[PATCH v3 18/18] drivers/fsi: Add GPIO based FSI master

[Christopher Bostic]

From: Chris Bostic <cbostic@xxxxxxxxxx>

Implement a FSI master using GPIO.  Will generate FSI protocol for
read and write commands to particular addresses.  Sends master command
and waits for and decodes a slave response.

Includes Jeremy Kerr's original GPIO master base commit.

Signed-off-by: Jeremy Kerr <jk@xxxxxxxxxx>
Signed-off-by: Chris Bostic <cbostic@xxxxxxxxxx>
---
 drivers/fsi/Kconfig           |  11 +
 drivers/fsi/Makefile          |   1 +
 drivers/fsi/fsi-master-gpio.c | 530 ++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 542 insertions(+)
 create mode 100644 drivers/fsi/fsi-master-gpio.c

diff --git a/drivers/fsi/Kconfig b/drivers/fsi/Kconfig
index 04c1a0e..9cf8345 100644
--- a/drivers/fsi/Kconfig
+++ b/drivers/fsi/Kconfig
@@ -9,4 +9,15 @@ config FSI
 	---help---
 	  FSI - the FRU Support Interface - is a simple bus for low-level
 	  access to POWER-based hardware.
+
+if FSI
+
+config FSI_MASTER_GPIO
+	tristate "GPIO-based FSI master"
+	depends on FSI && GPIOLIB
+	---help---
+	This option enables a FSI master driver using GPIO lines.
+
+endif
+
 endmenu
diff --git a/drivers/fsi/Makefile b/drivers/fsi/Makefile
index db0e5e7..ed28ac0 100644
--- a/drivers/fsi/Makefile
+++ b/drivers/fsi/Makefile
@@ -1,2 +1,3 @@
 
 obj-$(CONFIG_FSI) += fsi-core.o
+obj-$(CONFIG_FSI_MASTER_GPIO) += fsi-master-gpio.o
diff --git a/drivers/fsi/fsi-master-gpio.c b/drivers/fsi/fsi-master-gpio.c
new file mode 100644
index 0000000..b549d0b
--- /dev/null
+++ b/drivers/fsi/fsi-master-gpio.c
@@ -0,0 +1,530 @@
+/*
+ * FSI GPIO based master driver
+ *
+ * Copyright (C) IBM Corporation 2016
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ *
+ * A FSI master controller, using a simple GPIO bit-banging interface
+ */
+
+#include <linux/platform_device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/fsi.h>
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/crc-fsi.h>
+
+#include "fsi-master.h"
+
+#define	FSI_GPIO_STD_DLY	1	/* Standard pin delay in nS */
+#define	FSI_ECHO_DELAY_CLOCKS	16	/* Number clocks for echo delay */
+#define	FSI_PRE_BREAK_CLOCKS	50	/* Number clocks to prep for break */
+#define	FSI_BREAK_CLOCKS	256	/* Number of clocks to issue break */
+#define	FSI_POST_BREAK_CLOCKS	16000	/* Number clocks to set up cfam */
+#define	FSI_INIT_CLOCKS		5000	/* Clock out any old data */
+#define	FSI_GPIO_STD_DELAY	10	/* Standard GPIO delay in nS */
+					/* todo: adjust down as low as */
+					/* possible or eliminate */
+#define	FSI_GPIO_CMD_DPOLL	0x000000000000002AULL
+#define	FSI_GPIO_CMD_DPOLL_SIZE	9
+#define	FSI_GPIO_DPOLL_CLOCKS	100      /* < 21 will cause slave to hang */
+#define	FSI_GPIO_CMD_DEFAULT	0x2000000000000000ULL
+#define	FSI_GPIO_CMD_WRITE	0
+#define	FSI_GPIO_CMD_READ	0x0400000000000000ULL
+#define	FSI_GPIO_CMD_SLAVE_MASK	0xC000000000000000ULL
+#define	FSI_GPIO_CMD_ADDR_SHIFT	37
+#define	FSI_GPIO_CMD_ADDR_MASK	0x001FFFFF
+#define	FSI_GPIO_CMD_SLV_SHIFT	62
+#define	FSI_GPIO_CMD_SIZE_16	0x0000001000000000ULL
+#define	FSI_GPIO_CMD_SIZE_32	0x0000003000000000ULL
+#define	FSI_GPIO_CMD_DT32_SHIFT	4
+#define	FSI_GPIO_CMD_DT16_SHIFT	20
+#define	FSI_GPIO_CMD_DT8_SHIFT	28
+#define	FSI_GPIO_CMD_DFLT_LEN	28
+#define	FSI_GPIO_CMD_CRC_SHIFT	60
+
+/* Bus errors */
+#define	FSI_GPIO_ERR_BUSY	1	/* Slave stuck in busy state */
+#define	FSI_GPIO_RESP_ERRA	2	/* Any (misc) Error */
+#define	FSI_GPIO_RESP_ERRC	3	/* Slave reports master CRC error */
+#define	FSI_GPIO_MTOE		4	/* Master time out error */
+#define	FSI_GPIO_CRC_INVAL	5	/* Master reports slave CRC error */
+
+/* Normal slave responses */
+#define	FSI_GPIO_RESP_BUSY	1
+#define	FSI_GPIO_RESP_ACK	0
+#define	FSI_GPIO_RESP_ACKD	4
+
+#define	FSI_GPIO_MAX_BUSY	100
+#define	FSI_GPIO_MTOE_COUNT	1000
+#define	FSI_GPIO_DRAIN_BITS	20
+#define	FSI_GPIO_CRC_SIZE	4
+#define	FSI_GPIO_MSG_ID_SIZE		2
+#define	FSI_GPIO_MSG_RESPID_SIZE	2
+#define	FSI_GPIO_PRIME_SLAVE_CLOCKS	100
+
+static DEFINE_SPINLOCK(fsi_gpio_cmd_lock);	/* lock around fsi commands */
+
+struct fsi_master_gpio {
+	struct fsi_master	master;
+	struct gpio_desc	*gpio_clk;
+	struct gpio_desc	*gpio_data;
+	struct gpio_desc	*gpio_trans;	/* Voltage translator */
+	struct gpio_desc	*gpio_enable;	/* FSI enable */
+	struct gpio_desc	*gpio_mux;	/* Mux control */
+};
+
+#define to_fsi_master_gpio(m) container_of(m, struct fsi_master_gpio, master)
+
+struct fsi_gpio_msg {
+	uint64_t	msg;
+	uint8_t		bits;
+};
+
+static void clock_toggle(struct fsi_master_gpio *master, int count)
+{
+	int i;
+
+	for (i = 0; i < count; i++) {
+		ndelay(FSI_GPIO_STD_DLY);
+		gpiod_set_value(master->gpio_clk, 0);
+		ndelay(FSI_GPIO_STD_DLY);
+		gpiod_set_value(master->gpio_clk, 1);
+	}
+}
+
+static int sda_in(struct fsi_master_gpio *master)
+{
+	int in;
+
+	ndelay(FSI_GPIO_STD_DLY);
+	in = gpiod_get_value(master->gpio_data);
+	return in ? 1 : 0;
+}
+
+static void sda_out(struct fsi_master_gpio *master, int value)
+{
+	gpiod_set_value(master->gpio_data, value);
+}
+
+static void set_sda_input(struct fsi_master_gpio *master)
+{
+	gpiod_direction_input(master->gpio_data);
+	if (master->gpio_trans)
+		gpiod_set_value(master->gpio_trans, 0);
+}
+
+static void set_sda_output(struct fsi_master_gpio *master, int value)
+{
+	if (master->gpio_trans)
+		gpiod_set_value(master->gpio_trans, 1);
+	gpiod_direction_output(master->gpio_data, value);
+}
+
+static void serial_in(struct fsi_master_gpio *master, struct fsi_gpio_msg *cmd,
+			uint8_t num_bits)
+{
+	uint8_t bit;
+	uint64_t msg = 0;
+	uint8_t in_bit = 0;
+
+	set_sda_input(master);
+
+	for (bit = 0; bit < num_bits; bit++) {
+		clock_toggle(master, 1);
+		in_bit = sda_in(master);
+		msg <<= 1;
+		msg |= ~in_bit & 0x1;	/* Data is negative active */
+	}
+	cmd->bits = num_bits;
+	cmd->msg = msg;
+}
+
+static void serial_out(struct fsi_master_gpio *master,
+			const struct fsi_gpio_msg *cmd)
+{
+	uint8_t bit;
+	uint64_t msg = ~cmd->msg;	/* Data is negative active */
+	uint64_t sda_mask = 0x1ULL << (cmd->bits - 1);
+	uint64_t last_bit = ~0;
+	int next_bit;
+
+	if (!cmd->bits) {
+		dev_warn(master->master.dev, "trying to output 0 bits\n");
+		return;
+	}
+	set_sda_output(master, 0);
+
+	/* Send the start bit */
+	sda_out(master, 0);
+	clock_toggle(master, 1);
+
+	/* Send the message */
+	for (bit = 0; bit < cmd->bits; bit++) {
+		next_bit = (msg & sda_mask) >> (cmd->bits - 1);
+		if (last_bit ^ next_bit) {
+			sda_out(master, next_bit);
+			last_bit = next_bit;
+		}
+		clock_toggle(master, 1);
+		msg <<= 1;
+	}
+}
+
+/*
+ * Clock out some 0's after every message to ride out line reflections
+ */
+static void echo_delay(struct fsi_master_gpio *master)
+{
+	set_sda_output(master, 1);
+	clock_toggle(master, FSI_ECHO_DELAY_CLOCKS);
+}
+
+/*
+ * Used in bus error cases only.  Clears out any remaining data the slave
+ * is attempting to send
+ */
+static void drain_response(struct fsi_master_gpio *master)
+{
+	struct fsi_gpio_msg msg;
+
+	serial_in(master, &msg, FSI_GPIO_DRAIN_BITS);
+}
+
+/*
+ * Store information on master errors so handler can detect and clean
+ * up the bus
+ */
+static void fsi_master_gpio_error(struct fsi_master_gpio *master, int error)
+{
+
+}
+
+static int poll_for_response(struct fsi_master_gpio *master, uint8_t expected,
+			uint8_t size, void *data)
+{
+	int busy_count = 0, i;
+	struct fsi_gpio_msg response, cmd;
+	int bits_remaining = 0, bit_count, response_id, id;
+	uint64_t resp = 0;
+	uint8_t bits_received = FSI_GPIO_MSG_ID_SIZE +
+				FSI_GPIO_MSG_RESPID_SIZE;
+	uint8_t crc_in;
+
+	do {
+		for (i = 0; i < FSI_GPIO_MTOE_COUNT; i++) {
+			serial_in(master, &response, 1);
+			if (response.msg)
+				break;
+		}
+		if (i >= FSI_GPIO_MTOE_COUNT) {
+			dev_dbg(master->master.dev,
+				"Master time out waiting for response\n");
+			drain_response(master);
+			fsi_master_gpio_error(master, FSI_GPIO_MTOE);
+			return -EIO;
+		}
+
+		/* Response received */
+		bit_count = FSI_GPIO_MSG_ID_SIZE + FSI_GPIO_MSG_RESPID_SIZE;
+		serial_in(master, &response, bit_count);
+
+		response_id = response.msg & 0x3;
+		id = (response.msg >> FSI_GPIO_MSG_RESPID_SIZE) & 0x3;
+		dev_dbg(master->master.dev, "id:%d resp:%d\n", id, response_id);
+
+		resp = response.msg;
+
+		switch (response_id) {
+		case FSI_GPIO_RESP_ACK:
+			if (expected == FSI_GPIO_RESP_ACKD)
+				bits_remaining = 8 * size;
+			break;
+
+		case FSI_GPIO_RESP_BUSY:
+			/*
+			 * Its necessary to clock slave before issuing
+			 * d-poll, not indicated in the hardware protocol
+			 * spec. < 20 clocks causes slave to hang, 21 ok.
+			 */
+			set_sda_output(master, 1);
+			clock_toggle(master, FSI_GPIO_DPOLL_CLOCKS);
+			cmd.msg = FSI_GPIO_CMD_DPOLL;
+			cmd.bits = FSI_GPIO_CMD_DPOLL_SIZE;
+			serial_out(master, &cmd);
+			echo_delay(master);
+			continue;
+
+		case FSI_GPIO_RESP_ERRA:
+		case FSI_GPIO_RESP_ERRC:
+			dev_dbg(master->master.dev, "ERR received: %d\n",
+				(int)response.msg);
+			/*
+			 * todo: Verify crc from slave and in general
+			 * only act on any response if crc is correct
+			 */
+			clock_toggle(master, FSI_GPIO_CRC_SIZE);
+			fsi_master_gpio_error(master, response.msg);
+			return -EIO;
+		}
+
+		/* Read in the data field if applicable */
+		if (bits_remaining) {
+			serial_in(master, &response, bits_remaining);
+			resp <<= bits_remaining;
+			resp |= response.msg;
+			bits_received += bits_remaining;
+			*((uint32_t *)data) = response.msg;
+		}
+
+		crc_in = crc_fsi(0, resp | (0x1ULL << bits_received),
+					bits_received + 1);
+
+		/* Read in the crc and check it */
+		serial_in(master, &response, FSI_GPIO_CRC_SIZE);
+		if (crc_in != response.msg) {
+			dev_dbg(master->master.dev, "ERR response CRC\n");
+			fsi_master_gpio_error(master, FSI_GPIO_CRC_INVAL);
+			return -EIO;
+		}
+		/* Clock the slave enough to be ready for next operation */
+		clock_toggle(master, FSI_GPIO_PRIME_SLAVE_CLOCKS);
+		return 0;
+
+	} while (busy_count++ < FSI_GPIO_MAX_BUSY);
+
+	dev_dbg(master->master.dev, "ERR slave is stuck in busy state\n");
+	fsi_master_gpio_error(master, FSI_GPIO_ERR_BUSY);
+
+	return -EIO;
+}
+
+static void build_abs_ar_command(struct fsi_gpio_msg *cmd, uint64_t mode,
+		uint8_t slave, uint32_t addr, size_t size,
+		const void *data)
+{
+	uint8_t crc;
+
+	cmd->bits = FSI_GPIO_CMD_DFLT_LEN;
+	cmd->msg = FSI_GPIO_CMD_DEFAULT;
+	cmd->msg |= mode;
+	cmd->msg &= ~FSI_GPIO_CMD_SLAVE_MASK;
+	cmd->msg |= (((uint64_t)slave) << FSI_GPIO_CMD_SLV_SHIFT);
+	addr &= FSI_GPIO_CMD_ADDR_MASK;
+	cmd->msg |= (((uint64_t)addr) << FSI_GPIO_CMD_ADDR_SHIFT);
+	if (size == sizeof(uint8_t)) {
+		if (data) {
+			uint8_t cmd_data = *((uint8_t *)data);
+
+			cmd->msg |=
+				((uint64_t)cmd_data) << FSI_GPIO_CMD_DT8_SHIFT;
+		}
+	} else if (size == sizeof(uint16_t)) {
+		cmd->msg |= FSI_GPIO_CMD_SIZE_16;
+		if (data) {
+			uint16_t cmd_data;
+
+			memcpy(&cmd_data, data, size);
+			cmd->msg |=
+				((uint64_t)cmd_data) << FSI_GPIO_CMD_DT16_SHIFT;
+		}
+	} else {
+		cmd->msg |= FSI_GPIO_CMD_SIZE_32;
+		if (data) {
+			uint32_t cmd_data;
+
+			memcpy(&cmd_data, data, size);
+			cmd->msg |=
+				((uint64_t)cmd_data) << FSI_GPIO_CMD_DT32_SHIFT;
+		}
+	}
+
+	if (mode == FSI_GPIO_CMD_WRITE)
+		cmd->bits += (8 * size);
+
+	/* Include start bit */
+	crc = crc_fsi(0,
+			(cmd->msg >> (64 - cmd->bits)) | (0x1ULL << cmd->bits),
+			cmd->bits + 1);
+	cmd->msg |= ((uint64_t)crc) << (FSI_GPIO_CMD_CRC_SHIFT - cmd->bits);
+	cmd->bits += FSI_GPIO_CRC_SIZE;
+
+	/* Right align message */
+	cmd->msg >>= (64 - cmd->bits);
+}
+
+static int fsi_master_gpio_read(struct fsi_master *_master, int link,
+		uint8_t slave, uint32_t addr, void *val, size_t size)
+{
+	struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+	struct fsi_gpio_msg cmd;
+	int rc;
+	unsigned long flags;
+
+	if (link != 0)
+		return -ENODEV;
+
+	build_abs_ar_command(&cmd, FSI_GPIO_CMD_READ, slave, addr, size, NULL);
+
+	spin_lock_irqsave(&fsi_gpio_cmd_lock, flags);
+	serial_out(master, &cmd);
+	echo_delay(master);
+	rc = poll_for_response(master, FSI_GPIO_RESP_ACKD, size, val);
+	spin_unlock_irqrestore(&fsi_gpio_cmd_lock, flags);
+
+	return rc;
+}
+
+static int fsi_master_gpio_write(struct fsi_master *_master, int link,
+		uint8_t slave, uint32_t addr, const void *val, size_t size)
+{
+	struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+	struct fsi_gpio_msg cmd;
+	int rc;
+	unsigned long flags;
+
+	if (link != 0)
+		return -ENODEV;
+
+	build_abs_ar_command(&cmd, FSI_GPIO_CMD_WRITE, slave, addr, size, val);
+
+	spin_lock_irqsave(&fsi_gpio_cmd_lock, flags);
+	serial_out(master, &cmd);
+	echo_delay(master);
+	rc = poll_for_response(master, FSI_GPIO_RESP_ACK, size, NULL);
+	spin_unlock_irqrestore(&fsi_gpio_cmd_lock, flags);
+
+	return rc;
+}
+
+/*
+ * Issue a break command on link
+ */
+static int fsi_master_gpio_break(struct fsi_master *_master, int link)
+{
+	struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+
+	if (link != 0)
+		return -ENODEV;
+
+	set_sda_output(master, 1);
+	clock_toggle(master, FSI_PRE_BREAK_CLOCKS);
+	sda_out(master, 0);
+	clock_toggle(master, FSI_BREAK_CLOCKS);
+	echo_delay(master);
+	sda_out(master, 1);
+	clock_toggle(master, FSI_POST_BREAK_CLOCKS);
+
+	/* Wait for logic reset to take effect */
+	udelay(200);
+
+	return 0;
+}
+
+static int fsi_master_gpio_link_enable(struct fsi_master *_master, int link)
+{
+	struct fsi_master_gpio *master = to_fsi_master_gpio(_master);
+
+	if (link != 0)
+		return -ENODEV;
+	if (master->gpio_enable)
+		gpiod_set_value(master->gpio_enable, 1);
+
+	return 0;
+}
+
+static int fsi_master_gpio_probe(struct platform_device *pdev)
+{
+	struct fsi_master_gpio *master;
+
+	master = devm_kzalloc(&pdev->dev, sizeof(*master), GFP_KERNEL);
+	if (!master)
+		return -ENOMEM;
+
+	master->master.dev = &pdev->dev;
+
+	master->gpio_clk = devm_gpiod_get(&pdev->dev, "clock", GPIOD_OUT_HIGH);
+	if (IS_ERR(master->gpio_clk)) {
+		dev_dbg(&pdev->dev, "probe: failed to get clock pin\n");
+		return PTR_ERR(master->gpio_clk);
+	}
+
+	master->gpio_data = devm_gpiod_get(&pdev->dev, "data", GPIOD_OUT_HIGH);
+	if (IS_ERR(master->gpio_data)) {
+		dev_dbg(&pdev->dev, "probe: failed to get data pin\n");
+		return PTR_ERR(master->gpio_data);
+	}
+
+	/* Optional pins */
+
+	master->gpio_trans = devm_gpiod_get_optional(&pdev->dev, "trans",
+							GPIOD_OUT_HIGH);
+	if (IS_ERR(master->gpio_trans))
+		dev_dbg(&pdev->dev, "probe: failed to get trans pin\n");
+
+	master->gpio_enable = devm_gpiod_get_optional(&pdev->dev, "enable",
+							GPIOD_OUT_HIGH);
+	if (IS_ERR(master->gpio_enable))
+		dev_dbg(&pdev->dev, "probe: failed to get enable pin\n");
+
+	master->gpio_mux = devm_gpiod_get_optional(&pdev->dev, "mux",
+							GPIOD_OUT_HIGH);
+	if (IS_ERR(master->gpio_mux))
+		dev_dbg(&pdev->dev, "probe: failed to get mux pin\n");
+
+	/* todo: evaluate if clocks can be reduced */
+	clock_toggle(master, FSI_INIT_CLOCKS);
+
+	master->master.n_links = 1;
+	master->master.read = fsi_master_gpio_read;
+	master->master.write = fsi_master_gpio_write;
+	master->master.send_break = fsi_master_gpio_break;
+	master->master.link_enable = fsi_master_gpio_link_enable;
+	return fsi_master_register(&master->master);
+}
+
+static int fsi_master_gpio_remove(struct platform_device *pdev)
+{
+	struct fsi_master_gpio *master = platform_get_drvdata(pdev);
+
+	devm_gpiod_put(&pdev->dev, master->gpio_clk);
+	devm_gpiod_put(&pdev->dev, master->gpio_data);
+	if (master->gpio_trans)
+		devm_gpiod_put(&pdev->dev, master->gpio_trans);
+	if (master->gpio_enable)
+		devm_gpiod_put(&pdev->dev, master->gpio_enable);
+	if (master->gpio_mux)
+		devm_gpiod_put(&pdev->dev, master->gpio_mux);
+	fsi_master_unregister(&master->master);
+
+	return 0;
+}
+
+static const struct of_device_id fsi_master_gpio_match[] = {
+	{ .compatible = "ibm,fsi-master-gpio" },
+	{ },
+};
+
+static struct platform_driver fsi_master_gpio_driver = {
+	.driver = {
+		.name		= "fsi-master-gpio",
+		.of_match_table	= fsi_master_gpio_match,
+	},
+	.probe	= fsi_master_gpio_probe,
+	.remove = fsi_master_gpio_remove,
+};
+
+module_platform_driver(fsi_master_gpio_driver);
+MODULE_LICENSE("GPL");
-- 
1.8.2.2