+ opp-microvolt = <1262500>;
+ };
+ };
+
+ psci {
+ compatible = "arm,psci";
+ method = "smc";
+ cpu_off = <0x84000002>;
+ cpu_on = <0xC4000003>;
+ };
+
+ reboot: syscon-reboot {
+ compatible = "syscon-reboot";
+ regmap = <&pmu_system_controller>;
+ offset = <0x400>; /* SWRESET */
+ mask = <0x1>;
+ };
+
+ soc: soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x18000000>;
+
+ chipid@10000000 {
+ compatible = "samsung,exynos4210-chipid";
+ reg = <0x10000000 0x100>;
+ };
+
+ xxti: xxti {
+ compatible = "fixed-clock";
+ clock-output-names = "oscclk";
+ #clock-cells = <0>;
+ };
+
+ cmu_top: clock-controller@10030000 {
+ compatible = "samsung,exynos5433-cmu-top";
+ reg = <0x10030000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_mphy_pll",
+ "sclk_mfc_pll",
+ "sclk_bus_pll";
+ clocks = <&xxti>,
+ <&cmu_cpif CLK_SCLK_MPHY_PLL>,
+ <&cmu_mif CLK_SCLK_MFC_PLL>,
+ <&cmu_mif CLK_SCLK_BUS_PLL>;
+ };
+
+ cmu_cpif: clock-controller@10fc0000 {
+ compatible = "samsung,exynos5433-cmu-cpif";
+ reg = <0x10fc0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk";
+ clocks = <&xxti>;
+ };
+
+ cmu_mif: clock-controller@105b0000 {
+ compatible = "samsung,exynos5433-cmu-mif";
+ reg = <0x105b0000 0x2000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_mphy_pll";
+ clocks = <&xxti>,
+ <&cmu_cpif CLK_SCLK_MPHY_PLL>;
+ };
+
+ cmu_peric: clock-controller@14c80000 {
+ compatible = "samsung,exynos5433-cmu-peric";
+ reg = <0x14c80000 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ cmu_peris: clock-controller@0x10040000 {
+ compatible = "samsung,exynos5433-cmu-peris";
+ reg = <0x10040000 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ cmu_fsys: clock-controller@156e0000 {
+ compatible = "samsung,exynos5433-cmu-fsys";
+ reg = <0x156e0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_ufs_mphy",
+ "div_aclk_fsys_200",
+ "sclk_pcie_100_fsys",
+ "sclk_ufsunipro_fsys",
+ "sclk_mmc2_fsys",
+ "sclk_mmc1_fsys",
+ "sclk_mmc0_fsys",
+ "sclk_usbhost30_fsys",
+ "sclk_usbdrd30_fsys";
+ clocks = <&xxti>,
+ <&cmu_cpif CLK_SCLK_UFS_MPHY>,
+ <&cmu_top CLK_DIV_ACLK_FSYS_200>,
+ <&cmu_top CLK_SCLK_PCIE_100_FSYS>,
+ <&cmu_top CLK_SCLK_UFSUNIPRO_FSYS>,
+ <&cmu_top CLK_SCLK_MMC2_FSYS>,
+ <&cmu_top CLK_SCLK_MMC1_FSYS>,
+ <&cmu_top CLK_SCLK_MMC0_FSYS>,
+ <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
+ <&cmu_top CLK_SCLK_USBDRD30_FSYS>;
+ };
+
+ cmu_g2d: clock-controller@12460000 {
+ compatible = "samsung,exynos5433-cmu-g2d";
+ reg = <0x12460000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "aclk_g2d_266",
+ "aclk_g2d_400";
+ clocks = <&xxti>,
+ <&cmu_top CLK_ACLK_G2D_266>,
+ <&cmu_top CLK_ACLK_G2D_400>;
+ };
+
+ cmu_disp: clock-controller@13b90000 {
+ compatible = "samsung,exynos5433-cmu-disp";
+ reg = <0x13b90000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_dsim1_disp",
+ "sclk_dsim0_disp",
+ "sclk_dsd_disp",
+ "sclk_decon_tv_eclk_disp",
+ "sclk_decon_vclk_disp",
+ "sclk_decon_eclk_disp",
+ "sclk_decon_tv_vclk_disp",
+ "aclk_disp_333";
+ clocks = <&xxti>,
+ <&cmu_mif CLK_SCLK_DSIM1_DISP>,
+ <&cmu_mif CLK_SCLK_DSIM0_DISP>,
+ <&cmu_mif CLK_SCLK_DSD_DISP>,
+ <&cmu_mif CLK_SCLK_DECON_TV_ECLK_DISP>,
+ <&cmu_mif CLK_SCLK_DECON_VCLK_DISP>,
+ <&cmu_mif CLK_SCLK_DECON_ECLK_DISP>,
+ <&cmu_mif CLK_SCLK_DECON_TV_VCLK_DISP>,
+ <&cmu_mif CLK_ACLK_DISP_333>;
+ };
+
+ cmu_aud: clock-controller@114c0000 {
+ compatible = "samsung,exynos5433-cmu-aud";
+ reg = <0x114c0000 0x1000>;
+ #clock-cells = <1>;
+ };
+
+ cmu_bus0: clock-controller@13600000 {
+ compatible = "samsung,exynos5433-cmu-bus0";
+ reg = <0x13600000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "aclk_bus0_400";
+ clocks = <&cmu_top CLK_ACLK_BUS0_400>;
+ };
+
+ cmu_bus1: clock-controller@14800000 {
+ compatible = "samsung,exynos5433-cmu-bus1";
+ reg = <0x14800000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "aclk_bus1_400";
+ clocks = <&cmu_top CLK_ACLK_BUS1_400>;
+ };
+
+ cmu_bus2: clock-controller@13400000 {
+ compatible = "samsung,exynos5433-cmu-bus2";
+ reg = <0x13400000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "aclk_bus2_400";
+ clocks = <&xxti>, <&cmu_mif CLK_ACLK_BUS2_400>;
+ };
+
+ cmu_g3d: clock-controller@14aa0000 {
+ compatible = "samsung,exynos5433-cmu-g3d";
+ reg = <0x14aa0000 0x2000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "aclk_g3d_400";
+ clocks = <&xxti>, <&cmu_top CLK_ACLK_G3D_400>;
+ };
+
+ cmu_gscl: clock-controller@13cf0000 {
+ compatible = "samsung,exynos5433-cmu-gscl";
+ reg = <0x13cf0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "aclk_gscl_111",
+ "aclk_gscl_333";
+ clocks = <&xxti>,
+ <&cmu_top CLK_ACLK_GSCL_111>,
+ <&cmu_top CLK_ACLK_GSCL_333>;
+ };
+
+ cmu_apollo: clock-controller@11900000 {
+ compatible = "samsung,exynos5433-cmu-apollo";
+ reg = <0x11900000 0x2000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "sclk_bus_pll_apollo";
+ clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_APOLLO>;
+ };
+
+ cmu_atlas: clock-controller@11800000 {
+ compatible = "samsung,exynos5433-cmu-atlas";
+ reg = <0x11800000 0x2000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "sclk_bus_pll_atlas";
+ clocks = <&xxti>, <&cmu_mif CLK_SCLK_BUS_PLL_ATLAS>;
+ };
+
+ cmu_mscl: clock-controller@105d0000 {
+ compatible = "samsung,exynos5433-cmu-mscl";
+ reg = <0x150d0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_jpeg_mscl",
+ "aclk_mscl_400";
+ clocks = <&xxti>,
+ <&cmu_top CLK_SCLK_JPEG_MSCL>,
+ <&cmu_top CLK_ACLK_MSCL_400>;
+ };
+
+ cmu_mfc: clock-controller@15280000 {
+ compatible = "samsung,exynos5433-cmu-mfc";
+ reg = <0x15280000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "aclk_mfc_400";
+ clocks = <&xxti>, <&cmu_top CLK_ACLK_MFC_400>;
+ };
+
+ cmu_hevc: clock-controller@14f80000 {
+ compatible = "samsung,exynos5433-cmu-hevc";
+ reg = <0x14f80000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk", "aclk_hevc_400";
+ clocks = <&xxti>, <&cmu_top CLK_ACLK_HEVC_400>;
+ };
+
+ cmu_isp: clock-controller@146d0000 {
+ compatible = "samsung,exynos5433-cmu-isp";
+ reg = <0x146d0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "aclk_isp_dis_400",
+ "aclk_isp_400";
+ clocks = <&xxti>,
+ <&cmu_top CLK_ACLK_ISP_DIS_400>,
+ <&cmu_top CLK_ACLK_ISP_400>;
+ };
+
+ cmu_cam0: clock-controller@120d0000 {
+ compatible = "samsung,exynos5433-cmu-cam0";
+ reg = <0x120d0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "aclk_cam0_333",
+ "aclk_cam0_400",
+ "aclk_cam0_552";
+ clocks = <&xxti>,
+ <&cmu_top CLK_ACLK_CAM0_333>,
+ <&cmu_top CLK_ACLK_CAM0_400>,
+ <&cmu_top CLK_ACLK_CAM0_552>;
+ };
+
+ cmu_cam1: clock-controller@145d0000 {
+ compatible = "samsung,exynos5433-cmu-cam1";
+ reg = <0x145d0000 0x1000>;
+ #clock-cells = <1>;
+
+ clock-names = "oscclk",
+ "sclk_isp_uart_cam1",
+ "sclk_isp_spi1_cam1",
+ "sclk_isp_spi0_cam1",
+ "aclk_cam1_333",
+ "aclk_cam1_400",
+ "aclk_cam1_552";
+ clocks = <&xxti>,
+ <&cmu_top CLK_SCLK_ISP_UART_CAM1>,
+ <&cmu_top CLK_SCLK_ISP_SPI1_CAM1>,
+ <&cmu_top CLK_SCLK_ISP_SPI0_CAM1>,
+ <&cmu_top CLK_ACLK_CAM1_333>,
+ <&cmu_top CLK_ACLK_CAM1_400>,
+ <&cmu_top CLK_ACLK_CAM1_552>;
+ };
+
+ tmu_atlas0: tmu@10060000 {
+ compatible = "samsung,exynos5433-tmu";
+ reg = <0x10060000 0x200>;
+ interrupts = <GIC_SPI 95 0>;
+ clocks = <&cmu_peris CLK_PCLK_TMU0_APBIF>,
+ <&cmu_peris CLK_SCLK_TMU0>;
+ clock-names = "tmu_apbif", "tmu_sclk";
+ #include "exynos5433-tmu-sensor-conf.dtsi"
+ status = "disabled";
+ };
+
+ tmu_atlas1: tmu@10068000 {
+ compatible = "samsung,exynos5433-tmu";
+ reg = <0x10068000 0x200>;
+ interrupts = <GIC_SPI 96 0>;
+ clocks = <&cmu_peris CLK_PCLK_TMU0_APBIF>,
+ <&cmu_peris CLK_SCLK_TMU0>;
+ clock-names = "tmu_apbif", "tmu_sclk";
+ #include "exynos5433-tmu-sensor-conf.dtsi"
+ status = "disabled";
+ };
+
+ tmu_g3d: tmu@10070000 {
+ compatible = "samsung,exynos5433-tmu";
+ reg = <0x10070000 0x200>;
+ interrupts = <GIC_SPI 99 0>;
+ clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
+ <&cmu_peris CLK_SCLK_TMU1>;
+ clock-names = "tmu_apbif", "tmu_sclk";
+ #include "exynos5433-tmu-g3d-sensor-conf.dtsi"
+ status = "disabled";
+ };
+
+ tmu_apollo: tmu@10078000 {
+ compatible = "samsung,exynos5433-tmu";
+ reg = <0x10078000 0x200>;
+ interrupts = <GIC_SPI 115 0>;
+ clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
+ <&cmu_peris CLK_SCLK_TMU1>;
+ clock-names = "tmu_apbif", "tmu_sclk";
+ #include "exynos5433-tmu-sensor-conf.dtsi"
+ status = "disabled";
+ };
+
+ tmu_isp: tmu@1007c000 {
+ compatible = "samsung,exynos5433-tmu";
+ reg = <0x1007c000 0x200>;
+ interrupts = <GIC_SPI 94 0>;
+ clocks = <&cmu_peris CLK_PCLK_TMU1_APBIF>,
+ <&cmu_peris CLK_SCLK_TMU1>;
+ clock-names = "tmu_apbif", "tmu_sclk";
+ #include "exynos5433-tmu-sensor-conf.dtsi"
+ status = "disabled";
+ };
+
+ mct@101c0000 {
+ compatible = "samsung,exynos4210-mct";
+ reg = <0x101c0000 0x800>;
+ interrupts = <GIC_SPI 102 0>, <GIC_SPI 103 0>,
+ <GIC_SPI 104 0>, <GIC_SPI 105 0>,
+ <GIC_SPI 106 0>, <GIC_SPI 107 0>,
+ <GIC_SPI 108 0>, <GIC_SPI 109 0>,
+ <GIC_SPI 110 0>, <GIC_SPI 111 0>,
+ <GIC_SPI 112 0>, <GIC_SPI 113 0>;
+ clocks = <&xxti>, <&cmu_peris CLK_PCLK_MCT>;
+ clock-names = "fin_pll", "mct";
+ };
+
+ pinctrl_alive: pinctrl@10580000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x10580000 0x1a20>, <0x11090000 0x100>;
+
+ wakeup-interrupt-controller {
+ compatible = "samsung,exynos7-wakeup-eint";
+ interrupts = <GIC_SPI 16 0>;
+ };
+ };
+
+ pinctrl_aud: pinctrl@114b0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x114b0000 0x1000>;
+ interrupts = <GIC_SPI 68 0>;
+ };
+
+ pinctrl_cpif: pinctrl@10fe0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x10fe0000 0x1000>;
+ interrupts = <GIC_SPI 179 0>;
+ };
+
+ pinctrl_ese: pinctrl@14ca0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x14ca0000 0x1000>;
+ interrupts = <GIC_SPI 413 0>;
+ };
+
+ pinctrl_finger: pinctrl@14cb0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x14cb0000 0x1000>;
+ interrupts = <GIC_SPI 414 0>;
+ };
+
+ pinctrl_fsys: pinctrl@15690000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x15690000 0x1000>;
+ interrupts = <GIC_SPI 229 0>;
+ };
+
+ pinctrl_imem: pinctrl@11090000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x11090000 0x1000>;
+ interrupts = <GIC_SPI 325 0>;
+ };
+
+ pinctrl_nfc: pinctrl@14cd0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x14cd0000 0x1000>;
+ interrupts = <GIC_SPI 441 0>;
+ };
+
+ pinctrl_peric: pinctrl@14cc0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x14cc0000 0x1100>;
+ interrupts = <GIC_SPI 440 0>;
+ };
+
+ pinctrl_touch: pinctrl@14ce0000 {
+ compatible = "samsung,exynos5433-pinctrl";
+ reg = <0x14ce0000 0x1100>;
+ interrupts = <GIC_SPI 442 0>;
+ };
+
+ pmu_system_controller: system-controller@105c0000 {
+ compatible = "samsung,exynos5433-pmu", "syscon";
+ reg = <0x105c0000 0x5008>;
+ #clock-cells = <1>;
+ clock-names = "clkout16";
+ clocks = <&xxti>;
+ };
+
+ gic: interrupt-controller@11001000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x11001000 0x1000>,
+ <0x11002000 0x2000>,
+ <0x11004000 0x2000>,
+ <0x11006000 0x2000>;
+ interrupts = <GIC_PPI 9 0xf04>;
+ };
+
+ mipi_phy: video-phy@105c0710 {
+ compatible = "samsung,exynos5433-mipi-video-phy";
+ #phy-cells = <1>;
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ samsung,cam0-sysreg = <&syscon_cam0>;
+ samsung,cam1-sysreg = <&syscon_cam1>;
+ samsung,disp-sysreg = <&syscon_disp>;
+ };
+
+ decon: decon@13800000 {
+ compatible = "samsung,exynos5433-decon";
+ reg = <0x13800000 0x2104>;
+ clocks = <&cmu_disp CLK_PCLK_DECON>,
+ <&cmu_disp CLK_ACLK_DECON>,
+ <&cmu_disp CLK_ACLK_SMMU_DECON0X>,
+ <&cmu_disp CLK_ACLK_XIU_DECON0X>,
+ <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
+ <&cmu_disp CLK_SCLK_DECON_VCLK>,
+ <&cmu_disp CLK_SCLK_DECON_ECLK>;
+ clock-names = "pclk", "aclk_decon", "aclk_smmu_decon0x",
+ "aclk_xiu_decon0x", "pclk_smmu_decon0x",
+ "sclk_decon_vclk", "sclk_decon_eclk";
+ interrupt-names = "fifo", "vsync", "lcd_sys";
+ interrupts = <GIC_SPI 201 0>, <GIC_SPI 202 0>,
+ <GIC_SPI 203 0>;
+ samsung,disp-sysreg = <&syscon_disp>;
+ status = "disabled";
+ iommus = <&sysmmu_decon0x>, <&sysmmu_decon1x>;
+ iommu-names = "m0", "m1";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ decon_to_mic: endpoint {
+ remote-endpoint =
+ <&mic_to_decon>;
+ };
+ };
+ };
+ };
+
+ dsi: dsi@13900000 {
+ compatible = "samsung,exynos5433-mipi-dsi";
+ reg = <0x13900000 0xC0>;
+ interrupts = <GIC_SPI 205 0>;
+ phys = <&mipi_phy 1>;
+ phy-names = "dsim";
+ clocks = <&cmu_disp CLK_PCLK_DSIM0>,
+ <&cmu_disp CLK_PHYCLK_MIPIDPHY0_BITCLKDIV8>,
+ <&cmu_disp CLK_PHYCLK_MIPIDPHY0_RXCLKESC0>,
+ <&cmu_disp CLK_SCLK_RGB_VCLK_TO_DSIM0>,
+ <&cmu_disp CLK_SCLK_DSIM0>;
+ clock-names = "bus_clk",
+ "phyclk_mipidphy0_bitclkdiv8",
+ "phyclk_mipidphy0_rxclkesc0",
+ "sclk_rgb_vclk_to_dsim0",
+ "sclk_mipi";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dsi_to_mic: endpoint {
+ remote-endpoint = <&mic_to_dsi>;
+ };
+ };
+ };
+ };
+
+ mic: mic@13930000 {
+ compatible = "samsung,exynos5433-mic";
+ reg = <0x13930000 0x48>;
+ clocks = <&cmu_disp CLK_PCLK_MIC0>,
+ <&cmu_disp CLK_SCLK_RGB_VCLK_TO_MIC0>;
+ clock-names = "pclk_mic0", "sclk_rgb_vclk_to_mic0";
+ samsung,disp-syscon = <&syscon_disp>;
+ status = "disabled";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ mic_to_decon: endpoint {
+ remote-endpoint =
+ <&decon_to_mic>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ mic_to_dsi: endpoint {
+ remote-endpoint = <&dsi_to_mic>;
+ };
+ };
+ };
+ };
+
+ syscon_disp: syscon@13b80000 {
+ compatible = "syscon";
+ reg = <0x13b80000 0x1010>;
+ };
+
+ syscon_cam0: syscon@120f0000 {
+ compatible = "syscon";
+ reg = <0x120f0000 0x1020>;
+ };
+
+ syscon_cam1: syscon@145f0000 {
+ compatible = "syscon";
+ reg = <0x145f0000 0x1038>;
+ };
+
+ sysmmu_decon0x: sysmmu@0x13a00000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13a00000 0x1000>;
+ interrupts = <GIC_SPI 192 0>;
+ clock-names = "pclk", "aclk";
+ clocks = <&cmu_disp CLK_PCLK_SMMU_DECON0X>,
+ <&cmu_disp CLK_ACLK_SMMU_DECON0X>;
+ #iommu-cells = <0>;
+ };
+
+ sysmmu_decon1x: sysmmu@0x13a10000 {
+ compatible = "samsung,exynos-sysmmu";
+ reg = <0x13a10000 0x1000>;
+ interrupts = <GIC_SPI 194 0>;
+ clock-names = "pclk", "aclk";
+ clocks = <&cmu_disp CLK_PCLK_SMMU_DECON1X>,
+ <&cmu_disp CLK_ACLK_SMMU_DECON1X>;
+ #iommu-cells = <0>;
+ };
+
+ serial_0: serial@14c10000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x14c10000 0x100>;
+ interrupts = <GIC_SPI 421 0>;
+ clocks = <&cmu_peric CLK_PCLK_UART0>,
+ <&cmu_peric CLK_SCLK_UART0>;
+ clock-names = "uart", "clk_uart_baud0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_bus>;
+ status = "disabled";
+ };
+
+ serial_1: serial@14c20000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x14c20000 0x100>;
+ interrupts = <GIC_SPI 422 0>;
+ clocks = <&cmu_peric CLK_PCLK_UART1>,
+ <&cmu_peric CLK_SCLK_UART1>;
+ clock-names = "uart", "clk_uart_baud0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_bus>;
+ status = "disabled";
+ };
+
+ serial_2: serial@14c30000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x14c30000 0x100>;
+ interrupts = <GIC_SPI 423 0>;
+ clocks = <&cmu_peric CLK_PCLK_UART2>,
+ <&cmu_peric CLK_SCLK_UART2>;
+ clock-names = "uart", "clk_uart_baud0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_bus>;
+ status = "disabled";
+ };
+
+ spi_0: spi@14d20000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d20000 0x100>;
+ interrupts = <GIC_SPI 432 0>;
+ dmas = <&pdma0 9>, <&pdma0 8>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI0>,
+ <&cmu_peric CLK_SCLK_SPI0>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI0>;
+ clock-names = "spi", "spi_busclk0", "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_bus>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi_1: spi@14d30000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d30000 0x100>;
+ interrupts = <GIC_SPI 433 0>;
+ dmas = <&pdma0 11>, <&pdma0 10>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_SPI1>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI1>;
+ clock-names = "spi", "spi_busclk0", "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_bus>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi_2: spi@14d40000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d40000 0x100>;
+ interrupts = <GIC_SPI 434 0>;
+ dmas = <&pdma0 13>, <&pdma0 12>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI2>,
+ <&cmu_peric CLK_SCLK_SPI2>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI2>;
+ clock-names = "spi", "spi_busclk0", "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2_bus>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi_3: spi@14d50000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d50000 0x100>;
+ interrupts = <GIC_SPI 447 0>;
+ dmas = <&pdma0 23>, <&pdma0 22>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI3>,
+ <&cmu_peric CLK_SCLK_SPI3>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI3>;
+ clock-names = "spi", "spi_busclk0", "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi3_bus>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ spi_4: spi@14d00000 {
+ compatible = "samsung,exynos5433-spi";
+ reg = <0x14d00000 0x100>;
+ interrupts = <GIC_SPI 412 0>;
+ dmas = <&pdma0 25>, <&pdma0 24>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_peric CLK_PCLK_SPI4>,
+ <&cmu_peric CLK_SCLK_SPI4>,
+ <&cmu_peric CLK_SCLK_IOCLK_SPI4>;
+ clock-names = "spi", "spi_busclk0", "spi_ioclk";
+ samsung,spi-src-clk = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi4_bus>;
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ adc: adc@14d10000 {
+ compatible = "samsung,exynos7-adc";
+ reg = <0x14d10000 0x100>;
+ interrupts = <GIC_SPI 438 0>;
+ clock-names = "adc";
+ clocks = <&cmu_peric CLK_PCLK_ADCIF>;
+ #io-channel-cells = <1>;
+ io-channel-ranges;
+ status = "disabled";
+ };
+
+ pwm: pwm@14dd0000 {
+ compatible = "samsung,exynos4210-pwm";
+ reg = <0x14dd0000 0x100>;
+ interrupts = <GIC_SPI 416 0>, <GIC_SPI 417 0>,
+ <GIC_SPI 418 0>, <GIC_SPI 419 0>,
+ <GIC_SPI 420 0>;
+ samsung,pwm-outputs = <0>, <1>, <2>, <3>;
+ clocks = <&cmu_peric CLK_PCLK_PWM>;
+ clock-names = "timers";
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ hsi2c_0: hsi2c@14e40000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14e40000 0x1000>;
+ interrupts = <GIC_SPI 428 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c0_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C0>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_1: hsi2c@14e50000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14e50000 0x1000>;
+ interrupts = <GIC_SPI 429 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c1_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C1>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_2: hsi2c@14e60000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14e60000 0x1000>;
+ interrupts = <GIC_SPI 430 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c2_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C2>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_3: hsi2c@14e70000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14e70000 0x1000>;
+ interrupts = <GIC_SPI 431 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c3_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C3>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_4: hsi2c@14ec0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14ec0000 0x1000>;
+ interrupts = <GIC_SPI 424 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c4_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C4>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_5: hsi2c@14ed0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14ed0000 0x1000>;
+ interrupts = <GIC_SPI 425 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c5_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C5>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_6: hsi2c@14ee0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14ee0000 0x1000>;
+ interrupts = <GIC_SPI 426 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c6_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C6>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_7: hsi2c@14ef0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14ef0000 0x1000>;
+ interrupts = <GIC_SPI 427 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c7_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C7>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_8: hsi2c@14d90000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14d90000 0x1000>;
+ interrupts = <GIC_SPI 443 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c8_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C8>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_9: hsi2c@14da0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14da0000 0x1000>;
+ interrupts = <GIC_SPI 444 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c9_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C9>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_10: hsi2c@14de0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14de0000 0x1000>;
+ interrupts = <GIC_SPI 445 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c10_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C10>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ hsi2c_11: hsi2c@14df0000 {
+ compatible = "samsung,exynos7-hsi2c";
+ reg = <0x14df0000 0x1000>;
+ interrupts = <GIC_SPI 446 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hs_i2c11_bus>;
+ clocks = <&cmu_peric CLK_PCLK_HSI2C11>;
+ clock-names = "hsi2c";
+ status = "disabled";
+ };
+
+ usbdrd30: usb@15400000 {
+ compatible = "samsung,exynos5250-dwusb3";
+ clocks = <&cmu_fsys CLK_ACLK_USBDRD30>,
+ <&cmu_fsys CLK_SCLK_USBDRD30>;
+ clock-names = "usbdrd30", "usbdrd30_susp_clk";
+ assigned-clocks =
+ <&cmu_fsys CLK_MOUT_SCLK_USBDRD30_USER>,
+ <&cmu_top CLK_MOUT_SCLK_USBDRD30>,
+ <&cmu_top CLK_DIV_SCLK_USBDRD30>;
+ assigned-clock-parents =
+ <&cmu_top CLK_SCLK_USBDRD30_FSYS>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>;
+ assigned-clock-rates = <0>, <0>, <66700000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ dwc3@15400000 {
+ compatible = "snps,dwc3";
+ reg = <0x15400000 0x10000>;
+ interrupts = <GIC_SPI 231 0>;
+ phys = <&usbdrd30_phy 0>, <&usbdrd30_phy 1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ usbdrd30_phy: phy@15500000 {
+ compatible = "samsung,exynos5433-usbdrd-phy";
+ reg = <0x15500000 0x100>;
+ clocks = <&cmu_fsys CLK_ACLK_USBDRD30>, <&xxti>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK>,
+ <&cmu_fsys CLK_SCLK_USBDRD30>;
+ clock-names = "phy", "ref", "phy_utmi", "phy_pipe",
+ "itp";
+ assigned-clocks =
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_USER>;
+ assigned-clock-parents =
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBDRD30_UDRD30_PHYCLOCK_PHY>;
+ #phy-cells = <1>;
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ status = "disabled";
+ };
+
+ usbhost30_phy: phy@15580000 {
+ compatible = "samsung,exynos5433-usbdrd-phy";
+ reg = <0x15580000 0x100>;
+ clocks = <&cmu_fsys CLK_ACLK_USBHOST30>, <&xxti>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK>,
+ <&cmu_fsys CLK_SCLK_USBHOST30>;
+ clock-names = "phy", "ref", "phy_utmi", "phy_pipe",
+ "itp";
+ assigned-clocks =
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_USER>,
+ <&cmu_fsys CLK_MOUT_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_USER>;
+ assigned-clock-parents =
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PIPE_PCLK_PHY>,
+ <&cmu_fsys CLK_PHYCLK_USBHOST30_UHOST30_PHYCLOCK_PHY>;
+ #phy-cells = <1>;
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ status = "disabled";
+ };
+
+ usbhost30: usb@15a00000 {
+ compatible = "samsung,exynos5250-dwusb3";
+ clocks = <&cmu_fsys CLK_ACLK_USBHOST30>,
+ <&cmu_fsys CLK_SCLK_USBHOST30>;
+ clock-names = "usbdrd30", "usbdrd30_susp_clk";
+ assigned-clocks =
+ <&cmu_fsys CLK_MOUT_SCLK_USBHOST30_USER>,
+ <&cmu_top CLK_MOUT_SCLK_USBHOST30>,
+ <&cmu_top CLK_DIV_SCLK_USBHOST30>;
+ assigned-clock-parents =
+ <&cmu_top CLK_SCLK_USBHOST30_FSYS>,
+ <&cmu_top CLK_MOUT_BUS_PLL_USER>;
+ assigned-clock-rates = <0>, <0>, <66700000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+ status = "disabled";
+
+ usbdrd_dwc3_0: dwc3@15a00000 {
+ compatible = "snps,dwc3";
+ reg = <0x15a00000 0x10000>;
+ interrupts = <GIC_SPI 244 0>;
+ phys = <&usbhost30_phy 0>, <&usbhost30_phy 1>;
+ phy-names = "usb2-phy", "usb3-phy";
+ };
+ };
+
+ mshc_0: mshc@15540000 {
+ compatible = "samsung,exynos7-dw-mshc-smu";
+ interrupts = <GIC_SPI 225 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x15540000 0x2000>;
+ clocks = <&cmu_fsys CLK_ACLK_MMC0>,
+ <&cmu_fsys CLK_SCLK_MMC0>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
+ };
+
+ mshc_1: mshc@15550000 {
+ compatible = "samsung,exynos7-dw-mshc-smu";
+ interrupts = <GIC_SPI 226 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x15550000 0x2000>;
+ clocks = <&cmu_fsys CLK_ACLK_MMC1>,
+ <&cmu_fsys CLK_SCLK_MMC1>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
+ };
+
+ mshc_2: mshc@15560000 {
+ compatible = "samsung,exynos7-dw-mshc-smu";
+ interrupts = <GIC_SPI 227 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x15560000 0x2000>;
+ clocks = <&cmu_fsys CLK_ACLK_MMC2>,
+ <&cmu_fsys CLK_SCLK_MMC2>;
+ clock-names = "biu", "ciu";
+ fifo-depth = <0x40>;
+ status = "disabled";
+ };
+
+ amba {
+ compatible = "arm,amba-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ pdma0: pdma@15610000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x15610000 0x1000>;
+ interrupts = <GIC_SPI 228 0>;
+ clocks = <&cmu_fsys CLK_PDMA0>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ pdma1: pdma@15600000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x15600000 0x1000>;
+ interrupts = <GIC_SPI 246 0>;
+ clocks = <&cmu_fsys CLK_PDMA1>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+ };
+
+ audio-subsystem@11400000 {
+ compatible = "samsung,exynos5433-lpass";
+ reg = <0x11400000 0x100>, <0x11500000 0x08>;
+ samsung,pmu-syscon = <&pmu_system_controller>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ adma: adma@11420000 {
+ compatible = "arm,pl330", "arm,primecell";
+ reg = <0x11420000 0x1000>;
+ interrupts = <GIC_SPI 73 0>;
+ clocks = <&cmu_aud CLK_ACLK_DMAC>;
+ clock-names = "apb_pclk";
+ #dma-cells = <1>;
+ #dma-channels = <8>;
+ #dma-requests = <32>;
+ };
+
+ i2s0: i2s0@11440000 {
+ compatible = "samsung,exynos7-i2s";
+ reg = <0x11440000 0x100>;
+ dmas = <&adma 0 &adma 2>;
+ dma-names = "tx", "rx";
+ interrupts = <GIC_SPI 70 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&cmu_aud CLK_PCLK_AUD_I2S>,
+ <&cmu_aud CLK_SCLK_AUD_I2S>,
+ <&cmu_aud CLK_SCLK_I2S_BCLK>;
+ clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_bus>;
+ status = "disabled";
+ };
+
+ serial_3: serial@11460000 {
+ compatible = "samsung,exynos5433-uart";
+ reg = <0x11460000 0x100>;
+ interrupts = <GIC_SPI 67 0>;
+ clocks = <&cmu_aud CLK_PCLK_AUD_UART>,
+ <&cmu_aud CLK_SCLK_AUD_UART>;
+ clock-names = "uart", "clk_uart_baud0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart_aud_bus>;
+ status = "disabled";
+ };
+ };
+ };
+
+ timer: timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+};
+
+#include "exynos5433-pinctrl.dtsi"
+#include "exynos5433-tmu.dtsi"
--
1.9.1

Next message: Chanwoo Choi: "[PATCH v3 2/5] pinctrl: samsung: Add GPF support for Exynos5433"
Previous message: Chanwoo Choi: "[PATCH v3 1/5] pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank"
In reply to: Krzysztof Kozlowski: "Re: [PATCH v3 1/5] pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank"
Next in thread: Andi Shyti: "Re: [PATCH v3 3/5] arm64: dts: exynos: Add dts files for Samsung Exynos5433 64bit SoC"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]