Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board

From: Nicolas Ferre
Date: Mon Nov 14 2016 - 10:37:13 EST

Next message: Alex Williamson: "Re: [PATCH v11 11/22] vfio iommu: Add blocking notifier to notify DMA_UNMAP"
Previous message: Stefan Wahren: "Re: [PATCH 1/2] pinctrl: bcm2835: Fix ints for GPIOs 28-31 & 46-53"
Next in thread: Sudeep Holla: "Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Le 02/11/2016 à 04:05, Wenyou Yang a écrit :
> The sama5d36ek CMP board is the variant of sama5d3xek board.
> It is equipped with the low-power DDR2 SDRAM, PMIC ACT8865 and
> some power rail. Its main purpose is used to measure the power
> consumption.
> The difference of the sama5d36ek CMP dts from sama5d36ek dts
> is listed as below.
> 1. The USB host nodes are removed, that is, the USB host is disabled.
> 2. The gpio_keys node is added to wake up from the sleep.
> 3. The LCD isn't supported due to the pins for LCD are conflicted
> with gpio_keys.
> 4. The adc0 node support the pinctrl sleep state to fix the over
> consumption on VDDANA.
>
> As said in errata, "When the USB host ports are used in high speed
> mode (EHCI), it is not possible to suspend the ports if no device is
> attached on each port. This leads to increased power consumption even
> if the system is in a low power mode." That is why the the USB host
> is disabled.
>
> Signed-off-by: Wenyou Yang <wenyou.yang@xxxxxxxxx>
> ---
>
> Changes in v2:
> - Add the pinctrl sleep state for adc0 node to fix the over
> consumption on VDDANA.
> - Improve the commit log.
>
> arch/arm/boot/dts/sama5d36ek_cmp.dts | 51 +++++++
> arch/arm/boot/dts/sama5d3xcm_cmp.dtsi | 166 +++++++++++++++++++++
> arch/arm/boot/dts/sama5d3xmb_cmp.dtsi | 265 ++++++++++++++++++++++++++++++++++
> 3 files changed, 482 insertions(+)
> create mode 100644 arch/arm/boot/dts/sama5d36ek_cmp.dts
> create mode 100644 arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> create mode 100644 arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
>
> diff --git a/arch/arm/boot/dts/sama5d36ek_cmp.dts b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> new file mode 100644
> index 0000000..fd6bcd6
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d36ek_cmp.dts
> @@ -0,0 +1,51 @@
> +/*
> + * sama5d36ek_cmp.dts - Device Tree file for SAMA5D36-EK CMP board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.

No, in fact we now use a dual license scheme for DT files. Please have a
look at the recent board that we posted to take the header from them.

> + */
> +/dts-v1/;
> +#include "sama5d36.dtsi"
> +#include "sama5d3xmb_cmp.dtsi"
> +
> +/ {
> + model = "Atmel SAMA5D36-EK";
> + compatible = "atmel,sama5d36ek", "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d36", "atmel,sama5d3", "atmel,sama5";

I don't think the model name nor the compatible string reflect the
nature of this new "CMP" board.

> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + status = "okay";
> + };
> +
> + ssc0: ssc@f0008000 {
> + status = "okay";
> + };
> +
> + can0: can@f000c000 {
> + status = "okay";
> + };
> +
> + i2c0: i2c@f0014000 {
> + status = "okay";
> + };
> +
> + i2c1: i2c@f0018000 {
> + status = "okay";
> + };
> +
> + macb0: ethernet@f0028000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + status = "okay";
> + };
> + };
> + };
> +
> + sound {
> + status = "okay";
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> new file mode 100644
> index 0000000..77638c3
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xcm_cmp.dtsi
> @@ -0,0 +1,166 @@
> +/*
> + * sama5d3xcm_cmp.dtsi - Device Tree Include file for SAMA5D36 CMP CPU Module
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.

Ditto.

> + */
> +
> +/ {
> + compatible = "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";

Ditto.

> +
> + chosen {
> + bootargs = "rootfstype=ubifs ubi.mtd=5 root=ubi0:rootfs";

Remove bootargs.

> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x20000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + spi0: spi@f0004000 {
> + cs-gpios = <&pioD 13 0>, <0>, <0>, <0>;
> + };
> +
> + macb0: ethernet@f0028000 {
> + phy-mode = "rgmii";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethernet-phy@1 {
> + reg = <0x1>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> +
> + ethernet-phy@7 {
> + reg = <0x7>;
> + interrupt-parent = <&pioB>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> + txen-skew-ps = <800>;
> + txc-skew-ps = <3000>;
> + rxdv-skew-ps = <400>;
> + rxc-skew-ps = <3000>;
> + rxd0-skew-ps = <400>;
> + rxd1-skew-ps = <400>;
> + rxd2-skew-ps = <400>;
> + rxd3-skew-ps = <400>;
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + pmic: act8865@5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "disabled";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1100000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddana_reg: LDO_REG1 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG2 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> + };
> + };
> + };
> + };
> +
> + nand0: nand@60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + at91bootstrap@0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x40000>;
> + };
> +
> + bootloader@40000 {
> + label = "bootloader";
> + reg = <0x40000 0x80000>;
> + };
> +
> + bootloaderenv@c0000 {
> + label = "bootloader env";
> + reg = <0xc0000 0xc0000>;
> + };
> +
> + dtb@180000 {
> + label = "device tree";
> + reg = <0x180000 0x80000>;
> + };
> +
> + kernel@200000 {
> + label = "kernel";
> + reg = <0x200000 0x600000>;
> + };
> +
> + rootfs@800000 {
> + label = "rootfs";
> + reg = <0x800000 0x0f800000>;
> + };
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + d2 {
> + label = "d2";
> + gpios = <&pioE 25 GPIO_ACTIVE_LOW>; /* PE25, conflicts with A25, RXD2 */
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +};
> diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> new file mode 100644
> index 0000000..62c6230
> --- /dev/null
> +++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
> @@ -0,0 +1,265 @@
> +/*
> + * sama5d3xmb_cmp.dts - Device Tree file for SAMA5D3x CMP mother board
> + *
> + * Copyright (C) 2016 Atmel,
> + *
> + * Licensed under GPLv2 or later.

Ditto.

> + */
> +#include "sama5d3xcm_cmp.dtsi"
> +
> +/ {
> + compatible = "atmel,sama5d3xmb", "atmel,sama5d3xcm", "atmel,sama5d3", "atmel,sama5";

Ditto.

> +
> + ahb {
> + apb {
> + mmc0: mmc@f0000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 17 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + spi0: spi@f0004000 {
> + dmas = <0>, <0>; /* Do not use DMA for spi0 */
> +
> + m25p80@0 {
> + compatible = "atmel,at25df321a";
> + spi-max-frequency = <50000000>;
> + reg = <0>;
> + };
> + };
> +
> + ssc0: ssc@f0008000 {
> + atmel,clk-from-rk-pin;
> + };
> +
> + /*
> + * i2c0 conflicts with ISI:
> + * disable it to allow the use of ISI
> + * can not enable audio when i2c0 disabled
> + */
> + i2c0: i2c@f0014000 {
> + wm8904: wm8904@1a {
> + compatible = "wlf,wm8904";
> + reg = <0x1a>;
> + clocks = <&pck0>;
> + clock-names = "mclk";
> + };
> + };
> +
> + i2c1: i2c@f0018000 {
> + ov2640: camera@0x30 {
> + compatible = "ovti,ov2640";
> + reg = <0x30>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
> + resetb-gpios = <&pioE 24 GPIO_ACTIVE_LOW>;
> + pwdn-gpios = <&pioE 29 GPIO_ACTIVE_HIGH>;
> + /* use pck1 for the master clock of ov2640 */
> + clocks = <&pck1>;
> + clock-names = "xvclk";
> + assigned-clocks = <&pck1>;
> + assigned-clock-rates = <25000000>;
> +
> + port {
> + ov2640_0: endpoint {
> + remote-endpoint = <&isi_0>;
> + bus-width = <8>;
> + };
> + };
> + };
> + };
> +
> + usart1: serial@f0020000 {
> + dmas = <0>, <0>; /* Do not use DMA for usart1 */
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usart1 &pinctrl_usart1_rts_cts>;
> + status = "okay";
> + };
> +
> + isi: isi@f0034000 {
> + port {
> + isi_0: endpoint {
> + remote-endpoint = <&ov2640_0>;
> + bus-width = <8>;
> + vsync-active = <1>;
> + hsync-active = <1>;
> + };
> + };
> + };
> +
> + mmc1: mmc@f8000000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3 &pinctrl_mmc1_cd>;
> + status = "okay";
> + slot@0 {
> + reg = <0>;
> + bus-width = <4>;
> + cd-gpios = <&pioD 18 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + adc0: adc@f8018000 {
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <
> + &pinctrl_adc0_adtrg
> + &pinctrl_adc0_ad0
> + &pinctrl_adc0_ad1
> + &pinctrl_adc0_ad2
> + &pinctrl_adc0_ad3
> + &pinctrl_adc0_ad4
> + >;
> + pinctrl-1 = <
> + &pinctrl_adc0_adtrg_sleep
> + &pinctrl_adc0_ad0_sleep
> + &pinctrl_adc0_ad1_sleep
> + &pinctrl_adc0_ad2_sleep
> + &pinctrl_adc0_ad3_sleep
> + &pinctrl_adc0_ad4_sleep
> + >;
> + status = "okay";
> + };
> +
> + macb1: ethernet@f802c000 {
> + phy-mode = "rmii";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy0: ethernet-phy@1 {
> + /*interrupt-parent = <&pioE>;*/
> + /*interrupts = <30 IRQ_TYPE_EDGE_FALLING>;*/
> + reg = <1>;
> + };
> + };
> +
> + pinctrl@fffff200 {
> + adc0 {
> + pinctrl_adc0_adtrg_sleep: adc0_adtrg_1 {
> + atmel,pins =
> + <AT91_PIOD 19 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD19 GPIO output 0 */
> + };
> + pinctrl_adc0_ad0_sleep: adc0_ad0_1 {
> + atmel,pins =
> + <AT91_PIOD 20 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD20 GPIO output 0 */
> + };
> + pinctrl_adc0_ad1_sleep: adc0_ad1_1 {
> + atmel,pins =
> + <AT91_PIOD 21 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD21 GPIO output 0 */
> + };
> + pinctrl_adc0_ad2_sleep: adc0_ad2_1 {
> + atmel,pins =
> + <AT91_PIOD 22 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD22 GPIO output 0 */
> + };
> + pinctrl_adc0_ad3_sleep: adc0_ad3_1 {
> + atmel,pins =
> + <AT91_PIOD 23 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD23 GPIO output 0 */
> + };
> + pinctrl_adc0_ad4_sleep: adc0_ad4_1 {
> + atmel,pins =
> + <AT91_PIOD 24 AT91_PERIPH_GPIO (AT91_PINCTRL_OUTPUT | AT91_PINCTRL_OUTPUT_VAL(0))>; /* PD24 GPIO output 0 */

Please remove all these comments. The binding is good enough to
understand easily.

> + };
> + };
> +
> + board {
> + pinctrl_gpio_keys: gpio_keys {
> + atmel,pins =
> + <AT91_PIOE 27 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
> + };
> +
> + pinctrl_mmc0_cd: mmc0_cd {
> + atmel,pins =
> + <AT91_PIOD 17 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD17 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_mmc1_cd: mmc1_cd {
> + atmel,pins =
> + <AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD18 GPIO with pullup deglitch */
> + };
> +
> + pinctrl_pck0_as_audio_mck: pck0_as_audio_mck {
> + atmel,pins =
> + <AT91_PIOD 30 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD30 periph B */
> + };
> +
> + pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
> + atmel,pins =
> + <AT91_PIOD 31 AT91_PERIPH_B AT91_PINCTRL_NONE>; /* PD31 periph B ISI_MCK */
> + };
> +
> + pinctrl_sensor_reset: sensor_reset-0 {
> + atmel,pins =
> + <AT91_PIOE 24 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE24 gpio */
> + };
> +
> + pinctrl_sensor_power: sensor_power-0 {
> + atmel,pins =
> + <AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>; /* PE29 gpio */
> + };
> +
> + pinctrl_usba_vbus: usba_vbus {
> + atmel,pins =
> + <AT91_PIOD 29 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PD29 GPIO with deglitch */

Here again, all comments are not or great use: remove them.

> + };
> + };
> + };
> +
> + dbgu: serial@ffffee00 {
> + dmas = <0>, <0>; /* Do not use DMA for dbgu */
> + status = "okay";
> + };
> +
> + watchdog@fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb0: gadget@00500000 {
> + atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usba_vbus>;
> + status = "okay";
> + };
> + };
> +
> + sound {
> + compatible = "atmel,asoc-wm8904";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pck0_as_audio_mck>;
> +
> + atmel,model = "wm8904 @ SAMA5D3EK";
> + atmel,audio-routing =
> + "Headphone Jack", "HPOUTL",
> + "Headphone Jack", "HPOUTR",
> + "IN2L", "Line In Jack",
> + "IN2R", "Line In Jack",
> + "Mic", "MICBIAS",
> + "IN1L", "Mic";
> +
> + atmel,ssc-controller = <&ssc0>;
> + atmel,audio-codec = <&wm8904>;
> +
> + status = "disabled";
> + };
> +
> + /* Conflict with LCD pins */
> + gpio_keys {
> + compatible = "gpio-keys";
> + status = "okay";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_keys>;
> +
> + pb_user1 {
> + label = "pb_user1";
> + gpios = <&pioE 27 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
> + };
> + };
> +};
>

--
Nicolas Ferre

Next message: Alex Williamson: "Re: [PATCH v11 11/22] vfio iommu: Add blocking notifier to notify DMA_UNMAP"
Previous message: Stefan Wahren: "Re: [PATCH 1/2] pinctrl: bcm2835: Fix ints for GPIOs 28-31 & 46-53"
Next in thread: Sudeep Holla: "Re: [PATCH v2] ARM: at91/dt: add dts file for sama5d36ek CMP board"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]