[PATCH 4.8 073/138] ARM: dts: fix the SD card on the Snowball

From: Greg Kroah-Hartman
Date: Wed Nov 09 2016 - 06:08:28 EST


4.8-stable review patch. If anyone has any objections, please let me know.

------------------

From: Linus Walleij <linus.walleij@xxxxxxxxxx>

commit 1b283eea6228880b765bc40fe4e555416437ce58 upstream.

This fixes a very annoying regression on the Snowball SD card
that has been around for a while. It turns out that the device
tree does not configure the direction pins properly, nor sets
up the pins for the voltage converter properly at boot. Unless
all things are correctly set up, the feedback clock will not
work, and makes the driver spew messages in the console (but
it works, very slowly):

root@Ux500:/ mount /dev/mmcblk0p2 /mnt/
[ 9.953460] mmci-pl18x 80126000.sdi0_per1: error during DMA transfer!
[ 9.960296] mmcblk0: error -110 sending status command, retrying
[ 9.966461] mmcblk0: error -110 sending status command, retrying
[ 9.972534] mmcblk0: error -110 sending status command, aborting

Fix this by rectifying the device tree to correspond to that of
the Ux500 HREF boards plus the DAT31DIR setting that is unique for
the Snowball, and things start working smoothly. Add in the SDR12
and SDR25 modes which this host can do without any problems.

I don't know if this has ever been correct, sadly. It works after
this patch.

Reported-by: Daniel Lezcano <daniel.lezcano@xxxxxxxxxx>
Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx>
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: Olof Johansson <olof@xxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>

---
arch/arm/boot/dts/ste-snowball.dts | 15 +++++++++++++--
1 file changed, 13 insertions(+), 2 deletions(-)

--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -239,14 +239,25 @@
arm,primecell-periphid = <0x10480180>;
max-frequency = <100000000>;
bus-width = <4>;
+ cap-sd-highspeed;
cap-mmc-highspeed;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ /* All direction control is used */
+ st,sig-dir-cmd;
+ st,sig-dir-dat0;
+ st,sig-dir-dat2;
+ st,sig-dir-dat31;
+ st,sig-pin-fbclk;
+ full-pwr-cycle;
vmmc-supply = <&ab8500_ldo_aux3_reg>;
vqmmc-supply = <&vmmci>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdi0_default_mode>;
pinctrl-1 = <&sdi0_sleep_mode>;

- cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>; // 218
+ /* GPIO218 MMC_CD */
+ cd-gpios = <&gpio6 26 GPIO_ACTIVE_LOW>;

status = "okay";
};
@@ -549,7 +560,7 @@
/* VMMCI level-shifter enable */
snowball_cfg3 {
pins = "GPIO217_AH12";
- ste,config = <&gpio_out_lo>;
+ ste,config = <&gpio_out_hi>;
};
/* VMMCI level-shifter voltage select */
snowball_cfg4 {