RE: ATH9 driver issues on ARM64

[Bharat Kumar Gogada]

> On 08/12/16 18:33, Bharat Kumar Gogada wrote:
> >> On 08/12/16 15:29, Bharat Kumar Gogada wrote:
> >>
> >> Two things:
> >>
> >>> Here is the cat /proc/interrupts (after we do interface up):
> >>>
> >>> root@:~# ifconfig wlan0 up
> >>> [ 1548.926601] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> >>> root@Xilinx-ZCU102-2016_3:~# cat /proc/interrupts
> >>>            CPU0       CPU1       CPU2       CPU3
> >>>   1:          0          0          0          0     GICv2  29 Edge      arch_timer
> >>>   2:      19873      20058      19089      17435     GICv2  30 Edge      arch_timer
> 
> By the way, please use a recent kernel. Seeing edge here means you're running
> with something that is a bit old (and broken). And since you haven't even said
> what revision of the kernel you're using, hslping you is not an easy task. tglx told
> you something similar about a week ago.
> 
> >>>  12:          0          0          0          0     GICv2 156 Level     zynqmp-dma
> >>>  13:          0          0          0          0     GICv2 157 Level     zynqmp-dma
> >>>  14:          0          0          0          0     GICv2 158 Level     zynqmp-dma
> >>>  15:          0          0          0          0     GICv2 159 Level     zynqmp-dma
> >>>  16:          0          0          0          0     GICv2 160 Level     zynqmp-dma
> >>>  17:          0          0          0          0     GICv2 161 Level     zynqmp-dma
> >>>  18:          0          0          0          0     GICv2 162 Level     zynqmp-dma
> >>>  19:          0          0          0          0     GICv2 163 Level     zynqmp-dma
> >>>  20:          0          0          0          0     GICv2 164 Level     Mali_GP_MMU,
> Mali_GP,
> >> Mali_PP0_MMU, Mali_PP0, Mali_PP1_MMU, Mali_PP1
> >>
> >> I'm not even going to consider looking at something that is running
> >> out of tree code. So please start things with a fresh kernel that
> >> doesn't contain stuff we can't debug.
> >>
> > Ok will test with fresh kernel.
> >
> >>>  30:          0          0          0          0     GICv2  95 Level     eth0, eth0
> >>> 206:        314          0          0          0     GICv2  49 Level     cdns-i2c
> >>> 207:         40          0          0          0     GICv2  50 Level     cdns-i2c
> >>> 209:          0          0          0          0     GICv2 150 Level     nwl_pcie:misc
This irq line is handling miscellaneous interrupts this shows level triggered. 
> >>> 214:         12          0          0          0     GICv2  47 Level     ff0f0000.spi
> >>> 215:          0          0          0          0     GICv2  58 Level     ffa60000.rtc
> >>> 216:          0          0          0          0     GICv2  59 Level     ffa60000.rtc
> >>> 217:          0          0          0          0     GICv2 165 Level     ahci-
> ceva[fd0c0000.ahci]
> >>> 218:         61          0          0          0     GICv2  81 Level     mmc0
> >>> 219:          0          0          0          0     GICv2 187 Level     arm-smmu global fault
> >>> 220:        471          0          0          0     GICv2  53 Level     xuartps
> >>> 223:          0          0          0          0     GICv2 154 Level     fd4c0000.dma
> >>> 224:          3          0          0          0     dummy   1 Edge      ath9k
> >>
> >> What is this "dummy" controller? And if that's supposed to be a
> >> legacy interrupt from the PCI device, it has the wrong trigger.
> >
> > Yes it is for legacy interrupt, wrong trigger means ?
> 
> Aren't legacy interrupts supposed to be *level* triggered, and not edge?
> 
Yes agreed.
For legacy interrupts im using irq_set_chained_handler_and_data so the irq line between bridge and GIC
Will not be shown here. The above how is virq for legacy, which is given by kernel, not sure why its state is set
to edge.


Thanks & Regards,
Bharat