[PATCH v3 11/24] ARM: dts: imx6-sabreauto: add the ADV7180 video decoder

[Steve Longerbeam]

Enables the ADV7180 decoder sensor. The ADV7180 connects to the
parallel-bus mux input on ipu1_csi0_mux.

On the sabreauto, two analog video inputs are routed to the ADV7180,
composite on Ain1, and composite on Ain3. Those inputs are defined
via inputs and input-names under the ADV7180 node. The ADV7180 power
pin is via max7310_b port expander.

Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 61 ++++++++++++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 495709f..7999857 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -124,6 +124,24 @@
 			#size-cells = <0>;
 			reg = <1>;
 
+			adv7180: camera@21 {
+				compatible = "adi,adv7180";
+				reg = <0x21>;
+				powerdown-gpios = <&max7310_b 2 GPIO_ACTIVE_LOW>;
+				interrupt-parent = <&gpio1>;
+				interrupts = <27 0x8>;
+				inputs = <0x00 0x02>;
+				input-names = "ADV7180 Composite on Ain1",
+						"ADV7180 Composite on Ain3";
+
+				port {
+					adv7180_to_ipu1_csi0_mux: endpoint {
+						remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+						bus-width = <8>;
+					};
+				};
+			};
+
 			max7310_a: gpio@30 {
 				compatible = "maxim,max7310";
 				reg = <0x30>;
@@ -151,6 +169,25 @@
 	};
 };
 
+&ipu1_csi0_from_ipu1_csi0_mux {
+	bus-width = <8>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&adv7180_to_ipu1_csi0_mux>;
+	bus-width = <8>;
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+
+	/* enable frame interval monitor on this port */
+	fim {
+		status = "okay";
+	};
+};
+
 &clks {
 	assigned-clocks = <&clks IMX6QDL_PLL4_BYPASS_SRC>,
 			  <&clks IMX6QDL_PLL4_BYPASS>,
@@ -445,6 +482,30 @@
 			>;
 		};
 
+		pinctrl_ipu1_csi0: ipu1csi0grp {
+			fsl,pins = <
+				MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09   0x1b0b0
+				MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18  0x1b0b0
+				MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19  0x1b0b0
+				MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0
+				MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC    0x1b0b0
+				MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC   0x1b0b0
+			>;
+		};
+
 		pinctrl_max7310: max7310grp {
 			fsl,pins = <
 				MX6QDL_PAD_SD2_DAT0__GPIO1_IO15 0x1b0b0
-- 
2.7.4