Re: [PATCH v3 7/7] ARM: dts: stm32: add stm32 general purpose timer driver in DT

From: Jonathan Cameron
Date: Sat Dec 03 2016 - 09:40:44 EST

On 02/12/16 13:22, Lee Jones wrote:
> On Fri, 02 Dec 2016, Benjamin Gaignard wrote:
>
>> Add general purpose timers and it sub-nodes into DT for stm32f4.
>> Define and enable pwm1 and pwm3 for stm32f469 discovery board
>>
>> version 3:
>> - use "st,stm32-timer-trigger" in DT
>>
>> version 2:
>> - use parameters to describe hardware capabilities
>> - do not use references for pwm and iio timer subnodes
>>
>> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@xxxxxx>
>> ---
>> arch/arm/boot/dts/stm32f429.dtsi | 333 +++++++++++++++++++++++++++++++++-
>> arch/arm/boot/dts/stm32f469-disco.dts | 28 +++
>> 2 files changed, 360 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
>> index bca491d..8c50d03 100644
>> --- a/arch/arm/boot/dts/stm32f429.dtsi
>> +++ b/arch/arm/boot/dts/stm32f429.dtsi
>> @@ -48,7 +48,7 @@
>> #include "skeleton.dtsi"
>> #include "armv7-m.dtsi"
>> #include <dt-bindings/pinctrl/stm32f429-pinfunc.h>
>> -
>> +#include <dt-bindings/iio/timer/st,stm32-timer-triggers.h>
>> / {
>> clocks {
>> clk_hse: clk-hse {
>> @@ -355,6 +355,21 @@
>> slew-rate = <2>;
>> };
>> };
>> +
>> + pwm1_pins: pwm@1 {
>> + pins {
>> + pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>,
>> + <STM32F429_PB13_FUNC_TIM1_CH1N>,
>> + <STM32F429_PB12_FUNC_TIM1_BKIN>;
>> + };
>> + };
>> +
>> + pwm3_pins: pwm@3 {
>> + pins {
>> + pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>,
>> + <STM32F429_PB5_FUNC_TIM3_CH2>;
>> + };
>> + };
>> };
>>
>> rcc: rcc@40023810 {
>> @@ -426,6 +441,322 @@
>> interrupts = <80>;
>> clocks = <&rcc 0 38>;
>> };
>> +
>> + gptimer1: gptimer1@40010000 {
>
> timer@xxxxxxx
>
> Node names should be generic and not numbered.
>
> I suggest that this isn't actually a timer either. Is contains a
> timer (and a PWM), but in it's completeness it is not a timer per
> say.
That's just mean ;) At least suggest an alternative?

stm32-gptimerish-magic?


>
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40010000 0x400>;
>> + clocks = <&rcc 0 160>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm1@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + st,breakinput;
>> + st,complementary;
>> + status = "disabled";
>> + };
>> +
>> + timer1@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <27>;
>> + st,input-triggers-names = TIM5_TRGO,
>> + TIM2_TRGO,
>> + TIM4_TRGO,
>> + TIM3_TRGO;
>
> I'm still dubious with matching by strings.
>
> I'll take a look at the C code to see what the alternatives could be.
>
>> + st,output-triggers-names = TIM1_TRGO,
>> + TIM1_CH1,
>> + TIM1_CH2,
>> + TIM1_CH3,
>> + TIM1_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer2: gptimer2@40000000 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40000000 0x400>;
>> + clocks = <&rcc 0 128>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm2@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + st,32bits-counter;
>> + status = "disabled";
>> + };
>> +
>> + timer2@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <28>;
>> + st,input-triggers-names = TIM1_TRGO,
>> + TIM8_TRGO,
>> + TIM3_TRGO,
>> + TIM4_TRGO;
>> + st,output-triggers-names = TIM2_TRGO,
>> + TIM2_CH1,
>> + TIM2_CH2,
>> + TIM2_CH3,
>> + TIM2_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer3: gptimer3@40000400 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40000400 0x400>;
>> + clocks = <&rcc 0 129>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm3@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + status = "disabled";
>> + };
>> +
>> + timer3@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <29>;
>> + st,input-triggers-names = TIM1_TRGO,
>> + TIM8_TRGO,
>> + TIM5_TRGO,
>> + TIM4_TRGO;
>> + st,output-triggers-names = TIM3_TRGO,
>> + TIM3_CH1,
>> + TIM3_CH2,
>> + TIM3_CH3,
>> + TIM3_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer4: gptimer4@40000800 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40000800 0x400>;
>> + clocks = <&rcc 0 130>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm4@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + status = "disabled";
>> + };
>> +
>> + timer4@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <30>;
>> + st,input-triggers-names = TIM1_TRGO,
>> + TIM2_TRGO,
>> + TIM3_TRGO,
>> + TIM8_TRGO;
>> + st,output-triggers-names = TIM4_TRGO,
>> + TIM4_CH1,
>> + TIM4_CH2,
>> + TIM4_CH3,
>> + TIM4_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer5: gptimer5@40000C00 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40000C00 0x400>;
>> + clocks = <&rcc 0 131>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm5@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + st,32bits-counter;
>> + status = "disabled";
>> + };
>> +
>> + timer5@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <50>;
>> + st,input-triggers-names = TIM2_TRGO,
>> + TIM3_TRGO,
>> + TIM4_TRGO,
>> + TIM8_TRGO;
>> + st,output-triggers-names = TIM5_TRGO,
>> + TIM5_CH1,
>> + TIM5_CH2,
>> + TIM5_CH3,
>> + TIM5_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer6: gptimer6@40001000 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40001000 0x400>;
>> + clocks = <&rcc 0 132>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + timer6@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <54>;
>> + st,output-triggers-names = TIM6_TRGO;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer7: gptimer7@40001400 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40001400 0x400>;
>> + clocks = <&rcc 0 133>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + timer7@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <55>;
>> + st,output-triggers-names = TIM7_TRGO;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer8: gptimer8@40010400 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40010400 0x400>;
>> + clocks = <&rcc 0 161>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm8@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <4>;
>> + st,complementary;
>> + st,breakinput;
>> + status = "disabled";
>> + };
>> +
>> + timer8@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <46>;
>> + st,input-triggers-names = TIM1_TRGO,
>> + TIM2_TRGO,
>> + TIM4_TRGO,
>> + TIM5_TRGO;
>> + st,output-triggers-names = TIM8_TRGO,
>> + TIM8_CH1,
>> + TIM8_CH2,
>> + TIM8_CH3,
>> + TIM8_CH4;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer9: gptimer9@40014000 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40014000 0x400>;
>> + clocks = <&rcc 0 176>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm9@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <2>;
>> + status = "disabled";
>> + };
>> +
>> + timer9@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <24>;
>> + st,input-triggers-names = TIM2_TRGO,
>> + TIM3_TRGO;
>> + st,output-triggers-names = TIM9_TRGO,
>> + TIM9_CH1,
>> + TIM9_CH2;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer10: gptimer10@40014400 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40014400 0x400>;
>> + clocks = <&rcc 0 177>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm10@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <1>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer11: gptimer11@40014800 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40014800 0x400>;
>> + clocks = <&rcc 0 178>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm11@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <1>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer12: gptimer12@40001800 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40001800 0x400>;
>> + clocks = <&rcc 0 134>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm12@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <2>;
>> + status = "disabled";
>> + };
>> +
>> + timer12@0 {
>> + compatible = "st,stm32-timer-trigger";
>> + interrupts = <43>;
>> + st,input-triggers-names = TIM4_TRGO,
>> + TIM5_TRGO;
>> + st,output-triggers-names = TIM12_TRGO,
>> + TIM12_CH1,
>> + TIM12_CH2;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer13: gptimer13@40001C00 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40001C00 0x400>;
>> + clocks = <&rcc 0 135>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm13@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <1>;
>> + status = "disabled";
>> + };
>> + };
>> +
>> + gptimer14: gptimer14@40002000 {
>> + compatible = "st,stm32-gptimer";
>> + reg = <0x40002000 0x400>;
>> + clocks = <&rcc 0 136>;
>> + clock-names = "clk_int";
>> + status = "disabled";
>> +
>> + pwm14@0 {
>> + compatible = "st,stm32-pwm";
>> + st,pwm-num-chan = <1>;
>> + status = "disabled";
>> + };
>> + };
>> };
>> };
>>
>> diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
>> index 8a163d7..df4ca7e 100644
>> --- a/arch/arm/boot/dts/stm32f469-disco.dts
>> +++ b/arch/arm/boot/dts/stm32f469-disco.dts
>> @@ -81,3 +81,31 @@
>> &usart3 {
>> status = "okay";
>> };
>> +
>> +&gptimer1 {
>> + status = "okay";
>> +
>> + pwm1@0 {
>> + pinctrl-0 = <&pwm1_pins>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> + };
>> +
>> + timer1@0 {
>> + status = "okay";
>> + };
>> +};
>
> This is a much *better* format than before.
>
> I still don't like the '&' syntax though.
>
>> +&gptimer3 {
>> + status = "okay";
>> +
>> + pwm3@0 {
>> + pinctrl-0 = <&pwm3_pins>;
>> + pinctrl-names = "default";
>> + status = "okay";
>> + };
>> +
>> + timer3@0 {
>> + status = "okay";
>> + };
>> +};
>