Re: [PATCH] sdhci-esdhc-imx: fix bus-width for 1-bit operation.

From: Stefan Agner
Date: Wed Nov 16 2016 - 19:35:21 EST


On 2016-11-02 09:40, Stefan Agner wrote:
> On 2016-11-02 01:42, Dong Aisheng wrote:
>> Hi Leonardo,
>>
>> On Tue, Nov 1, 2016 at 11:58 PM, Leonardo G. Veiga <leogveiga@xxxxxxxxx> wrote:
>>> From: Leonardo Graboski Veiga <leonardo.veiga@xxxxxxxxxxx>
>>>
>>> The 1-bit operation mode, enabled by seeting the 'bus-width' property of
>>> the device tree 'esdhc' node to <1>, not work while using SD card.
>>>
>>> The behavior is only noticed when only the data pin 0 is connected to the
>>> hardware. A series of kernel errors are printed to the console, all of them
>>> returning the following error message followed by some explanation:
>>> mmcblk0: error -84 transferring data
>>>
>>> If four data lines are connected, it ignores the device-tree
>>> property and works in 4-bit mode of operation without errors. The hardware
>>> used for testing does not support 8-bit mode.
>>>
>>> Check the 'bus-width' property and if set to <1>, enable the
>>> SDHCI_QUIRK_FORCE_1_BIT_DATA quirk.
>>>
>>> Signed-off-by: Leonardo Graboski Veiga <leonardo.veiga@xxxxxxxxxxx>
>>> ---
>>> drivers/mmc/host/sdhci-esdhc-imx.c | 4 ++++
>>> 1 file changed, 4 insertions(+)
>>>
>>> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
>>> index c9fbc4c3..88d7d22 100644
>>> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
>>> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
>>> @@ -1003,6 +1003,10 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
>>> host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
>>> }
>>>
>>> + if (!of_property_read_u32(np, "bus-width", &boarddata->max_bus_width)
>>> + && boarddata->max_bus_width == 1)
>>> + host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
>>> +
>>
>> This looks like a common SDHCI driver issue that it assumes the default
>> bus-width as 4 bit if no SDHCI_QUIRK_FORCE_1_BIT_DATA specified.
>> if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
>> mmc->caps |= MMC_CAP_4_BIT_DATA;
>>
>> And I'm not sure Andrian or Ulf would like to see people keep using this quirk.
>> IMHO we probably could totally remove it since bus-width already tells
>> what the driver needs.
>
> Hm, I see what you are saying, the problem is that the core
> (sdhci_setup_host) falls back to 4-bit if SDHCI_QUIRK_FORCE_1_BIT_DATA
> is not set... Removing that should be fine for DT enabled SDHC drivers,
> since mmc_of_parse sets MMC_CAP_4_BIT_DATA. But not sure about drivers
> which parse dt on their own or still support platform data.... Those
> might rely on MMC_CAP_4_BIT_DATA being set by default...

Any thoughts on this?

Btw, I just realized that this used to work in 4.1 because back then the
device tree properties got parsed into struct esdhc_platform_data, which
does set the 1-bit quirk.. So this can be seen as a regression...

--
Stefan

>
> --
> Stefan
>
>
>
>>
>> Andrian & Ulf,
>> Comments?
>>
>>> /* call to generic mmc_of_parse to support additional capabilities */
>>> ret = mmc_of_parse(host->mmc);
>>> if (ret)
>>> --
>>> 2.7.4
>>>
>>
>> Regards
>> Dong Aisheng