Re: [PATCH v6 4/9] dt-bindings: iio: iio-mux: document iio-mux bindings

[Jonathan Cameron]

On 06/12/16 09:18, Peter Rosin wrote:
> On 2016-12-06 00:26, Rob Herring wrote:
>> On Wed, Nov 30, 2016 at 09:16:58AM +0100, Peter Rosin wrote:
>>> Signed-off-by: Peter Rosin <peda@xxxxxxxxxx>
>>> ---
>>>  .../bindings/iio/multiplexer/iio-mux.txt           | 40 ++++++++++++++++++++++
>>>  MAINTAINERS                                        |  6 ++++
>>>  2 files changed, 46 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/iio/multiplexer/iio-mux.txt
>>
>> I'm still not convinced about this binding, but don't really have more 
>> comments ATM. Sending 6 versions in 2 weeks or so doesn't really help 
>> either.
> 
> Sorry about the noise, I'll try to be more careful going forward. On
> the flip side, I haven't touched the code since v6.
> 
> I don't see how bindings that are as flexible as the current (and
> original) phandle link between the mux consumer and the mux controller
> would look, and at the same time be simpler to understand. You need
> to be able to refer to a mux controller from several mux consumers, and
> you need to support several mux controllers in one node (the ADG792A
> case). And, AFAICT, the complex case wasn't really the problem, it was
> that it is overly complex to describe the simple case of one mux
> consumer and one mux controller. But in your comment for v2 [1] you
> said that I was working around limitations with shared GPIO pins. But
> solving that in the GPIO subsystem would not solve all that the
> phandle approach is solving, since you would not have support for
> ADG792A (or other non-GPIO controlled muxes). So, I think listing
> the gpio pins inside the mux consumer node is a non-starter, the mux
> controller has to live in its own node with its own compatible.
> 
> Would you be happier if I managed to marry the phandle approach with
> the option of having the mux controller as a child node of the mux
> consumer for the simple case?
> 
> I added an example at the end of this message (the same as the first
> example in v4 [2], at least in principle) for easy comparison between
> the phandle and the controller-in-child-node approaches. I can't say
> that I personally find the difference all that significant, and do not
> think it is worth it. As I see it, the "simple option" would just muddy
> the waters...
> 
> [1] http://marc.info/?l=linux-kernel&m=147948334204795&w=2
> [2] http://marc.info/?l=linux-kernel&m=148001364904240&w=2
> 
>>> diff --git a/Documentation/devicetree/bindings/iio/multiplexer/iio-mux.txt b/Documentation/devicetree/bindings/iio/multiplexer/iio-mux.txt
>>> new file mode 100644
>>> index 000000000000..8080cf790d82
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/iio/multiplexer/iio-mux.txt
>>> @@ -0,0 +1,40 @@
>>> +IIO multiplexer bindings
>>> +
>>> +If a multiplexer is used to select which hardware signal is fed to
>>> +e.g. an ADC channel, these bindings describe that situation.
>>> +
>>> +Required properties:
>>> +- compatible : "iio-mux"
>>
>> This is a Linuxism. perhaps "adc-mux".
> 
> No, that's not general enough, it could just as well be used to mux a
> temperature sensor. Or whatever. Hmmm, given that "iio-mux" is bad, perhaps
> "io-channel-mux" is better? That matches the io-channels property used to
> refer to the parent channel.
analog-mux maybe? Makes more sense out of context (though with io-channels defined on
the next line you have plenty of context here ;)
> 
>>> +- io-channels : Channel node of the parent channel that has multiplexed
>>> +		input.
>>> +- io-channel-names : Should be "parent".
>>> +- #address-cells = <1>;
>>> +- #size-cells = <0>;
>>> +- mux-controls : Mux controller node to use for operating the mux
>>> +- channels : List of strings, labeling the mux controller states.
>>> +
>>> +The multiplexer state as described in ../misc/mux-controller.txt
>>> +
>>> +For each non-empty string in the channels property, an iio channel will
>>> +be created. The number of this iio channel is the same as the index into
>>> +the list of strings in the channels property, and also matches the mux
>>> +controller state.
>>> +
>>> +Example:
>>> +	mux: mux-controller {
>>> +		compatible = "mux-gpio";
>>> +		#mux-control-cells = <0>;
>>> +
>>> +		mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
>>> +			    <&pioA 1 GPIO_ACTIVE_HIGH>;
>>> +	};
>>> +
>>> +	adc-mux {
>>> +		compatible = "iio-mux";
>>> +		io-channels = <&adc 0>;
>>> +		io-channel-names = "parent";
>>> +
>>> +		mux-controls = <&mux>;
>>> +
>>> +		channels = "sync", "in", system-regulator";
>>> +	};
> 
> Describing the same as above, but with the mux controller as a child
> node.
> 
> 	adc-mux {
> 		compatible = "iio-mux";
> 		io-channels = <&adc 0>;
> 		io-channel-names = "parent";
> 
> 		channels = "sync", "in", system-regulator";
> 
> 		mux-controller {
> 			compatible = "mux-gpio";
> 
> 			mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>,
> 				    <&pioA 1 GPIO_ACTIVE_HIGH>;
> 		};
> 	};
> 
> Cheers,
> Peter
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>