Re: [PATCH v5 2/2] mmc: sdhci-cadence: add Cadence SD4HC support

[Rob Herring]

On Thu, Dec 08, 2016 at 09:50:55PM +0900, Masahiro Yamada wrote:
> Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
> 
> For SD, it basically relies on the SDHCI standard code.
> For eMMC, this driver provides some callbacks to support the
> hardware part that is specific to this IP design.
> 
> Signed-off-by: Masahiro Yamada <yamada.masahiro@xxxxxxxxxxxxx>
> Acked-by: Adrian Hunter <adrian.hunter@xxxxxxxxx>
> ---
> 
> Changes in v5:
>   - Fix calculation of the center of the tuned window
> 
> Changes in v4:
>   - Override mmc_host_ops.execute_tuning instead of the
>     .platform_execute_tuning implementation
> 
> Changes in v3:
>   - Remove unneeded explanation about HRS and SRS from DT binding;
>     the offsets to HRS/SRS are fixed for this hardware and this is
>     quite normal, like each hardware has a fixed register view except
>     the register base.  The detailed register map is what the driver
>     cares about, so no need to explain it in the binding.
> 
> Changes in v2:
>   - Remove unnecessary "select MMC_SDHCI_IO_ACCESSORS"
> 
>  .../devicetree/bindings/mmc/sdhci-cadence.txt      |  30 +++
>  drivers/mmc/host/Kconfig                           |  11 +
>  drivers/mmc/host/Makefile                          |   1 +
>  drivers/mmc/host/sdhci-cadence.c                   | 283 +++++++++++++++++++++
>  4 files changed, 325 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mmc/sdhci-cadence.txt
>  create mode 100644 drivers/mmc/host/sdhci-cadence.c
> 
> diff --git a/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt
> new file mode 100644
> index 0000000..750374f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/sdhci-cadence.txt
> @@ -0,0 +1,30 @@
> +* Cadence SD/SDIO/eMMC Host Controller
> +
> +Required properties:
> +- compatible: should be "cdns,sd4hc".

Needs SoC specific compatible strings too.

> +- reg: offset and length of the register set for the device.
> +- interrupts: a single interrupt specifier.
> +- clocks: phandle to the input clock.
> +
> +Optional properties:
> +For eMMC configuration, supported speed modes are not indicated by the SDHCI
> +Capabilities Register.  Instead, the following properties should be specified
> +if supported.  See mmc.txt for details.
> +- mmc-ddr-1_8v
> +- mmc-ddr-1_2v
> +- mmc-hs200-1_8v
> +- mmc-hs200-1_2v
> +- mmc-hs400-1_8v
> +- mmc-hs400-1_2v

There's now a property to override SDHCI capabilities register. Maybe 
you should use that instead? I'll defer to Ulf.

> +
> +Example:
> +	emmc: sdhci@5a000000 {
> +		compatible = "cdns,sd4hc";
> +		reg = <0x5a000000 0x400>;
> +		interrupts = <0 78 4>;
> +		clocks = <&clk 4>;
> +		bus-width = <8>;
> +		mmc-ddr-1_8v;
> +		mmc-hs200-1_8v;
> +		mmc-hs400-1_8v;
> +	};