Re: [PATCH 3/3] ARM: dts: sunxi: add support for Orange Pi Zero board

[Chen-Yu Tsai]

On Mon, Nov 14, 2016 at 4:58 PM, Maxime Ripard
<maxime.ripard@xxxxxxxxxxxxxxxxxx> wrote:
> Hi,
>
> On Sat, Nov 12, 2016 at 12:46:54AM +0800, Icenowy Zheng wrote:
>> Orange Pi Zero is a board that came with the new Allwinner H2+ SoC.
>>
>> Add a device tree file for it.
>>
>> As there's still no mainline-compatible driver for the SDIO WLAN card on
>> board (a new card by Allwinner), the mmc1 controller is not enabled yet.
>>
>> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
>> ---
>>  arch/arm/boot/dts/Makefile                       |   1 +
>>  arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts | 148 +++++++++++++++++++++++
>>  2 files changed, 149 insertions(+)
>>  create mode 100644 arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index befcd26..9843fb0 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -818,6 +818,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
>>       sun8i-a33-sinlinx-sina33.dtb \
>>       sun8i-a83t-allwinner-h8homlet-v2.dtb \
>>       sun8i-a83t-cubietruck-plus.dtb \
>> +     sun8i-h2plus-orangepi-zero.dtb \
>>       sun8i-h3-bananapi-m2-plus.dtb \
>>       sun8i-h3-nanopi-neo.dtb \
>>       sun8i-h3-orangepi-2.dtb \
>> diff --git a/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
>> new file mode 100644
>> index 0000000..581f56e
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/sun8i-h2plus-orangepi-zero.dts
>> @@ -0,0 +1,148 @@
>> +/*
>> + * Copyright (C) 2016 Icenowy Zheng <icenowy@xxxxxxxx>
>> + *
>> + * Based on sun8i-h3-orangepi-one.dts, which is:
>> + *   Copyright (C) 2016 Hans de Goede <hdegoede@xxxxxxxxxx>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + *  a) This file is free software; you can redistribute it and/or
>> + *     modify it under the terms of the GNU General Public License as
>> + *     published by the Free Software Foundation; either version 2 of the
>> + *     License, or (at your option) any later version.
>> + *
>> + *     This file is distributed in the hope that it will be useful,
>> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>> + *     GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + *  b) Permission is hereby granted, free of charge, to any person
>> + *     obtaining a copy of this software and associated documentation
>> + *     files (the "Software"), to deal in the Software without
>> + *     restriction, including without limitation the rights to use,
>> + *     copy, modify, merge, publish, distribute, sublicense, and/or
>> + *     sell copies of the Software, and to permit persons to whom the
>> + *     Software is furnished to do so, subject to the following
>> + *     conditions:
>> + *
>> + *     The above copyright notice and this permission notice shall be
>> + *     included in all copies or substantial portions of the Software.
>> + *
>> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + *     OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +/dts-v1/;
>> +#include "sun8i-h2plus.dtsi"
>> +#include "sunxi-common-regulators.dtsi"
>> +
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> +     model = "Xunlong Orange Pi Zero";
>> +     compatible = "xunlong,orangepi-zero", "allwinner,sun8i-h2plus",
>> +                  "allwinner,sun8i-h3";
>
> You don't need the H3 compatible here.
>
>> +
>> +     aliases {
>> +             serial0 = &uart0;
>> +     };
>> +
>> +     chosen {
>> +             stdout-path = "serial0:115200n8";
>> +     };
>> +
>> +     leds {
>> +             compatible = "gpio-leds";
>> +             pinctrl-names = "default";
>> +             pinctrl-0 = <&leds_opi0>, <&leds_r_opi0>;
>> +
>> +             pwr_led {
>> +                     label = "orangepi:green:pwr";
>> +                     gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
>> +                     default-state = "on";
>> +             };
>> +
>> +             status_led {
>> +                     label = "orangepi:red:status";
>> +                     gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>;
>> +             };
>> +     };
>> +};
>> +
>> +&ehci1 {
>> +     status = "okay";
>> +};
>> +
>> +&mmc0 {
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
>> +     vmmc-supply = <&reg_vcc3v3>;
>> +     bus-width = <4>;
>> +     cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
>> +     cd-inverted;
>> +     status = "okay";
>> +};
>> +
>> +&ohci1 {
>> +     status = "okay";
>> +};
>> +
>> +&pio {
>> +     leds_opi0: led_pins@0 {
>> +             allwinner,pins = "PA17";
>> +             allwinner,function = "gpio_out";
>> +             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> +     };
>> +};
>> +
>> +&r_pio {
>> +     leds_r_opi0: led_pins@0 {
>> +             allwinner,pins = "PL10";
>> +             allwinner,function = "gpio_out";
>> +             allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> +             allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>
> You can drop the drive and pull properties, and could you use the
> generic pins and function properties for those nodes?

Icenowy,
Given that sunxi-next is currently broken for the pinctrl stuff,
you will need this patch to test, until Linus merges it:

    https://github.com/wens/linux/commit/e8ce92925a6dd1b2b38ed8699e81d0bc9804de20

>
>> +     };
>> +};
>> +
>> +&uart0 {
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&uart0_pins_a>;
>> +     status = "okay";
>> +};
>> +
>> +&uart1 {
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&uart1_pins>;
>> +     status = "disabled";
>> +};
>> +
>> +&uart2 {
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&uart2_pins>;
>> +     status = "disabled";
>> +};
>> +
>> +&uart3 {
>> +     pinctrl-names = "default";
>> +     pinctrl-0 = <&uart3_pins>;
>> +     status = "disabled";
>> +};
>
> I'm guessing that those UART are exposed on headers?
>
>> +
>> +&usbphy {
>> +     /* USB VBUS is always on */
>
> You can put the always on regulators (I'm guessing reg_vcc5v0 ?) here.

AFAIK the regulator properties are optional the the USB PHY.
So we probably don't need to add it. Hans (CC-ed) could explain
his original intent?

Regards
ChenYu

>
>> +     status = "okay";
>> +};
>
> Thanks,
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux and Kernel engineering
> http://free-electrons.com