Re: [PATCH v4 3/4] dt-bindings: phy: Add support for QMP phy

[Kishon Vijay Abraham I]

Hi,

On Tuesday 10 January 2017 04:21 PM, Vivek Gautam wrote:
> Qualcomm chipsets have QMP phy controller that provides
> support to a number of controller, viz. PCIe, UFS, and USB.
> Adding dt binding information for the same.
> 
> Signed-off-by: Vivek Gautam <vivek.gautam@xxxxxxxxxxxxxx>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> 
> Changes since v3:
>  - Added #clock-cells = <1>, indicating that phy is a clock provider.
> 
> Changes since v2:
>  - Removed binding for "ref_clk_src" since we don't request this
>    clock in the driver.
>  - Addressed s/ref_clk/ref. Don't need to add '_clk' suffix to clock names.
>  - Using 'phy' for the node name.
> 
> Changes since v1:
>  - New patch, forked out of the original driver patch:
>    "phy: qcom-qmp: new qmp phy driver for qcom-chipsets"
>  - Added 'Acked-by' from Rob.
>  - Updated bindings to include mem resource as a list of
>    offset - length pair for serdes block and for each lane.
>  - Added a new binding for 'lane-offsets' that contains offsets
>    to tx, rx and pcs blocks from each lane base address.
> 
>  .../devicetree/bindings/phy/qcom-qmp-phy.txt       | 76 ++++++++++++++++++++++
>  1 file changed, 76 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> new file mode 100644
> index 000000000000..6f510fe48f46
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt
> @@ -0,0 +1,76 @@
> +Qualcomm QMP PHY controller
> +===========================
> +
> +QMP phy controller supports physical layer functionality for a number of
> +controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
> +
> +Required properties:
> + - compatible: compatible list, contains:
> +	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
> +	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
> + - reg: list of offset and length pair of the PHY register sets.
> +	at index 0: offset and length of register set for PHY common
> +		    serdes block.
> +	from index 1 - N: offset and length of register set for each lane,
> +			  for N number of phy lanes (ports).
> + - lane-offsets: array of offsets to tx, rx and pcs blocks for phy lanes.
> + - #phy-cells: must be 1
> +    - Cell after phy phandle should be the port (lane) number.
> + - #clock-cells: must be 1
> +    - Phy pll outputs a bunch of clocks for Tx, Rx and Pipe
> +      interface (for pipe based PHYs). These clock are then gate-controlled
> +      by gcc.
> + - clocks: a list of phandles and clock-specifier pairs,
> +	   one for each entry in clock-names.
> + - clock-names: must be "cfg_ahb" for phy config clock,
> +			"aux" for phy aux clock,
> +			"ref" for 19.2 MHz ref clk,
> +			"pipe<port-number>" for pipe clock specific to
> +			each port/lane (Optional).
> + - resets: a list of phandles and reset controller specifier pairs,
> +	   one for each entry in reset-names.
> + - reset-names: must be "phy" for reset of phy block,
> +			"common" for phy common block reset,
> +			"cfg" for phy's ahb cfg block reset (Optional).
> +			"port<port-number>" for reset specific to
> +			each port/lane (Optional).
> + - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
> + - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
> +
> +Optional properties:
> + - vddp-ref-clk-supply: Phandle to a regulator supply to any specific refclk
> +			pll block.
> +
> +Example:
> +	pcie_phy: phy@34000 {
> +		compatible = "qcom,msm8996-qmp-pcie-phy";
> +		reg = <0x034000 0x48f>,
> +			<0x035000 0x5bf>,
> +			<0x036000 0x5bf>,
> +			<0x037000 0x5bf>;
> +				/* tx, rx, pcs */
> +		lane-offsets = <0x0 0x200 0x400>;
> +		#phy-cells = <1>;
> +		#clock-cells = <1>;
> +
> +		clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
> +			<&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
> +			<&gcc GCC_PCIE_CLKREF_CLK>,
> +			<&gcc GCC_PCIE_0_PIPE_CLK>,
> +			<&gcc GCC_PCIE_1_PIPE_CLK>,
> +			<&gcc GCC_PCIE_2_PIPE_CLK>;
> +		clock-names = "aux", "cfg_ahb", "ref",
> +				"pipe0", "pipe1", "pipe2";
> +
> +		vdda-phy-supply = <&pm8994_l28>;
> +		vdda-pll-supply = <&pm8994_l12>;
> +
> +		resets = <&gcc GCC_PCIE_PHY_BCR>,
> +			<&gcc GCC_PCIE_PHY_COM_BCR>,
> +			<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>,
> +			<&gcc GCC_PCIE_0_PHY_BCR>,
> +			<&gcc GCC_PCIE_1_PHY_BCR>,
> +			<&gcc GCC_PCIE_2_PHY_BCR>;
> +		reset-names = "phy", "common", "cfg",
> +				"lane0", "lane1", "lane2";

Each lane has a separate clock, separate reset.. why not create sub-nodes for
each lane?

Thanks
Kishon