Re: [PATCH v1] HID: udraw: Add support for the uDraw tablet for PS3

From: Benjamin Tissoires
Date: Fri Nov 04 2016 - 11:04:15 EST

Next message: Krzysztof Kozlowski: "Re: [PATCH 10/13] ARM: dts: exynos: replace to "max-frequecy" instead of "clock-freq-min-max""
Previous message: Linus Walleij: "Re: [PATCH 4/9] pinctrl: meson: allow gpio to request irq"
In reply to: Bastien Nocera: "Re: [PATCH v1] HID: udraw: Add support for the uDraw tablet for PS3"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Nov 04 2016 or thereabouts, Bastien Nocera wrote:
> On Fri, 2016-11-04 at 15:26 +0100, Benjamin Tissoires wrote:
> > On Oct 27 2016 or thereabouts, Bastien Nocera wrote:
> > > This adds support for the THQ uDraw tablet for the PS3, as
> > > 4 separate device nodes, so that user-space can easily consume
> > > events coming from the hardware.
> > >
> > > Note that the touchpad two-finger support is fairly unreliable,
> > > and a right-click can only be achieved with a two-finger tap
> > > with the two fingers slightly apart (about 1cm should be enough).
> > >
> > > Tested-by: Bastien Nocera <hadess@xxxxxxxxxx>
> > > Signed-off-by: Bastien Nocera <hadess@xxxxxxxxxx>
> > > ---
> > > ÂMAINTAINERSÂÂÂÂÂÂÂÂÂÂÂÂÂ|ÂÂÂ6 +
> > > Âdrivers/hid/KconfigÂÂÂÂÂ|ÂÂÂ7 +
> > > Âdrivers/hid/MakefileÂÂÂÂ|ÂÂÂ1 +
> > > Âdrivers/hid/hid-core.cÂÂ|ÂÂÂ1 +
> > > Âdrivers/hid/hid-ids.hÂÂÂ|ÂÂÂ3 +
> > > Âdrivers/hid/hid-udraw.c | 478
> > > ++++++++++++++++++++++++++++++++++++++++++++++++
> > > Â6 files changed, 496 insertions(+)
> > > Âcreate mode 100644 drivers/hid/hid-udraw.c
> > >
> > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > index 33d7779..57f6bea 100644
> > > --- a/MAINTAINERS
> > > +++ b/MAINTAINERS
> > > @@ -12197,6 +12197,12 @@ S: Maintained
> > > ÂF: Documentation/filesystems/udf.txt
> > > ÂF: fs/udf/
> > > Â
> > > +UDRAW TABLET
> > > +M: Bastien Nocera <hadess@xxxxxxxxxx>
> > > +L: linux-input@xxxxxxxxxxxxxxx
> > > +S: Maintained
> > > +F: drivers/hid/hid-udraw.c
> > > +
> > > ÂUFS FILESYSTEM
> > > ÂM: Evgeniy Dushistov <dushistov@xxxxxxx>
> > > ÂS: Maintained
> > > diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
> > > index cd4599c..88c831e 100644
> > > --- a/drivers/hid/Kconfig
> > > +++ b/drivers/hid/Kconfig
> > > @@ -861,6 +861,13 @@ config THRUSTMASTER_FF
> > > Â ÂÂa THRUSTMASTER Dual Trigger 3-in-1 or a THRUSTMASTER
> > > Ferrari
> > > GT
> > > Â ÂÂRumble Force or Force Feedback Wheel.
> > > Â
> > > +config HID_UDRAW
> > > + tristate "THQ PS3 uDraw tablet"
> > > + depends on HID
> > > + ---help---
> > > + ÂÂSay Y here if you want to use the THQ uDraw gaming
> > > tablet
> > > for
> >
> > Looks like your MUA corrupted the patch...
>
> Yeah, I'll resend another way.
>
> > > + ÂÂthe PS3.
> > > +
> > > Âconfig HID_WACOM
> > > Â tristate "Wacom Intuos/Graphire tablet support (USB)"
> > > Â depends on HID
> > > diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
> > > index 86b2b57..d0d9b34 100644
> > > --- a/drivers/hid/Makefile
> > > +++ b/drivers/hid/Makefile
> > > @@ -96,6 +96,7 @@ obj-$(CONFIG_HID_TIVO) += hid-
> > > tivo.o
> > > Âobj-$(CONFIG_HID_TOPSEED) += hid-topseed.o
> > > Âobj-$(CONFIG_HID_TWINHAN) += hid-twinhan.o
> > > Âobj-$(CONFIG_HID_UCLOGIC) += hid-uclogic.o
> > > +obj-$(CONFIG_HID_UDRAW) += hid-udraw.o
> > > Âobj-$(CONFIG_HID_LED) += hid-led.o
> > > Âobj-$(CONFIG_HID_XINMO) += hid-xinmo.o
> > > Âobj-$(CONFIG_HID_ZEROPLUS) += hid-zpff.o
> > > diff --git a/drivers/hid/hid-core.c b/drivers/hid/hid-core.c
> > > index 2b89c70..3611ec7 100644
> > > --- a/drivers/hid/hid-core.c
> > > +++ b/drivers/hid/hid-core.c
> > > @@ -2086,6 +2086,7 @@ static const struct hid_device_id
> > > hid_have_special_driver[] = {
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_UCLOGIC_TABLET_WP1062) },
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_UCLOGIC_WIRELESS_TABLET_TWHL850) },
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_UCLOGIC_TABLET_TWHA60) },
> > > + { HID_USB_DEVICE(USB_VENDOR_ID_THQ,
> > > USB_DEVICE_ID_THQ_PS3_UDRAW) },
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_YIYNOVA_TABLET) },
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_UGEE_TABLET_81) },
> > > Â { HID_USB_DEVICE(USB_VENDOR_ID_UCLOGIC,
> > > USB_DEVICE_ID_UGEE_TABLET_45) },
> > > diff --git a/drivers/hid/hid-ids.h b/drivers/hid/hid-ids.h
> > > index cd59c79..4ff9ecc 100644
> > > --- a/drivers/hid/hid-ids.h
> > > +++ b/drivers/hid/hid-ids.h
> > > @@ -955,6 +955,9 @@
> > > Â#define USB_VENDOR_ID_THINGM 0x27b8
> > > Â#define USB_DEVICE_ID_BLINK1 0x01ed
> > > Â
> > > +#define USB_VENDOR_ID_THQ 0x20d6
> > > +#define USB_DEVICE_ID_THQ_PS3_UDRAW 0xcb17
> > > +
> > > Â#define USB_VENDOR_ID_THRUSTMASTER 0x044f
> > > Â
> > > Â#define USB_VENDOR_ID_TIVO 0x150a
> > > diff --git a/drivers/hid/hid-udraw.c b/drivers/hid/hid-udraw.c
> > > new file mode 100644
> > > index 0000000..794aae5
> > > --- /dev/null
> > > +++ b/drivers/hid/hid-udraw.c
> > > @@ -0,0 +1,478 @@
> > > +/*
> > > + * HID driver for THQ PS3 uDraw tablet
> > > + *
> > > + * Copyright (C) 2016 Red Hat Inc. All Rights Reserved
> > > + *
> > > + * This software is licensed under the terms of the GNU General
> > > Public
> > > + * License version 2, as published by the Free Software
> > > Foundation,
> > > and
> > > + * may be copied, distributed, and modified under those terms.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.ÂÂSee the
> > > + * GNU General Public License for more details.
> > > + */
> > > +
> > > +#include <linux/device.h>
> > > +#include <linux/hid.h>
> > > +#include <linux/module.h>
> > > +#include "hid-ids.h"
> > > +
> > > +MODULE_AUTHOR("Bastien Nocera <hadess@xxxxxxxxxx>");
> > > +MODULE_DESCRIPTION("PS3 uDraw tablet driver");
> > > +MODULE_LICENSE("GPL");
> > > +
> > > +/*
> > > + * Protocol information from:
> > > + * http://brandonw.net/udraw/
> > > + * and the source code of:
> > > + * https://vvvv.org/contribution/udraw-hid
> > > + */
> > > +
> > > +/*
> > > + * The device is setup with multiple input devices to make it
> > > easier
> > > + * to handle in user-space:
> >
> > That's also the correct way of doing it, given that this device is a
> > set
> > of distinct devices.
>
> So should I remove or expand the comment?

Probably just remove the "to make it easier to handle in user-space"
part.

>
> > > + * - the touch area which works as a touchpad
> > > + * - the tablet area which works as a touchpad/drawing tablet
> > > + * - a joypad with a d-pad, and 7 buttons
> > > + * - an accelerometer device
> > > + */
> > > +
> > > +enum {
> > > + TOUCH_NONE,
> > > + TOUCH_PEN,
> > > + TOUCH_FINGER,
> > > + TOUCH_TWOFINGER
> > > +};
> > > +
> > > +enum {
> > > + AXIS_X,
> > > + AXIS_Y,
> > > + AXIS_Z
> > > +};
> > > +
> > > +/* Accelerometer min/max values
> > > + * in order, X, Y and Z
> > > + */
> > > +struct {
> > > + int min;
> > > + int max;
> > > +} accel_limits[] = {
> > > + [AXIS_X] = { 0x1EA, 0x216 },
> > > + [AXIS_Y] = { 0x1EA, 0x216 },
> > > + [AXIS_Z] = { 0x1EC, 0x218 }
> >
> > Nitpicking, it feels weird writing min/max as hex values.
>
> For this and most of the hex values below, I'm using hex values because
> the various drivers I based this off used hex values. I can certainly
> convert them all, but this would lose the direct searchability for
> them. Just let me know which way I should go there.

Not sure the searchability is a valid argument. I'd say just convert the
hex values that makes sense (so here and the other places I noted).

>
> > > +};
> > > +
> > > +#define DEVICE_NAME "THQ uDraw Game Tablet for PS3"
> > > +/* resolution in pixels */
> > > +#define RES_X 1920
> > > +#define RES_Y 1080
> > > +/* size in mm */
> > > +#define WIDTHÂÂ160
> > > +#define HEIGHT 90
> > > +#define PRESSURE_OFFSET 0x71
> > > +#define MAX_PRESSURE (0xFF - PRESSURE_OFFSET)
> >
> > Why is pressure an hex value too?
> >
> > > +
> > > +struct udraw {
> > > + struct input_dev *joy_input_dev;
> > > + struct input_dev *touch_input_dev;
> > > + struct input_dev *pen_input_dev;
> > > + struct input_dev *accel_input_dev;
> > > + struct hid_device *hdev;
> > > +
> > > + /* The device's two-finger support is pretty unreliable,
> > > as
> >
> > Nitpicking, the kernel comment style requires to have the following:
> > /*
> > Â* foo
> > Â* bar
> > Â*/
>
> I'll fix that.
>
> > > + Â* the device could report a single touch when the two
> > > fingers
> > > + Â* are too close together, and the distance between
> > > fingers,
> > > even
> > > + Â* though reported is not in pixels, but in an arbitrary
> > > unit.
> >
> > There is no point in mentioning pixels here. All touchpads report
> > their
> > values in arbitrary units, which is then converted into unit per mm
> > by
> > using the resolution.
>
> OK.
>
> > > + Â*
> > > + Â* We'll make do without it, and try to report the first
> > > touch
> > > + Â* as reliably as possible.
> > > + Â*/
> > > + int last_one_finger_x;
> > > + int last_one_finger_y;
> > > + int last_two_finger_x;
> > > + int last_two_finger_y;
> > > +};
> > > +
> > > +static int clamp_accel(int axis, int offset)
> > > +{
> > > + axis = clamp(axis,
> > > + accel_limits[offset].min,
> > > + accel_limits[offset].max);
> > > + axis = (axis - accel_limits[offset].min) /
> > > + ((accel_limits[offset].max -
> > > + ÂÂaccel_limits[offset].min) * 0xFF);
> > > + return axis;
> > > +}
> > > +
> > > +static int udraw_raw_event(struct hid_device *hdev, struct
> > > hid_report
> > > *report,
> > > + Âu8 *data, int len)
> > > +{
> > > + struct udraw *udraw = hid_get_drvdata(hdev);
> > > + int touch;
> > > + int x, y, z;
> > > +
> > > + if (len != 0x1B)
> >
> > a length should not been expressed in hex.
> >
> > > + return 0;
> > > +
> > > + if (data[11] == 0x00)
> > > + touch = TOUCH_NONE;
> > > + else if (data[11] == 0x40)
> > > + touch = TOUCH_PEN;
> > > + else if (data[11] == 0x80)
> > > + touch = TOUCH_FINGER;
> > > + else
> > > + touch = TOUCH_TWOFINGER;
> > > +
> > > + /* joypad */
> > > + input_report_key(udraw->joy_input_dev, BTN_WEST, data[0] &
> > > 1);
> > > + input_report_key(udraw->joy_input_dev, BTN_SOUTH, data[0]
> > > &
> > > 2);
> >
> > you should report !!(data[0] & 2), or you'll send key repeat events
> > to
> > user space.
>
> Noted.
>
> > > + input_report_key(udraw->joy_input_dev, BTN_EAST, data[0] &
> > > 4);
> > > + input_report_key(udraw->joy_input_dev, BTN_NORTH, data[0]
> > > &
> > > 8);
> >
> > Same for those 2, keys should be reported with a value of 0 or 1.
> >
> > > +
> > > + input_report_key(udraw->joy_input_dev, BTN_SELECT, data[1]
> > > &
> > > 1);
> > > + input_report_key(udraw->joy_input_dev, BTN_START, data[1]
> > > &
> > > 2);
> > > + input_report_key(udraw->joy_input_dev, BTN_MODE, data[1] &
> > > 16);
> >
> > rinse, wash, repeat
> >
> > > +
> > > + x = y = 0;
> > > + switch (data[2]) {
> > > + case 0x0:
> > > + y = -127;
> > > + break;
> > > + case 0x1:
> > > + y = -127;
> > > + x = 127;
> > > + break;
> > > + case 0x2:
> > > + x = 127;
> > > + break;
> > > + case 0x3:
> > > + y = 127;
> > > + x = 127;
> > > + break;
> > > + case 0x4:
> > > + y = 127;
> > > + break;
> > > + case 0x5:
> > > + y = 127;
> > > + x = -127;
> > > + break;
> > > + case 0x6:
> > > + x = -127;
> > > + break;
> > > + case 0x7:
> > > + y = -127;
> > > + x = -127;
> > > + break;
> > > + default:
> > > + break;
> > > + }
> > > +
> > > + input_report_abs(udraw->joy_input_dev, ABS_X, x);
> > > + input_report_abs(udraw->joy_input_dev, ABS_Y, y);
> > > +
> > > + input_sync(udraw->joy_input_dev);
> > > +
> > > + /* For pen and touchpad */
> > > + x = y = 0;
> > > + if (touch != TOUCH_NONE) {
> > > + if (data[15] != 0x0F)
> > > + x = data[15] * 256 + data[17];
> > > + if (data[16] != 0x0F)
> > > + y = data[16] * 256 + data[18];
> > > + }
> > > +
> > > + if (touch == TOUCH_FINGER) {
> > > + /* Save the last one-finger touch */
> > > + udraw->last_one_finger_x = x;
> > > + udraw->last_one_finger_y = y;
> > > + udraw->last_two_finger_x = -1;
> > > + udraw->last_two_finger_y = -1;
> > > + } else if (touch == TOUCH_TWOFINGER) {
> > > + /* We have a problem because x/y is the one for
> > > the
> >
> > comment style please (though IIRC, Jiri doesn't care much).
> >
> > > + Â* second finger but we want the first finger
> > > given
> > > + Â* to user-space otherwise it'll look as if it
> > > jumped.
> > > + Â*/
> > > + if (udraw->last_two_finger_x == -1) {
> > > + /* Save the position of the 2nd finger */
> > > + udraw->last_two_finger_x = x;
> > > + udraw->last_two_finger_y = y;
> > > +
> > > + x = udraw->last_one_finger_x;
> > > + y = udraw->last_one_finger_y;
> > > + } else {
> > > + /* Offset the 2-finger coords using the
> > > + Â* saved data from the first finger
> > > + Â*/
> > > + x = x - (udraw->last_two_finger_x
> > > + - udraw->last_one_finger_x);
> > > + y = y - (udraw->last_two_finger_y
> > > + - udraw->last_one_finger_y);
> > > + }
> >
> > This way of reporting the fingers is terrible. However, Bastien asked
> > for some early reviews and this was the most acceptable solution.
>
> Should I add a longer comment there?

No, that's fine. I was just adding this to explain to other that this is
the less worse solution.

Actually, a comment would be interesting to have to prevent people to be
smarter and spend too much time there...

Cheers,
Benjamin

>
> > > + }
> > > +
> > > + /* touchpad */
> > > + if (touch == TOUCH_FINGER || touch == TOUCH_TWOFINGER) {
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOUCH,
> > > 1);
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOOL_FINGER,
> > > + touch == TOUCH_FINGER);
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOOL_DOUBLETAP,
> > > + touch == TOUCH_TWOFINGER);
> > > +
> > > + input_report_abs(udraw->touch_input_dev, ABS_X,
> > > x);
> > > + input_report_abs(udraw->touch_input_dev, ABS_Y,
> > > y);
> > > + } else {
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOUCH,
> > > 0);
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOOL_FINGER, 0);
> > > + input_report_key(udraw->touch_input_dev,
> > > BTN_TOOL_DOUBLETAP, 0);
> > > + }
> > > + input_sync(udraw->touch_input_dev);
> > > +
> > > + /* pen */
> > > + if (touch == TOUCH_PEN) {
> > > + int level;
> > > +
> > > + level = clamp(data[13] - PRESSURE_OFFSET,
> > > + 0, MAX_PRESSURE);
> > > +
> > > + input_report_key(udraw->pen_input_dev, BTN_TOUCH,
> > > (level != 0));
> > > + input_report_key(udraw->pen_input_dev,
> > > BTN_TOOL_PEN,
> > > 1);
> > > + input_report_abs(udraw->pen_input_dev,
> > > ABS_PRESSURE,
> > > level);
> > > + input_report_abs(udraw->pen_input_dev, ABS_X, x);
> > > + input_report_abs(udraw->pen_input_dev, ABS_Y, y);
> > > + } else {
> > > + input_report_key(udraw->pen_input_dev, BTN_TOUCH,
> > > 0);
> > > + input_report_key(udraw->pen_input_dev,
> > > BTN_TOOL_PEN,
> > > 0);
> > > + input_report_abs(udraw->pen_input_dev,
> > > ABS_PRESSURE,
> > > 0);
> > > + }
> > > + input_sync(udraw->pen_input_dev);
> > > +
> > > + /* accel */
> > > + x = (data[19] + (data[20] << 8));
> > > + x = clamp_accel(x, AXIS_X);
> > > + y = (data[21] + (data[22] << 8));
> > > + y = clamp_accel(y, AXIS_Y);
> > > + z = (data[23] + (data[24] << 8));
> > > + z = clamp_accel(z, AXIS_Z);
> > > + input_report_abs(udraw->accel_input_dev, ABS_X, x);
> > > + input_report_abs(udraw->accel_input_dev, ABS_Y, y);
> > > + input_report_abs(udraw->accel_input_dev, ABS_Z, z);
> > > + input_sync(udraw->accel_input_dev);
> > > +
> > > + /* let hidraw and hiddev handle the report */
> > > + return 0;
> > > +}
> > > +
> > > +static int udraw_open(struct input_dev *dev)
> > > +{
> > > + struct udraw *udraw = input_get_drvdata(dev);
> > > +
> > > + return hid_hw_open(udraw->hdev);
> > > +}
> > > +
> > > +static void udraw_close(struct input_dev *dev)
> > > +{
> > > + struct udraw *udraw = input_get_drvdata(dev);
> > > +
> > > + hid_hw_close(udraw->hdev);
> > > +}
> > > +
> > > +static struct input_dev *allocate_and_setup(struct hid_device
> > > *hdev,
> > > + const char *name)
> > > +{
> > > + struct input_dev *input_dev;
> > > +
> > > + input_dev = devm_input_allocate_device(&hdev->dev);
> > > + if (!input_dev)
> > > + return NULL;
> > > +
> > > + input_dev->name = name;
> > > + input_dev->phys = hdev->phys;
> > > + input_dev->dev.parent = &hdev->dev;
> > > + input_dev->open = udraw_open;
> > > + input_dev->close = udraw_close;
> > > + input_dev->uniq = hdev->uniq;
> > > + input_dev->id.bustype = hdev->bus;
> > > + input_dev->id.vendorÂÂ= hdev->vendor;
> > > + input_dev->id.product = hdev->product;
> > > + input_dev->id.version = hdev->version;
> > > + input_set_drvdata(input_dev, hid_get_drvdata(hdev));
> > > +
> > > + return input_dev;
> > > +}
> > > +
> > > +static bool udraw_setup_touch(struct udraw *udraw,
> > > + struct hid_device *hdev)
> > > +{
> > > + struct input_dev *input_dev;
> > > +
> > > + input_dev = allocate_and_setup(hdev, DEVICE_NAME "
> > > Touchpad");
> > > + if (!input_dev)
> > > + return false;
> > > +
> > > + input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
> > > +
> > > + set_bit(ABS_X, input_dev->absbit);
> >
> > No need to set this, it will be set by input_set_abs_params()
>
> Noted.
>
> > > + input_set_abs_params(input_dev, ABS_X, 0, RES_X, 1, 0);
> > > + input_abs_set_res(input_dev, ABS_X, RES_X / WIDTH);
> > > + set_bit(ABS_Y, input_dev->absbit);
> >
> > likewise
> >
> > > + input_set_abs_params(input_dev, ABS_Y, 0, RES_Y, 1, 0);
> > > + input_abs_set_res(input_dev, ABS_Y, RES_Y / HEIGHT);
> > > +
> > > + set_bit(BTN_TOUCH, input_dev->keybit);
> > > + set_bit(BTN_TOOL_FINGER, input_dev->keybit);
> > > + set_bit(BTN_TOOL_DOUBLETAP, input_dev->keybit);
> > > +
> > > + set_bit(INPUT_PROP_POINTER, input_dev->propbit);
> > > +
> > > + udraw->touch_input_dev = input_dev;
> > > +
> > > + return true;
> > > +}
> > > +
> > > +static bool udraw_setup_pen(struct udraw *udraw,
> > > + struct hid_device *hdev)
> > > +{
> > > + struct input_dev *input_dev;
> > > +
> > > + input_dev = allocate_and_setup(hdev, DEVICE_NAME " Pen");
> > > + if (!input_dev)
> > > + return false;
> > > +
> > > + input_dev->evbit[0] = BIT(EV_ABS) | BIT(EV_KEY);
> > > +
> > > + set_bit(ABS_X, input_dev->absbit);
> >
> > no need to set this
> >
> > > + input_set_abs_params(input_dev, ABS_X, 0, RES_X, 1, 0);
> > > + input_abs_set_res(input_dev, ABS_X, RES_X / WIDTH);
> > > + set_bit(ABS_Y, input_dev->absbit);
> >
> > idem
> >
> > > + input_set_abs_params(input_dev, ABS_Y, 0, RES_Y, 1, 0);
> > > + input_abs_set_res(input_dev, ABS_Y, RES_Y / HEIGHT);
> > > + set_bit(ABS_PRESSURE, input_dev->absbit);
> >
> > idem
> >
> > > + input_set_abs_params(input_dev, ABS_PRESSURE,
> > > + 0, MAX_PRESSURE, 0, 0);
> > > +
> > > + set_bit(BTN_TOUCH, input_dev->keybit);
> > > + set_bit(BTN_TOOL_PEN, input_dev->keybit);
> > > +
> > > + set_bit(INPUT_PROP_POINTER, input_dev->propbit);
> > > +
> > > + udraw->pen_input_dev = input_dev;
> > > +
> > > + return true;
> > > +}
> > > +
> > > +static bool udraw_setup_accel(struct udraw *udraw,
> > > + struct hid_device *hdev)
> > > +{
> > > + struct input_dev *input_dev;
> > > +
> > > + input_dev = allocate_and_setup(hdev, DEVICE_NAME "
> > > Accelerometer");
> > > + if (!input_dev)
> > > + return false;
> > > +
> > > + input_dev->evbit[0] = BIT(EV_ABS);
> > > +
> > > + /* 1G accel is reported as ~256, so clamp to 2G */
> > > + set_bit(ABS_X, input_dev->absbit);
> >
> > no need to set this
> >
> > > + input_set_abs_params(input_dev, ABS_X, -512, 512, 0, 0);
> > > + set_bit(ABS_Y, input_dev->absbit);
> >
> > idem
> >
> > > + input_set_abs_params(input_dev, ABS_Y, -512, 512, 0, 0);
> > > + set_bit(ABS_Z, input_dev->absbit);
> >
> > idem
> >
> > > + input_set_abs_params(input_dev, ABS_Z, -512, 512, 0, 0);
> > > +
> > > + set_bit(INPUT_PROP_ACCELEROMETER, input_dev->propbit);
> > > +
> > > + udraw->accel_input_dev = input_dev;
> > > +
> > > + return true;
> > > +}
> > > +
> > > +static bool udraw_setup_joypad(struct udraw *udraw,
> > > + struct hid_device *hdev)
> > > +{
> > > + struct input_dev *input_dev;
> > > +
> > > + input_dev = allocate_and_setup(hdev, DEVICE_NAME "
> > > Joypad");
> > > + if (!input_dev)
> > > + return false;
> > > +
> > > + input_dev->evbit[0] = BIT(EV_KEY) | BIT(EV_ABS);
> > > +
> > > + set_bit(BTN_SOUTH, input_dev->keybit);
> > > + set_bit(BTN_NORTH, input_dev->keybit);
> > > + set_bit(BTN_EAST, input_dev->keybit);
> > > + set_bit(BTN_WEST, input_dev->keybit);
> > > + set_bit(BTN_SELECT, input_dev->keybit);
> > > + set_bit(BTN_START, input_dev->keybit);
> > > + set_bit(BTN_MODE, input_dev->keybit);
> > > +
> > > + set_bit(ABS_X, input_dev->absbit);
> >
> > no need to set this
> >
> > > + input_set_abs_params(input_dev, ABS_X, -127, 127, 0, 0);
> > > + set_bit(ABS_Y, input_dev->absbit);
> >
> > idem
> >
> > > + input_set_abs_params(input_dev, ABS_Y, -127, 127, 0, 0);
> > > +
> > > + udraw->joy_input_dev = input_dev;
> > > +
> > > + return true;
> > > +}
> > > +
> > > +static int udraw_probe(struct hid_device *hdev, const struct
> > > hid_device_id *id)
> > > +{
> > > + struct udraw *udraw;
> > > + int ret;
> > > +
> > > + udraw = devm_kzalloc(&hdev->dev, sizeof(struct udraw),
> > > GFP_KERNEL);
> > > + if (!udraw)
> > > + return -ENOMEM;
> > > +
> > > + udraw->hdev = hdev;
> > > + udraw->last_two_finger_x = -1;
> > > + udraw->last_two_finger_y = -1;
> > > +
> > > + hid_set_drvdata(hdev, udraw);
> > > +
> > > + ret = hid_parse(hdev);
> > > + if (ret) {
> > > + hid_err(hdev, "parse failed\n");
> > > + return ret;
> > > + }
> > > +
> > > + if (!udraw_setup_joypad(udraw, hdev) ||
> > > + ÂÂÂÂ!udraw_setup_touch(udraw, hdev) ||
> > > + ÂÂÂÂ!udraw_setup_pen(udraw, hdev) ||
> > > + ÂÂÂÂ!udraw_setup_accel(udraw, hdev)) {
> > > + hid_err(hdev, "could not allocate interfaces\n");
> > > + return -ENOMEM;
> > > + }
> > > +
> > > + ret = input_register_device(udraw->joy_input_dev) ||
> > > + input_register_device(udraw->touch_input_dev) ||
> > > + input_register_device(udraw->pen_input_dev) ||
> > > + input_register_device(udraw->accel_input_dev);
> > > + if (ret) {
> > > + hid_err(hdev, "failed to register interfaces\n");
> > > + return ret;
> > > + }
> > > +
> > > + ret = hid_hw_start(hdev, HID_CONNECT_HIDRAW |
> > > HID_CONNECT_DRIVER);
> > > + if (ret) {
> > > + hid_err(hdev, "hw start failed\n");
> > > + return ret;
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static const struct hid_device_id udraw_devices[] = {
> > > + { HID_USB_DEVICE(USB_VENDOR_ID_THQ,
> > > USB_DEVICE_ID_THQ_PS3_UDRAW) },
> > > + { }
> > > +};
> > > +MODULE_DEVICE_TABLE(hid, udraw_devices);
> > > +
> > > +static struct hid_driver udraw_driver = {
> > > + .name = "hid-udraw",
> > > + .id_table = udraw_devices,
> > > + .raw_event = udraw_raw_event,
> > > + .probe = udraw_probe,
> > > +};
> > > +module_hid_driver(udraw_driver);
> > > --Â
> > > 2.7.4
> >
> > Cheers,
> > Benjamin
> >

Next message: Krzysztof Kozlowski: "Re: [PATCH 10/13] ARM: dts: exynos: replace to "max-frequecy" instead of "clock-freq-min-max""
Previous message: Linus Walleij: "Re: [PATCH 4/9] pinctrl: meson: allow gpio to request irq"
In reply to: Bastien Nocera: "Re: [PATCH v1] HID: udraw: Add support for the uDraw tablet for PS3"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]