Re: [PATCH v6 2/5] i2c: Add STM32F4 I2C driver
From: M'boumba Cedric Madianga
Date: Thu Dec 15 2016 - 10:28:20 EST
Hello,
Thanks for this review, it will help.
2016-12-13 10:20 GMT+01:00 Uwe Kleine-KÃnig <u.kleine-koenig@xxxxxxxxxxxxxx>:
> Hello,
>
> On Mon, Dec 12, 2016 at 05:15:39PM +0100, M'boumba Cedric Madianga wrote:
>> This patch adds support for the STM32F4 I2C controller.
>>
>> Signed-off-by: M'boumba Cedric Madianga <cedric.madianga@xxxxxxxxx>
>> ---
>> drivers/i2c/busses/Kconfig | 10 +
>> drivers/i2c/busses/Makefile | 1 +
>> drivers/i2c/busses/i2c-stm32f4.c | 849 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 860 insertions(+)
>> create mode 100644 drivers/i2c/busses/i2c-stm32f4.c
>>
>> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
>> index 0cdc844..2719208 100644
>> --- a/drivers/i2c/busses/Kconfig
>> +++ b/drivers/i2c/busses/Kconfig
>> @@ -886,6 +886,16 @@ config I2C_ST
>> This driver can also be built as module. If so, the module
>> will be called i2c-st.
>>
>> +config I2C_STM32F4
>> + tristate "STMicroelectronics STM32F4 I2C support"
>> + depends on ARCH_STM32 || COMPILE_TEST
>> + help
>> + Enable this option to add support for STM32 I2C controller embedded
>> + in STM32F4 SoCs.
>> +
>> + This driver can also be built as module. If so, the module
>> + will be called i2c-stm32f4.
>> +
>> config I2C_STU300
>> tristate "ST Microelectronics DDC I2C interface"
>> depends on MACH_U300
>> diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
>> index 1c1bac8..a2c6ff5 100644
>> --- a/drivers/i2c/busses/Makefile
>> +++ b/drivers/i2c/busses/Makefile
>> @@ -85,6 +85,7 @@ obj-$(CONFIG_I2C_SH_MOBILE) += i2c-sh_mobile.o
>> obj-$(CONFIG_I2C_SIMTEC) += i2c-simtec.o
>> obj-$(CONFIG_I2C_SIRF) += i2c-sirf.o
>> obj-$(CONFIG_I2C_ST) += i2c-st.o
>> +obj-$(CONFIG_I2C_STM32F4) += i2c-stm32f4.o
>> obj-$(CONFIG_I2C_STU300) += i2c-stu300.o
>> obj-$(CONFIG_I2C_SUN6I_P2WI) += i2c-sun6i-p2wi.o
>> obj-$(CONFIG_I2C_TEGRA) += i2c-tegra.o
>> diff --git a/drivers/i2c/busses/i2c-stm32f4.c b/drivers/i2c/busses/i2c-stm32f4.c
>> new file mode 100644
>> index 0000000..89ad579
>> --- /dev/null
>> +++ b/drivers/i2c/busses/i2c-stm32f4.c
>> @@ -0,0 +1,849 @@
>> +/*
>> + * Driver for STMicroelectronics STM32 I2C controller
>> + *
>> + * Copyright (C) M'boumba Cedric Madianga 2015
>> + * Author: M'boumba Cedric Madianga <cedric.madianga@xxxxxxxxx>
>> + *
>> + * This driver is based on i2c-st.c
>> + *
>> + * License terms: GNU General Public License (GPL), version 2
>> + */
>
> If there is a public description available for the device, a link here
> would be great.
The device is described in the reference manual of the STM32F429/439 SoC.
As this reference manual is public, I will add it at the beginning of
the driver as requested.
>
>> +
>> +#include <linux/clk.h>
>> +#include <linux/delay.h>
>> +#include <linux/err.h>
>> +#include <linux/i2c.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/module.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/of.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/reset.h>
>> +
>> +/* STM32F4 I2C offset registers */
>> +#define STM32F4_I2C_CR1 0x00
>> +#define STM32F4_I2C_CR2 0x04
>> +#define STM32F4_I2C_DR 0x10
>> +#define STM32F4_I2C_SR1 0x14
>> +#define STM32F4_I2C_SR2 0x18
>> +#define STM32F4_I2C_CCR 0x1C
>> +#define STM32F4_I2C_TRISE 0x20
>> +#define STM32F4_I2C_FLTR 0x24
>> +
>> +/* STM32F4 I2C control 1*/
>> +#define STM32F4_I2C_CR1_SWRST BIT(15)
>> +#define STM32F4_I2C_CR1_POS BIT(11)
>> +#define STM32F4_I2C_CR1_ACK BIT(10)
>> +#define STM32F4_I2C_CR1_STOP BIT(9)
>> +#define STM32F4_I2C_CR1_START BIT(8)
>> +#define STM32F4_I2C_CR1_PE BIT(0)
>> +
>> +/* STM32F4 I2C control 2 */
>> +#define STM32F4_I2C_CR2_FREQ_MASK GENMASK(5, 0)
>> +#define STM32F4_I2C_CR2_FREQ(n) ((n & STM32F4_I2C_CR2_FREQ_MASK))
>
> This should better be ((n) & STM32F4_I2C_CR2_FREQ_MASK). There a few
> more constants that need the same fix.
OK I will fix it in the V7. Thanks.
>
>> +#define STM32F4_I2C_CR2_ITBUFEN BIT(10)
>> +#define STM32F4_I2C_CR2_ITEVTEN BIT(9)
>> +#define STM32F4_I2C_CR2_ITERREN BIT(8)
>> +#define STM32F4_I2C_CR2_IRQ_MASK (STM32F4_I2C_CR2_ITBUFEN \
>> + | STM32F4_I2C_CR2_ITEVTEN \
>> + | STM32F4_I2C_CR2_ITERREN)
>
> I'd layout this like:
>
> #define STM32F4_I2C_CR2_IRQ_MASK (STM32F4_I2C_CR2_ITBUFEN | \
> STM32F4_I2C_CR2_ITEVTEN | \
> STM32F4_I2C_CR2_ITERREN)
>
> which is more usual I think.
OK I will fix it in the V7. Thanks.
>
>> +/* STM32F4 I2C Status 1 */
>> +#define STM32F4_I2C_SR1_AF BIT(10)
>> +#define STM32F4_I2C_SR1_ARLO BIT(9)
>> +#define STM32F4_I2C_SR1_BERR BIT(8)
>> +#define STM32F4_I2C_SR1_TXE BIT(7)
>> +#define STM32F4_I2C_SR1_RXNE BIT(6)
>> +#define STM32F4_I2C_SR1_BTF BIT(2)
>> +#define STM32F4_I2C_SR1_ADDR BIT(1)
>> +#define STM32F4_I2C_SR1_SB BIT(0)
>> +#define STM32F4_I2C_SR1_ITEVTEN_MASK (STM32F4_I2C_SR1_BTF \
>> + | STM32F4_I2C_SR1_ADDR \
>> + | STM32F4_I2C_SR1_SB)
>> +#define STM32F4_I2C_SR1_ITBUFEN_MASK (STM32F4_I2C_SR1_TXE \
>> + | STM32F4_I2C_SR1_RXNE)
>> +#define STM32F4_I2C_SR1_ITERREN_MASK (STM32F4_I2C_SR1_AF \
>> + | STM32F4_I2C_SR1_ARLO \
>> + | STM32F4_I2C_SR1_BERR)
>> +
>> +/* STM32F4 I2C Status 2 */
>> +#define STM32F4_I2C_SR2_BUSY BIT(1)
>> +
>> +/* STM32F4 I2C Control Clock */
>> +#define STM32F4_I2C_CCR_CCR_MASK GENMASK(11, 0)
>> +#define STM32F4_I2C_CCR_CCR(n) ((n & STM32F4_I2C_CCR_CCR_MASK))
>> +#define STM32F4_I2C_CCR_FS BIT(15)
>> +#define STM32F4_I2C_CCR_DUTY BIT(14)
>> +
>> +/* STM32F4 I2C Trise */
>> +#define STM32F4_I2C_TRISE_VALUE_MASK GENMASK(5, 0)
>> +#define STM32F4_I2C_TRISE_VALUE(n) ((n & STM32F4_I2C_TRISE_VALUE_MASK))
>> +
>> +/* STM32F4 I2C Filter */
>> +#define STM32F4_I2C_FLTR_DNF_MASK GENMASK(3, 0)
>> +#define STM32F4_I2C_FLTR_DNF(n) ((n & STM32F4_I2C_FLTR_DNF_MASK))
>> +#define STM32F4_I2C_FLTR_ANOFF BIT(4)
>> +
>> +#define STM32F4_I2C_MIN_FREQ 2U
>> +#define STM32F4_I2C_MAX_FREQ 42U
>> +#define FAST_MODE_MAX_RISE_TIME 1000
>> +#define STD_MODE_MAX_RISE_TIME 300
>
> Are these supposed to be the values "rise time of both SDA and SCL
> signals" from the i2c specification? If so, you got it wrong, fast mode
> has the smaller value.
Yes you are right. My mistake. Thanks
> Maybe these constants could get a home in a more central place?
Yes we probably could add these constants in a include file like i2c.h
or someting like that.
Wolfram, what is your opinion regarding this proposal ?
> Also I'd add /* ns */ to the definition.
Ok
>
>> +#define MHZ_TO_HZ 1000000
>> +
>> +enum stm32f4_i2c_speed {
>> + STM32F4_I2C_SPEED_STANDARD, /* 100 kHz */
>> + STM32F4_I2C_SPEED_FAST, /* 400 kHz */
>> + STM32F4_I2C_SPEED_END,
>> +};
>> +
>> +/**
>> + * struct stm32f4_i2c_timings - per-Mode tuning parameters
>> + * @duty: Fast mode duty cycle
>> + * @mul_ccr: Value to be multiplied to CCR to reach 100Khz/400Khz SCL frequency
>> + * @min_ccr: Minimum clock ctrl reg value to reach 100Khz/400Khz SCL frequency
>> + */
>> +struct stm32f4_i2c_timings {
>> + u32 rate;
>
> rate is undocumented and unused.
Good point. I will remove it. Thanks.
>
>> + u32 duty;
>> + u32 mul_ccr;
>> + u32 min_ccr;
>> +};
>> +
>> +/**
>> + * struct stm32f4_i2c_msg - client specific data
>> + * @addr: 8-bit slave addr, including r/w bit
>> + * @count: number of bytes to be transferred
>> + * @buf: data buffer
>> + * @result: result of the transfer
>> + * @stop: last I2C msg to be sent, i.e. STOP to be generated
>> + */
>> +struct stm32f4_i2c_msg {
>> + u8 addr;
>> + u32 count;
>> + u8 *buf;
>> + int result;
>> + bool stop;
>> +};
>> +
>> +/**
>> + * struct stm32f4_i2c_dev - private data of the controller
>> + * @adap: I2C adapter for this controller
>> + * @dev: device for this controller
>> + * @base: virtual memory area
>> + * @complete: completion of I2C message
>> + * @irq_event: interrupt event line for the controller
>> + * @irq_error: interrupt error line for the controller
>> + * @clk: hw i2c clock
>> + * speed: I2C clock frequency of the controller. Standard or Fast only supported
>> + * @msg: I2C transfer information
>> + */
>> +struct stm32f4_i2c_dev {
>> + struct i2c_adapter adap;
>> + struct device *dev;
>> + void __iomem *base;
>> + struct completion complete;
>> + int irq_event;
>> + int irq_error;
>
> You only use irq_event in the probe function. So there is no need to
> remember this one and you could use a local variable instead.
Ok, I will fix it in the V7. Thanks
>
>> + struct clk *clk;
>> + int speed;
>> + struct stm32f4_i2c_msg msg;
>> +};
>> +
>> +static struct stm32f4_i2c_timings i2c_timings[] = {
>> + [STM32F4_I2C_SPEED_STANDARD] = {
>> + .mul_ccr = 1,
>> + .min_ccr = 4,
>> + .duty = 0,
>> + },
>> + [STM32F4_I2C_SPEED_FAST] = {
>> + .mul_ccr = 16,
>> + .min_ccr = 1,
>> + .duty = 1,
>> + },
>
> Are these values from the datasheet?
Yes, these values come from I2C IP datasheet.
>
>> +};
>> +
>> +static inline void stm32f4_i2c_set_bits(void __iomem *reg, u32 mask)
>> +{
>> + writel_relaxed(readl_relaxed(reg) | mask, reg);
>> +}
>> +
>> +static inline void stm32f4_i2c_clr_bits(void __iomem *reg, u32 mask)
>> +{
>> + writel_relaxed(readl_relaxed(reg) & ~mask, reg);
>> +}
>> +
>> +static void stm32f4_i2c_soft_reset(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR1;
>> +
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_SWRST);
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_SWRST);
>
> Not very critical, but you're doing an unneeded register access here
> because the register is read twice.
>
> Also I think readability would improve if you dropped
> stm32f4_i2c_{set,clr}_bits and do their logic explicitly in the callers.
>
> stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_SWRST);
> stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_SWRST);
>
> vs
>
> val = readl_relaxed(reg);
> writel_relaxed(val | STM32F4_I2C_CR1_SWRST, reg);
> writel_relaxed(val, reg);
>
If it is just for this function, I don't have any objection to use
your proposal.
But if your request, it is to drop all calls of
stm32f4_i2c_{set,clr}_bits, I am wondering if it is something really
critical ?
Indeed, this is a big impact in this driver and I would prefer to avoid it.
>> +}
>> +
>> +static void stm32f4_i2c_disable_it(struct stm32f4_i2c_dev *i2c_dev)
>
> What is "it"? If it stands for "interrupt" the more usual abbrev is
> "irq".
Yes it stands for interrupt.
So, I will replace it by irq in the next version.
>
>> +{
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
>> +
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_IRQ_MASK);
>> +}
>> +
>> +static void stm32f4_i2c_set_periph_clk_freq(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 clk_rate, cr2, freq;
>> +
>> + cr2 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR2);
>> + cr2 &= ~STM32F4_I2C_CR2_FREQ_MASK;
>> + clk_rate = clk_get_rate(i2c_dev->clk);
>> + freq = clk_rate / MHZ_TO_HZ;
>> + freq = clamp(freq, STM32F4_I2C_MIN_FREQ, STM32F4_I2C_MAX_FREQ);
>> + cr2 |= STM32F4_I2C_CR2_FREQ(freq);
>> + writel_relaxed(cr2, i2c_dev->base + STM32F4_I2C_CR2);
>
> Can you quote the data sheet enough in a comment here to make it obvious
> that your calculation is right?
Ok I will add it.
>
> Would it be more sensible to error out if clk_rate / MHZ_TO_HZ isn't in
> the interval [STM32F4_I2C_MIN_FREQ, STM32F4_I2C_MAX_FREQ]?
Yes, input clock must be between 2 MHz and 42 Mhz to achieve standard
or fast mode mode IÂC frequencies.
If it is not the case, the I2C signal integrity is not guarantee and
could lead to communication issue between devices on the I2C bus.
>
> Usually I would expect that you need to use
> DIV_ROUND_UP(clk_rate, MHZ_TO_HZ) instead of a plain division.
Ok, I will use this macro in the next version
>
>> +}
>> +
>> +static void stm32f4_i2c_set_rise_time(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 trise, freq, cr2, val;
>> +
>> + cr2 = readl_relaxed(i2c_dev->base + STM32F4_I2C_CR2);
>> + freq = cr2 & STM32F4_I2C_CR2_FREQ_MASK;
>> +
>> + trise = readl_relaxed(i2c_dev->base + STM32F4_I2C_TRISE);
>> + trise &= ~STM32F4_I2C_TRISE_VALUE_MASK;
>
> Are you required to use rmw for STM32F4_I2C_TRISE? I'd prefer
>
> writel_relaxed(STM32F4_I2C_TRISE_VALUE(..), i2c_dev->base + STM32F4_I2C_TRISE);
>
> unless the datasheet requires rmw.
>
>> + /* Maximum rise time computation */
>> + if (i2c_dev->speed == STM32F4_I2C_SPEED_STANDARD) {
>> + trise |= STM32F4_I2C_TRISE_VALUE((freq + 1));
>
> A single pair of parenthesis is enough when you fix
> STM32F4_I2C_TRISE_VALUE as suggested above.
The datasheet does not required to use rmw so I will use your proposal
in the next version. Thanks.
>
>> + } else {
>> + val = freq * FAST_MODE_MAX_RISE_TIME / STD_MODE_MAX_RISE_TIME;
>> + trise |= STM32F4_I2C_TRISE_VALUE((val + 1));
>
> val could be local to this branch.
>
> Or make it shorter using:
>
> freq = cr2 & STM32F4_I2C_CR2_FREQ_MASK;
> if (i2c_dev->speed == STM32F4_I2C_SPEED_FAST)
> freq = freq * FAST_MODE_MAX_RISE_TIME / STD_MODE_MAX_RISE_TIME;
>
> writel_relaxed(STM32F4_I2C_TRISE_VALUE(freq + 1), ...);
>
> A quote from the data sheet about the algorithm would be good here, too.
Ok, I will use a shorter way to compute freq and add a quote from the datasheet
>
>> + }
>> +
>> + writel_relaxed(trise, i2c_dev->base + STM32F4_I2C_TRISE);
>> +}
>> +
>> +static void stm32f4_i2c_set_speed_mode(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_timings *t = &i2c_timings[i2c_dev->speed];
>> + u32 ccr, clk_rate;
>> + int val;
>> +
>> + ccr = readl_relaxed(i2c_dev->base + STM32F4_I2C_CCR);
>> + ccr &= ~(STM32F4_I2C_CCR_FS | STM32F4_I2C_CCR_DUTY |
>> + STM32F4_I2C_CCR_CCR_MASK);
>> +
>> + clk_rate = clk_get_rate(i2c_dev->clk);
>> + val = clk_rate / MHZ_TO_HZ * t->mul_ccr;
>
> Is the rounding done right? Again please describe the hardware in a
> comment.
Ok I will use DIV_ROUND_UP here and add a comment from datasheet
>
>> + if (val < t->min_ccr)
>> + val = t->min_ccr;
>> + ccr |= STM32F4_I2C_CCR_CCR(val);
>> +
>> + if (t->duty)
>> + ccr |= STM32F4_I2C_CCR_FS | STM32F4_I2C_CCR_DUTY;
>> +
>> + writel_relaxed(ccr, i2c_dev->base + STM32F4_I2C_CCR);
>> +}
>> +[...]
>> +
>> +static int stm32f4_i2c_wait_free_bus(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + u32 status;
>> + int ret;
>> +
>> + ret = readl_relaxed_poll_timeout(i2c_dev->base + STM32F4_I2C_SR2,
>> + status,
>> + !(status & STM32F4_I2C_SR2_BUSY),
>> + 10, 1000);
>> + if (ret) {
>> + dev_err(i2c_dev->dev, "bus not free\n");
>> + ret = -EBUSY;
>
> I'm not sure if "bus not free" deserves an error message. Wolfram?
>
>> + }
>> +
>> + return ret;
>> +}
>> +
>> +[...]
>> +static void stm32f4_i2c_read_msg(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
>> + u32 rbuf;
>> +
>> + rbuf = readl_relaxed(i2c_dev->base + STM32F4_I2C_DR);
>> + *msg->buf++ = (u8)rbuf & 0xff;
>
> unneeded cast (or unneeded & 0xff).
Ok thanks
>
>> + msg->count--;
>> +}
>> +
>> +[...]
>> +/**
>> + * stm32f4_i2c_handle_read() - Handle FIFO empty interrupt in case of read
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_handle_read(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
>> + void __iomem *reg = i2c_dev->base + STM32F4_I2C_CR2;
>> +
>> + switch (msg->count) {
>> + case 1:
>> + stm32f4_i2c_disable_it(i2c_dev);
>> + stm32f4_i2c_read_msg(i2c_dev);
>> + complete(&i2c_dev->complete);
>> + break;
>> + case 2:
>> + case 3:
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
>> + break;
>> + default:
>> + stm32f4_i2c_read_msg(i2c_dev);
>> + }
>
> It looks wrong that you don't call stm32f4_i2c_read_msg if msg->count is
> 2 or 3. I guess that's because these cases are handled in
> stm32f4_i2c_handle_rx_btf? Maybe you can simplify the logic a bit?
stm32f4_i2c_handle_read is called when RXNE bit is set due to new data
present in DR register.
stm32f4_i2c_handle_rx_btf is called when BTF bit is set.
This bit is set when there is new data in shift register whereas data
in DR register has not been read yet.
The datasheet requires to wait for BTF bit for 2 byte reception and
for the 3 last bytes to be read for N bytes reception (with N > 2)
That's why, in these cases (2 and 3), I clear the ITBUF interrupt in
order to not be preempted again for RXNE event as I know that I have
to wait for BTF event.
So, this is not a wrong case but I will add a comment to explain that.
>
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_handle_rx_btf() - Handle byte transfer finished interrupt
>> + * in case of read
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_handle_rx_btf(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
>> + void __iomem *reg;
>> + u32 mask;
>> + int i;
>> +
>> + switch (msg->count) {
>
> I don't understand why the handling depends on the number of messages.
Please see my above comment
>
>> + case 2:
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + /* Generate STOP or REPSTART */
>
> I stumbled about "REPSTART" and would spell it out as "repeated Start".
Ok
>
>> + if (msg->stop)
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
>> + else
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
>> +
>> + /* Read two last data bytes */
>> + for (i = 2; i > 0; i--)
>> + stm32f4_i2c_read_msg(i2c_dev);
>> +
>> + /* Disable EVT and ERR interrupt */
>> + reg = i2c_dev->base + STM32F4_I2C_CR2;
>> + mask = STM32F4_I2C_CR2_ITEVTEN | STM32F4_I2C_CR2_ITERREN;
>> + stm32f4_i2c_clr_bits(reg, mask);
>> +
>> + complete(&i2c_dev->complete);
>> + break;
>> + case 3:
>> + /* Enable ACK and read data */
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
>> + stm32f4_i2c_read_msg(i2c_dev);
>> + break;
>> + default:
>> + stm32f4_i2c_read_msg(i2c_dev);
>> + }
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_handle_rx_addr() - Handle address matched interrupt in case of
>> + * master receiver
>> + * @i2c_dev: Controller's private data
>> + */
>> +static void stm32f4_i2c_handle_rx_addr(struct stm32f4_i2c_dev *i2c_dev)
>> +{
>> + struct stm32f4_i2c_msg *msg = &i2c_dev->msg;
>> + void __iomem *reg;
>> +
>> + switch (msg->count) {
>> + case 0:
>> + stm32f4_i2c_terminate_xfer(i2c_dev);
>> + /* Clear ADDR flag */
>> + readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
>> + break;
>> + case 1:
>> + /*
>> + * Single byte reception:
>> + * Enable NACK, clear ADDR flag and generate STOP or RepSTART
>> + */
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
>> + if (msg->stop)
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_STOP);
>> + else
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_START);
>> + break;
>> + case 2:
>> + /*
>> + * 2-byte reception:
>> + * Enable NACK and PEC Position Ack and clear ADDR flag
>
> What is PEC?
PEC stands for Packet Error Checking.
This feature is used is SMbus mode in order to guarantee data
integrity during an I2C transaction thanks to packet error code
comparaison.
The POS bit is used in reception to indicate that the next byte
received in the shift register will be ACK by hardware.
So, this is a wrong comment I would say POS ACK and I will fix it in
the next version.
>
>> + */
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + stm32f4_i2c_clr_bits(reg, STM32F4_I2C_CR1_ACK);
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_POS);
>> + readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
>> + break;
>> +
>> + default:
>> + /* N-byte reception: Enable ACK and clear ADDR flag */
>> + reg = i2c_dev->base + STM32F4_I2C_CR1;
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR1_ACK);
>> + readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
>> + break;
>> + }
>> +}
>> +
>> +/**
>> + * stm32f4_i2c_isr_event() - Interrupt routine for I2C bus event
>> + * @irq: interrupt number
>> + * @data: Controller's private data
>> + */
>> +static irqreturn_t stm32f4_i2c_isr_event(int irq, void *data)
>> +{
>> +[...]
>> + real_status = readl_relaxed(i2c_dev->base + STM32F4_I2C_SR1);
>
> s/real_status/status/ ?
Ok. Thanks
>
>> +
>> + if (!(real_status & possible_status)) {
>> + dev_dbg(i2c_dev->dev,
>> + "spurious evt it (status=0x%08x, ien=0x%08x)\n",
>> + real_status, ien);
>
> s/it/irq/
Ok. Thanks
>
>> + return IRQ_NONE;
>> + }
>> +
>> + /* Use __fls() to check error bits first */
>> + flag = __fls(real_status & possible_status);
>
> If you get several events reported you only handle a single one. Is this
> effective?
You are right, if several events occur, I will execute this irq
routines for each event.
I will rework this in the next version. Thanks
>
>> + switch (1 << flag) {
>> + case STM32F4_I2C_SR1_SB:
>> + stm32f4_i2c_write_byte(i2c_dev, msg->addr);
>> + break;
>> +
>> + case STM32F4_I2C_SR1_ADDR:
>> + if (msg->addr & I2C_M_RD)
>> + stm32f4_i2c_handle_rx_addr(i2c_dev);
>> + else
>> + readl_relaxed(i2c_dev->base + STM32F4_I2C_SR2);
>> +
>> + /* Enable ITBUF interrupts */
>
> What is ITBUF?
ITBUF is an interrupt generated when RxNE or TxE flag is set
>
>> + reg = i2c_dev->base + STM32F4_I2C_CR2;
>> + stm32f4_i2c_set_bits(reg, STM32F4_I2C_CR2_ITBUFEN);
>> + break;
>> +
>> + case STM32F4_I2C_SR1_BTF:
>> + if (msg->addr & I2C_M_RD)
>> + stm32f4_i2c_handle_rx_btf(i2c_dev);
>> + else
>> + stm32f4_i2c_handle_write(i2c_dev);
>> + break;
>> +
>> + case STM32F4_I2C_SR1_TXE:
>> + stm32f4_i2c_handle_write(i2c_dev);
>> + break;
>> +
>> + case STM32F4_I2C_SR1_RXNE:
>> + stm32f4_i2c_handle_read(i2c_dev);
>> + break;
>> +
>> + default:
>> + dev_err(i2c_dev->dev,
>> + "evt it unhandled: status=0x%08x)\n", real_status);
>
> s/it/irq/
ok
>
>> + return IRQ_NONE;
>> + }
>> +
>> + return IRQ_HANDLED;
>> +}
>> +
>> +[...]
>> +static int stm32f4_i2c_xfer_msg(struct stm32f4_i2c_dev *i2c_dev,
>> + struct i2c_msg *msg, bool is_first,
>> + bool is_last)
>> +{
>> +[...]
>> + /* Enable ITEVT and ITERR interrupts */
>
> This comment isn't helpful. Mentioning their meaning would be great
> instead.
ok I will add it (ITEVT = event interrupt and ITERR = error interrupt)
>
>> +[...]
>> +static int stm32f4_i2c_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg msgs[],
>> + int num)
>> +{
>> + struct stm32f4_i2c_dev *i2c_dev = i2c_get_adapdata(i2c_adap);
>> + int ret, i;
>> +
>> + ret = clk_enable(i2c_dev->clk);
>> + if (ret) {
>> + dev_err(i2c_dev->dev, "Failed to enable clock\n");
>> + return ret;
>> + }
>> +
>> + stm32f4_i2c_hw_config(i2c_dev);
>> +
>> + for (i = 0; i < num && !ret; i++)
>> + ret = stm32f4_i2c_xfer_msg(i2c_dev, &msgs[i], i == 0,
>> + i == num - 1);
>> +
>> + clk_disable(i2c_dev->clk);
>> +
>> + return (ret < 0) ? ret : i;
>
> using num instead of i would be a bit more obvious.
ok
>
>> +static int stm32f4_i2c_probe(struct platform_device *pdev)
>> +{
>> +[...]
>> + i2c_dev->speed = STM32F4_I2C_SPEED_STANDARD;
>> + ret = of_property_read_u32(np, "clock-frequency", &clk_rate);
>> + if ((!ret) && (clk_rate == 400000))
>> + i2c_dev->speed = STM32F4_I2C_SPEED_FAST;
>
> I'd use
>
> if (!ret && clk_rate >= 400000)
> i2c_dev->speed = STM32F4_I2C_SPEED_FAST;
>
> . That's less parenthesis and a more robust selection of the bus
> frequency.
ok
>
>> +
>> + i2c_dev->dev = &pdev->dev;
>> +
>> + ret = devm_request_threaded_irq(&pdev->dev, i2c_dev->irq_event,
>> + NULL, stm32f4_i2c_isr_event,
>> + IRQF_ONESHOT, pdev->name, i2c_dev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Failed to request irq %i\n",
>> + i2c_dev->irq_error);
>
> That's wrong. Requesting irq_event failed.
Ok Thanks.
>
>> + goto clk_free;
>> + }
>> +
>> + ret = devm_request_threaded_irq(&pdev->dev, i2c_dev->irq_error,
>> + NULL, stm32f4_i2c_isr_error,
>> + IRQF_ONESHOT, pdev->name, i2c_dev);
>> + if (ret) {
>> + dev_err(&pdev->dev, "Failed to request irq %i\n",
>> + i2c_dev->irq_error);
>> + goto clk_free;
>
> It would also be nice to know for which type of irq this failed. I.e.
> please point out if this is the error irq or the event irq in the
> message. Ditto for checking the return type of irq_of_parse_and_map.
Ok I will fix it in the next version.
>
>> + }
>> +
>> + adap = &i2c_dev->adap;
>> + i2c_set_adapdata(adap, i2c_dev);
>> + snprintf(adap->name, sizeof(adap->name), "STM32 I2C(%pa)", &res->start);
>> + adap->owner = THIS_MODULE;
>> + adap->timeout = 2 * HZ;
>> + adap->retries = 0;
>> + adap->algo = &stm32f4_i2c_algo;
>> + adap->dev.parent = &pdev->dev;
>> + adap->dev.of_node = pdev->dev.of_node;
>> +
>> + init_completion(&i2c_dev->complete);
>> +
>> + ret = i2c_add_adapter(adap);
>> + if (ret)
>> + goto clk_free;
>> +
>> + platform_set_drvdata(pdev, i2c_dev);
>> +
>> + dev_info(i2c_dev->dev, "STM32F4 I2C driver initialized\n");
>
> This is wrong. The driver is bound now to a device, not initialized.
Ok I will replaced initialized by registered. Thanks.
>
>> +static const struct of_device_id stm32f4_i2c_match[] = {
>> + { .compatible = "st,stm32f4-i2c", },
>> + {},
>> +};
>> +MODULE_DEVICE_TABLE(of, stm32f4_i2c_match);
>> +
>> +static struct platform_driver stm32f4_i2c_driver = {
>> + .driver = {
>> + .name = "stm32f4-i2c",
>> + .of_match_table = stm32f4_i2c_match,
>
> Is this needed?
Without of_match_table, I could not match an I2C device instance from
DT with this driver.
So maybe, there is a misunderstanding.
Could you please clarify your question ?
>
>> + },
>> + .probe = stm32f4_i2c_probe,
>> + .remove = stm32f4_i2c_remove,
>> +};
>
> Best regards
> Uwe
>
> --
> Pengutronix e.K. | Uwe Kleine-KÃnig |
> Industrial Linux Solutions | http://www.pengutronix.de/ |
Thanks again
Best regards,
Cedric