[PATCH v5] usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
From: Richard Leitner
Date: Fri Feb 10 2017 - 03:30:58 EST
This patch adds a driver for configuration of the Microchip USB251xB/xBi
USB 2.0 hub controller series with USB 2.0 upstream connectivity, SMBus
configuration interface and two to four USB 2.0 downstream ports.
Furthermore add myself as a maintainer for this driver.
The datasheet can be found at the manufacturers website, see [1]. All
device-tree exposed configuration features have been tested on a i.MX6
platform with a USB2512B hub.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/00001692C.pdf
Signed-off-by: Richard Leitner <richard.leitner@xxxxxxxxxxx>
---
CHANGES v5:
- Put includes in alphabetical order
- Fix some indentations
- Replace {set,clr}_bit_in_byte with BIT() macros
- Fix multiline comments
- Use of_property_read_u32() instead of of_get_property() where possible
- Use min_t() instead of by-hand implemented if's
- Use strlcpy and ternary operator instead of strncpy in if/else
- Remove useless & improve some other outputs
- Omit i2c remove function
- Use module_i2c_driver() instead of module_{init,exit}()
CHANGES v4:
- use utf8s_to_utf16s() instead of ascii2utf16le()
- remove ascii2utf16le() in lib/string.c again
- remove changes in drivers/usb/core/hcd.c again
(I will post a separate patch for using utf8s_to_utf16s()
in there too)
CHANGES v3:
- move ascii2utf16le() to lib/string.c and also use it also for
ascii2desc in drivers/usb/core/hcd.c
- remove platform data support from usb251xb driver
CHANGES v2:
- fix max-{b,s}p-current property name
- add descriptor string handling from platform_data
- fix non-dt handling
---
Documentation/devicetree/bindings/usb/usb251xb.txt | 83 +++
MAINTAINERS | 8 +
drivers/usb/misc/Kconfig | 9 +
drivers/usb/misc/Makefile | 1 +
drivers/usb/misc/usb251xb.c | 605 +++++++++++++++++++++
5 files changed, 706 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/usb251xb.txt
create mode 100644 drivers/usb/misc/usb251xb.c
diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt
new file mode 100644
index 0000000..0c065f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/usb251xb.txt
@@ -0,0 +1,83 @@
+Microchip USB 2.0 Hi-Speed Hub Controller
+
+The device node for the configuration of a Microchip USB251xB/xBi USB 2.0
+Hi-Speed Controller.
+
+Required properties :
+ - compatible : Should be "microchip,usb251xb" or one of the specific types:
+ "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b",
+ "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi"
+ - hub-reset-gpios : Should specify the gpio for hub reset
+
+Optional properties :
+ - reg : I2C address on the selected bus (default is <0x2C>)
+ - skip-config : Skip Hub configuration, but only send the USB-Attach command
+ - vendor-id : USB Vendor ID of the hub (16 bit, default is 0x0424)
+ - product-id : USB Product ID of the hub (16 bit, default depends on type)
+ - device-id : USB Device ID of the hub (16 bit, default is 0x0bb3)
+ - language-id : USB Language ID (16 bit, default is 0x0000)
+ - manufacturer : USB Manufacturer string (max 31 characters long)
+ - product : USB Product string (max 31 characters long)
+ - serial : USB Serial string (max 31 characters long)
+ - {bus,self}-powered : selects between self- and bus-powered operation (default
+ is self-powered)
+ - disable-hi-speed : disable USB Hi-Speed support
+ - {multi,single}-tt : selects between multi- and single-transaction-translator
+ (default is multi-tt)
+ - disable-eop : disable End of Packet generation in full-speed mode
+ - {ganged,individual}-sensing : select over-current sense type in self-powered
+ mode (default is individual)
+ - {ganged,individual}-port-switching : select port power switching mode
+ (default is individual)
+ - dynamic-power-switching : enable auto-switching from self- to bus-powered
+ operation if the local power source is removed or unavailable
+ - oc-delay-{100us,4ms,8ms,16ms} : set over current timer delay (default is 8ms)
+ - compound-device : indicated the hub is part of a compound device
+ - port-mapping-mode : enable port mapping mode
+ - string-support : enable string descriptor support (required for manufacturer,
+ product and serial string configuration)
+ - non-removable-ports : Should specify the ports which have a non-removable
+ device connected.
+ - sp-disabled-ports : Specifies the ports which will be self-power disabled
+ - bp-disabled-ports : Specifies the ports which will be bus-power disabled
+ - max-sp-power : Specifies the maximum current the hub consumes from an
+ upstream port when operating as self-powered hub including the power
+ consumption of a permanently attached peripheral if the hub is
+ configured as a compound device. The value is given in mA in a 0 - 500
+ range (default is 2).
+ - max-bp-power : Specifies the maximum current the hub consumes from an
+ upstream port when operating as bus-powered hub including the power
+ consumption of a permanently attached peripheral if the hub is
+ configured as a compound device. The value is given in mA in a 0 - 500
+ range (default is 100).
+ - max-sp-current : Specifies the maximum current the hub consumes from an
+ upstream port when operating as self-powered hub EXCLUDING the power
+ consumption of a permanently attached peripheral if the hub is
+ configured as a compound device. The value is given in mA in a 0 - 500
+ range (default is 2).
+ - max-bp-current : Specifies the maximum current the hub consumes from an
+ upstream port when operating as bus-powered hub EXCLUDING the power
+ consumption of a permanently attached peripheral if the hub is
+ configured as a compound device. The value is given in mA in a 0 - 500
+ range (default is 100).
+ - power-on-time : Specifies the time it takes from the time the host initiates
+ the power-on sequence to a port until the port has adequate power. The
+ value is given in ms in a 0 - 510 range (default is 100ms).
+
+Examples:
+ usb2512b@2c {
+ compatible = "microchip,usb2512b";
+ hub-reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ };
+
+ usb2514b@2c {
+ compatible = "microchip,usb2514b";
+ reg = <0x2c>;
+ reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ vendor-id = /bits/ 16 <0x0000>;
+ product-id = /bits/ 16 <0x0000>;
+ string-support;
+ manufacturer = "Foo";
+ product = "Foo-Bar";
+ serial = "1234567890A";
+ };
diff --git a/MAINTAINERS b/MAINTAINERS
index 107c10e..ecc139b 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -8201,6 +8201,14 @@ F: drivers/media/platform/atmel/atmel-isc.c
F: drivers/media/platform/atmel/atmel-isc-regs.h
F: devicetree/bindings/media/atmel-isc.txt
+MICROCHIP USB251XB DRIVER
+M: Richard Leitner <richard.leitner@xxxxxxxxxxx>
+L: linux-usb@xxxxxxxxxxxxxxx
+S: Maintained
+F: drivers/usb/misc/usb251xb.c
+F: include/linux/platform_data/usb251xb.h
+F: Documentation/devicetree/bindings/usb/usb251xb.txt
+
MICROSOFT SURFACE PRO 3 BUTTON DRIVER
M: Chen Yu <yu.c.chen@xxxxxxxxx>
L: platform-driver-x86@xxxxxxxxxxxxxxx
diff --git a/drivers/usb/misc/Kconfig b/drivers/usb/misc/Kconfig
index 47b3577..1d1d70d 100644
--- a/drivers/usb/misc/Kconfig
+++ b/drivers/usb/misc/Kconfig
@@ -233,6 +233,15 @@ config USB_EZUSB_FX2
Say Y here if you need EZUSB device support.
(Cypress FX/FX2/FX2LP microcontrollers)
+config USB_HUB_USB251XB
+ tristate "USB251XB Hub Controller Configuration Driver"
+ depends on I2C
+ help
+ This option enables support for configuration via SMBus of the
+ Microchip USB251xB/xBi USB 2.0 Hub Controller series.
+ Configuration parameters may be set in devicetree or platform data.
+ Say Y or M here if you need to configure such a device via SMBus.
+
config USB_HSIC_USB3503
tristate "USB3503 HSIC to USB20 Driver"
depends on I2C
diff --git a/drivers/usb/misc/Makefile b/drivers/usb/misc/Makefile
index 3d19927..f6ac6c9 100644
--- a/drivers/usb/misc/Makefile
+++ b/drivers/usb/misc/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_USB_TRANCEVIBRATOR) += trancevibrator.o
obj-$(CONFIG_USB_USS720) += uss720.o
obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o
obj-$(CONFIG_USB_YUREX) += yurex.o
+obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o
obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o
obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o
diff --git a/drivers/usb/misc/usb251xb.c b/drivers/usb/misc/usb251xb.c
new file mode 100644
index 0000000..4e18600
--- /dev/null
+++ b/drivers/usb/misc/usb251xb.c
@@ -0,0 +1,605 @@
+/*
+ * Driver for Microchip USB251xB USB 2.0 Hi-Speed Hub Controller
+ * Configuration via SMBus.
+ *
+ * Copyright (c) 2017 SKIDATA AG
+ *
+ * This work is based on the USB3503 driver by Dongjin Kim and
+ * a not-accepted patch by Fabien Lahoudere, see:
+ * https://patchwork.kernel.org/patch/9257715/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/nls.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/slab.h>
+
+/* Internal Register Set Addresses & Default Values acc. to DS00001692C */
+#define USB251XB_ADDR_VENDOR_ID_LSB 0x00
+#define USB251XB_ADDR_VENDOR_ID_MSB 0x01
+#define USB251XB_DEF_VENDOR_ID 0x0424
+
+#define USB251XB_ADDR_PRODUCT_ID_LSB 0x02
+#define USB251XB_ADDR_PRODUCT_ID_MSB 0x03
+#define USB251XB_DEF_PRODUCT_ID_12 0x2512 /* USB2512B/12Bi */
+#define USB251XB_DEF_PRODUCT_ID_13 0x2513 /* USB2513B/13Bi */
+#define USB251XB_DEF_PRODUCT_ID_14 0x2514 /* USB2514B/14Bi */
+
+#define USB251XB_ADDR_DEVICE_ID_LSB 0x04
+#define USB251XB_ADDR_DEVICE_ID_MSB 0x05
+#define USB251XB_DEF_DEVICE_ID 0x0BB3
+
+#define USB251XB_ADDR_CONFIG_DATA_1 0x06
+#define USB251XB_DEF_CONFIG_DATA_1 0x9B
+#define USB251XB_ADDR_CONFIG_DATA_2 0x07
+#define USB251XB_DEF_CONFIG_DATA_2 0x20
+#define USB251XB_ADDR_CONFIG_DATA_3 0x08
+#define USB251XB_DEF_CONFIG_DATA_3 0x02
+
+#define USB251XB_ADDR_NON_REMOVABLE_DEVICES 0x09
+#define USB251XB_DEF_NON_REMOVABLE_DEVICES 0x00
+
+#define USB251XB_ADDR_PORT_DISABLE_SELF 0x0A
+#define USB251XB_DEF_PORT_DISABLE_SELF 0x00
+#define USB251XB_ADDR_PORT_DISABLE_BUS 0x0B
+#define USB251XB_DEF_PORT_DISABLE_BUS 0x00
+
+#define USB251XB_ADDR_MAX_POWER_SELF 0x0C
+#define USB251XB_DEF_MAX_POWER_SELF 0x01
+#define USB251XB_ADDR_MAX_POWER_BUS 0x0D
+#define USB251XB_DEF_MAX_POWER_BUS 0x32
+
+#define USB251XB_ADDR_MAX_CURRENT_SELF 0x0E
+#define USB251XB_DEF_MAX_CURRENT_SELF 0x01
+#define USB251XB_ADDR_MAX_CURRENT_BUS 0x0F
+#define USB251XB_DEF_MAX_CURRENT_BUS 0x32
+
+#define USB251XB_ADDR_POWER_ON_TIME 0x10
+#define USB251XB_DEF_POWER_ON_TIME 0x32
+
+#define USB251XB_ADDR_LANGUAGE_ID_HIGH 0x11
+#define USB251XB_ADDR_LANGUAGE_ID_LOW 0x12
+#define USB251XB_DEF_LANGUAGE_ID 0x0000
+
+#define USB251XB_STRING_BUFSIZE 62
+#define USB251XB_ADDR_MANUFACTURER_STRING_LEN 0x13
+#define USB251XB_ADDR_MANUFACTURER_STRING 0x16
+#define USB251XB_DEF_MANUFACTURER_STRING "Microchip"
+
+#define USB251XB_ADDR_PRODUCT_STRING_LEN 0x14
+#define USB251XB_ADDR_PRODUCT_STRING 0x54
+#define USB251XB_DEF_PRODUCT_STRING "USB251xB/xBi"
+
+#define USB251XB_ADDR_SERIAL_STRING_LEN 0x15
+#define USB251XB_ADDR_SERIAL_STRING 0x92
+#define USB251XB_DEF_SERIAL_STRING ""
+
+#define USB251XB_ADDR_BATTERY_CHARGING_ENABLE 0xD0
+#define USB251XB_DEF_BATTERY_CHARGING_ENABLE 0x00
+
+#define USB251XB_ADDR_BOOST_UP 0xF6
+#define USB251XB_DEF_BOOST_UP 0x00
+#define USB251XB_ADDR_BOOST_X 0xF8
+#define USB251XB_DEF_BOOST_X 0x00
+
+#define USB251XB_ADDR_PORT_SWAP 0xFA
+#define USB251XB_DEF_PORT_SWAP 0x00
+
+#define USB251XB_ADDR_PORT_MAP_12 0xFB
+#define USB251XB_DEF_PORT_MAP_12 0x00
+#define USB251XB_ADDR_PORT_MAP_34 0xFC
+#define USB251XB_DEF_PORT_MAP_34 0x00 /* USB2513B/i & USB2514B/i only */
+
+#define USB251XB_ADDR_STATUS_COMMAND 0xFF
+#define USB251XB_STATUS_COMMAND_SMBUS_DOWN 0x04
+#define USB251XB_STATUS_COMMAND_RESET 0x02
+#define USB251XB_STATUS_COMMAND_ATTACH 0x01
+
+#define USB251XB_I2C_REG_SZ 0x100
+#define USB251XB_I2C_WRITE_SZ 0x10
+
+#define DRIVER_NAME "usb251xb"
+#define DRIVER_DESC "Microchip USB 2.0 Hi-Speed Hub Controller"
+#define DRIVER_VERSION "1.0"
+
+struct usb251xb {
+ struct device *dev;
+ struct i2c_client *i2c;
+ u8 skip_config;
+ int gpio_reset;
+ u16 vendor_id;
+ u16 product_id;
+ u16 device_id;
+ u8 conf_data1;
+ u8 conf_data2;
+ u8 conf_data3;
+ u8 non_rem_dev;
+ u8 port_disable_sp;
+ u8 port_disable_bp;
+ u8 max_power_sp;
+ u8 max_power_bp;
+ u8 max_current_sp;
+ u8 max_current_bp;
+ u8 power_on_time;
+ u16 lang_id;
+ u8 manufacturer_len;
+ u8 product_len;
+ u8 serial_len;
+ char manufacturer[USB251XB_STRING_BUFSIZE];
+ char product[USB251XB_STRING_BUFSIZE];
+ char serial[USB251XB_STRING_BUFSIZE];
+ u8 bat_charge_en;
+ u8 boost_up;
+ u8 boost_x;
+ u8 port_swap;
+ u8 port_map12;
+ u8 port_map34;
+ u8 status;
+};
+
+struct usb251xb_data {
+ u16 product_id;
+ char product_str[USB251XB_STRING_BUFSIZE / 2]; /* ASCII string */
+};
+
+static const struct usb251xb_data usb2512b_data = {
+ .product_id = 0x2512,
+ .product_str = "USB2512B",
+};
+
+static const struct usb251xb_data usb2512bi_data = {
+ .product_id = 0x2512,
+ .product_str = "USB2512Bi",
+};
+
+static const struct usb251xb_data usb2513b_data = {
+ .product_id = 0x2513,
+ .product_str = "USB2513B",
+};
+
+static const struct usb251xb_data usb2513bi_data = {
+ .product_id = 0x2513,
+ .product_str = "USB2513Bi",
+};
+
+static const struct usb251xb_data usb2514b_data = {
+ .product_id = 0x2514,
+ .product_str = "USB2514B",
+};
+
+static const struct usb251xb_data usb2514bi_data = {
+ .product_id = 0x2514,
+ .product_str = "USB2514Bi",
+};
+
+static void usb251xb_reset(struct usb251xb *hub, int state)
+{
+ if (!gpio_is_valid(hub->gpio_reset))
+ return;
+
+ gpio_set_value_cansleep(hub->gpio_reset, state);
+
+ /* wait for hub recovery/stabilization */
+ if (state)
+ usleep_range(500, 750); /* >=500us at power on */
+ else
+ usleep_range(1, 10); /* >=1us at power down */
+}
+
+static int usb251xb_connect(struct usb251xb *hub)
+{
+ struct device *dev = hub->dev;
+ int err, i;
+ char i2c_wb[USB251XB_I2C_REG_SZ];
+
+ memset(i2c_wb, 0, USB251XB_I2C_REG_SZ);
+
+ if (hub->skip_config) {
+ dev_info(dev, "Skip hub configuration, only attach.\n");
+ i2c_wb[0] = 0x01;
+ i2c_wb[1] = USB251XB_STATUS_COMMAND_ATTACH;
+
+ usb251xb_reset(hub, 1);
+
+ err = i2c_smbus_write_i2c_block_data(hub->i2c,
+ USB251XB_ADDR_STATUS_COMMAND, 2, i2c_wb);
+ if (err) {
+ dev_err(dev, "attaching hub failed: %d\n", err);
+ return err;
+ }
+ return 0;
+ }
+
+ i2c_wb[USB251XB_ADDR_VENDOR_ID_MSB] = (hub->vendor_id >> 8) & 0xFF;
+ i2c_wb[USB251XB_ADDR_VENDOR_ID_LSB] = hub->vendor_id & 0xFF;
+ i2c_wb[USB251XB_ADDR_PRODUCT_ID_MSB] = (hub->product_id >> 8) & 0xFF;
+ i2c_wb[USB251XB_ADDR_PRODUCT_ID_LSB] = hub->product_id & 0xFF;
+ i2c_wb[USB251XB_ADDR_DEVICE_ID_MSB] = (hub->device_id >> 8) & 0xFF;
+ i2c_wb[USB251XB_ADDR_DEVICE_ID_LSB] = hub->device_id & 0xFF;
+ i2c_wb[USB251XB_ADDR_CONFIG_DATA_1] = hub->conf_data1;
+ i2c_wb[USB251XB_ADDR_CONFIG_DATA_2] = hub->conf_data2;
+ i2c_wb[USB251XB_ADDR_CONFIG_DATA_3] = hub->conf_data3;
+ i2c_wb[USB251XB_ADDR_NON_REMOVABLE_DEVICES] = hub->non_rem_dev;
+ i2c_wb[USB251XB_ADDR_PORT_DISABLE_SELF] = hub->port_disable_sp;
+ i2c_wb[USB251XB_ADDR_PORT_DISABLE_BUS] = hub->port_disable_bp;
+ i2c_wb[USB251XB_ADDR_MAX_POWER_SELF] = hub->max_power_sp;
+ i2c_wb[USB251XB_ADDR_MAX_POWER_BUS] = hub->max_power_bp;
+ i2c_wb[USB251XB_ADDR_MAX_CURRENT_SELF] = hub->max_current_sp;
+ i2c_wb[USB251XB_ADDR_MAX_CURRENT_BUS] = hub->max_current_bp;
+ i2c_wb[USB251XB_ADDR_POWER_ON_TIME] = hub->power_on_time;
+ i2c_wb[USB251XB_ADDR_LANGUAGE_ID_HIGH] = (hub->lang_id >> 8) & 0xFF;
+ i2c_wb[USB251XB_ADDR_LANGUAGE_ID_LOW] = hub->lang_id & 0xFF;
+ i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING_LEN] = hub->manufacturer_len;
+ i2c_wb[USB251XB_ADDR_PRODUCT_STRING_LEN] = hub->product_len;
+ i2c_wb[USB251XB_ADDR_SERIAL_STRING_LEN] = hub->serial_len;
+ memcpy(&i2c_wb[USB251XB_ADDR_MANUFACTURER_STRING], hub->manufacturer,
+ USB251XB_STRING_BUFSIZE);
+ memcpy(&i2c_wb[USB251XB_ADDR_SERIAL_STRING], hub->serial,
+ USB251XB_STRING_BUFSIZE);
+ memcpy(&i2c_wb[USB251XB_ADDR_PRODUCT_STRING], hub->product,
+ USB251XB_STRING_BUFSIZE);
+ i2c_wb[USB251XB_ADDR_BATTERY_CHARGING_ENABLE] = hub->bat_charge_en;
+ i2c_wb[USB251XB_ADDR_BOOST_UP] = hub->boost_up;
+ i2c_wb[USB251XB_ADDR_BOOST_X] = hub->boost_x;
+ i2c_wb[USB251XB_ADDR_PORT_SWAP] = hub->port_swap;
+ i2c_wb[USB251XB_ADDR_PORT_MAP_12] = hub->port_map12;
+ i2c_wb[USB251XB_ADDR_PORT_MAP_34] = hub->port_map34;
+ i2c_wb[USB251XB_ADDR_STATUS_COMMAND] = USB251XB_STATUS_COMMAND_ATTACH;
+
+ usb251xb_reset(hub, 1);
+
+ /* write registers */
+ for (i = 0; i < (USB251XB_I2C_REG_SZ / USB251XB_I2C_WRITE_SZ); i++) {
+ int offset = i * USB251XB_I2C_WRITE_SZ;
+ char wbuf[USB251XB_I2C_WRITE_SZ + 1];
+
+ /* The first data byte transferred tells the hub how many data
+ * bytes will follow (byte count).
+ */
+ wbuf[0] = USB251XB_I2C_WRITE_SZ;
+ memcpy(&wbuf[1], &i2c_wb[offset], USB251XB_I2C_WRITE_SZ);
+
+ dev_dbg(dev, "writing %d byte block %d to 0x%02X\n",
+ USB251XB_I2C_WRITE_SZ, i, offset);
+
+ err = i2c_smbus_write_i2c_block_data(hub->i2c, offset,
+ USB251XB_I2C_WRITE_SZ + 1,
+ wbuf);
+ if (err)
+ goto out_err;
+ }
+
+ dev_info(dev, "Hub configuration was successful.\n");
+ return 0;
+
+out_err:
+ dev_err(dev, "configuring block %d failed: %d\n", i, err);
+ return err;
+}
+
+#ifdef CONFIG_OF
+static int usb251xb_get_ofdata(struct usb251xb *hub,
+ struct usb251xb_data *data)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+ int len, err, i;
+ u32 *property_u32 = NULL;
+ const u32 *cproperty_u32;
+ const char *cproperty_char;
+ char str[USB251XB_STRING_BUFSIZE / 2];
+
+ if (!np) {
+ dev_err(dev, "failed to get ofdata\n");
+ return -ENODEV;
+ }
+
+ if (of_get_property(np, "skip-config", NULL))
+ hub->skip_config = 1;
+ else
+ hub->skip_config = 0;
+
+ hub->gpio_reset = of_get_named_gpio(np, "reset-gpios", 0);
+ if (hub->gpio_reset == -EPROBE_DEFER)
+ return -EPROBE_DEFER;
+ if (gpio_is_valid(hub->gpio_reset)) {
+ err = devm_gpio_request_one(dev, hub->gpio_reset,
+ GPIOF_OUT_INIT_LOW,
+ "usb251xb reset");
+ if (err) {
+ dev_err(dev,
+ "unable to request GPIO %d as reset pin (%d)\n",
+ hub->gpio_reset, err);
+ return err;
+ }
+ }
+
+ if (of_property_read_u16_array(np, "vendor-id", &hub->vendor_id, 1))
+ hub->vendor_id = USB251XB_DEF_VENDOR_ID;
+
+ if (of_property_read_u16_array(np, "product-id",
+ &hub->product_id, 1))
+ hub->product_id = data->product_id;
+
+ if (of_property_read_u16_array(np, "device-id", &hub->device_id, 1))
+ hub->device_id = USB251XB_DEF_DEVICE_ID;
+
+ hub->conf_data1 = USB251XB_DEF_CONFIG_DATA_1;
+ if (of_get_property(np, "self-powered", NULL)) {
+ hub->conf_data1 |= BIT(7);
+
+ /* Configure Over-Current sens when self-powered */
+ hub->conf_data1 &= ~BIT(2);
+ if (of_get_property(np, "ganged-sensing", NULL))
+ hub->conf_data1 &= ~BIT(1);
+ else if (of_get_property(np, "individual-sensing", NULL))
+ hub->conf_data1 |= BIT(1);
+ } else if (of_get_property(np, "bus-powered", NULL)) {
+ hub->conf_data1 &= ~BIT(7);
+
+ /* Disable Over-Current sense when bus-powered */
+ hub->conf_data1 |= BIT(2);
+ }
+
+ if (of_get_property(np, "disable-hi-speed", NULL))
+ hub->conf_data1 |= BIT(5);
+
+ if (of_get_property(np, "multi-tt", NULL))
+ hub->conf_data1 |= BIT(4);
+ else if (of_get_property(np, "single-tt", NULL))
+ hub->conf_data1 &= ~BIT(4);
+
+ if (of_get_property(np, "disable-eop", NULL))
+ hub->conf_data1 |= BIT(3);
+
+ if (of_get_property(np, "individual-port-switching", NULL))
+ hub->conf_data1 |= BIT(0);
+ else if (of_get_property(np, "ganged-port-switching", NULL))
+ hub->conf_data1 &= ~BIT(0);
+
+ hub->conf_data2 = USB251XB_DEF_CONFIG_DATA_2;
+ if (of_get_property(np, "dynamic-power-switching", NULL))
+ hub->conf_data2 |= BIT(7);
+
+ if (of_get_property(np, "oc-delay-100us", NULL)) {
+ hub->conf_data2 &= ~BIT(5);
+ hub->conf_data2 &= ~BIT(4);
+ } else if (of_get_property(np, "oc-delay-4ms", NULL)) {
+ hub->conf_data2 &= ~BIT(5);
+ hub->conf_data2 |= BIT(4);
+ } else if (of_get_property(np, "oc-delay-8ms", NULL)) {
+ hub->conf_data2 |= BIT(5);
+ hub->conf_data2 &= ~BIT(4);
+ } else if (of_get_property(np, "oc-delay-16ms", NULL)) {
+ hub->conf_data2 |= BIT(5);
+ hub->conf_data2 |= BIT(4);
+ }
+
+ if (of_get_property(np, "compound-device", NULL))
+ hub->conf_data2 |= BIT(3);
+
+ hub->conf_data3 = USB251XB_DEF_CONFIG_DATA_3;
+ if (of_get_property(np, "port-mapping-mode", NULL))
+ hub->conf_data3 |= BIT(3);
+
+ if (of_get_property(np, "string-support", NULL))
+ hub->conf_data3 |= BIT(0);
+
+ hub->non_rem_dev = USB251XB_DEF_NON_REMOVABLE_DEVICES;
+ cproperty_u32 = of_get_property(np, "non-removable-ports", &len);
+ if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+ for (i = 0; i < len / sizeof(u32); i++) {
+ u32 port = be32_to_cpu(cproperty_u32[i]);
+
+ if ((port >= 1) && (port <= 4))
+ hub->non_rem_dev |= BIT(port);
+ }
+ }
+
+ hub->port_disable_sp = USB251XB_DEF_PORT_DISABLE_SELF;
+ cproperty_u32 = of_get_property(np, "sp-disabled-ports", &len);
+ if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+ for (i = 0; i < len / sizeof(u32); i++) {
+ u32 port = be32_to_cpu(cproperty_u32[i]);
+
+ if ((port >= 1) && (port <= 4))
+ hub->port_disable_sp |= BIT(port);
+ }
+ }
+
+ hub->port_disable_bp = USB251XB_DEF_PORT_DISABLE_BUS;
+ cproperty_u32 = of_get_property(np, "bp-disabled-ports", &len);
+ if (cproperty_u32 && (len / sizeof(u32)) > 0) {
+ for (i = 0; i < len / sizeof(u32); i++) {
+ u32 port = be32_to_cpu(cproperty_u32[i]);
+
+ if ((port >= 1) && (port <= 4))
+ hub->port_disable_bp |= BIT(port);
+ }
+ }
+
+ hub->max_power_sp = USB251XB_DEF_MAX_POWER_SELF;
+ if (!of_property_read_u32(np, "max-sp-power", property_u32))
+ hub->max_power_sp = min_t(u8, be32_to_cpu(*property_u32) / 2,
+ 250);
+
+ hub->max_power_bp = USB251XB_DEF_MAX_POWER_BUS;
+ if (!of_property_read_u32(np, "max-bp-power", property_u32))
+ hub->max_power_bp = min_t(u8, be32_to_cpu(*property_u32) / 2,
+ 250);
+
+ hub->max_current_sp = USB251XB_DEF_MAX_CURRENT_SELF;
+ if (!of_property_read_u32(np, "max-sp-current", property_u32))
+ hub->max_current_sp = min_t(u8, be32_to_cpu(*property_u32) / 2,
+ 250);
+
+ hub->max_current_bp = USB251XB_DEF_MAX_CURRENT_BUS;
+ if (!of_property_read_u32(np, "max-bp-current", property_u32))
+ hub->max_current_bp = min_t(u8, be32_to_cpu(*property_u32) / 2,
+ 250);
+
+ hub->power_on_time = USB251XB_DEF_POWER_ON_TIME;
+ if (!of_property_read_u32(np, "power-on-time", property_u32))
+ hub->power_on_time = min_t(u8, be32_to_cpu(*property_u32) / 2,
+ 255);
+
+ if (of_property_read_u16_array(np, "language-id", &hub->lang_id, 1))
+ hub->lang_id = USB251XB_DEF_LANGUAGE_ID;
+
+ cproperty_char = of_get_property(np, "manufacturer", NULL);
+ strlcpy(str, cproperty_char ? : USB251XB_DEF_MANUFACTURER_STRING,
+ sizeof(str));
+ hub->manufacturer_len = strlen(str) & 0xFF;
+ memset(hub->manufacturer, 0, USB251XB_STRING_BUFSIZE);
+ len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+ len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+ (wchar_t *)hub->manufacturer,
+ USB251XB_STRING_BUFSIZE);
+
+ cproperty_char = of_get_property(np, "product", NULL);
+ strlcpy(str, cproperty_char ? : data->product_str, sizeof(str));
+ hub->product_len = strlen(str) & 0xFF;
+ memset(hub->product, 0, USB251XB_STRING_BUFSIZE);
+ len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+ len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+ (wchar_t *)hub->product,
+ USB251XB_STRING_BUFSIZE);
+
+ cproperty_char = of_get_property(np, "serial", NULL);
+ strlcpy(str, cproperty_char ? : USB251XB_DEF_SERIAL_STRING,
+ sizeof(str));
+ hub->serial_len = strlen(str) & 0xFF;
+ memset(hub->serial, 0, USB251XB_STRING_BUFSIZE);
+ len = min_t(size_t, USB251XB_STRING_BUFSIZE / 2, strlen(str));
+ len = utf8s_to_utf16s(str, len, UTF16_LITTLE_ENDIAN,
+ (wchar_t *)hub->serial,
+ USB251XB_STRING_BUFSIZE);
+
+ /* The following parameters are currently not exposed to devicetree, but
+ * may be as soon as needed.
+ */
+ hub->bat_charge_en = USB251XB_DEF_BATTERY_CHARGING_ENABLE;
+ hub->boost_up = USB251XB_DEF_BOOST_UP;
+ hub->boost_x = USB251XB_DEF_BOOST_X;
+ hub->port_swap = USB251XB_DEF_PORT_SWAP;
+ hub->port_map12 = USB251XB_DEF_PORT_MAP_12;
+ hub->port_map34 = USB251XB_DEF_PORT_MAP_34;
+
+ return 0;
+}
+
+static const struct of_device_id usb251xb_of_match[] = {
+ {
+ .compatible = "microchip,usb2512b",
+ .data = &usb2512b_data,
+ }, {
+ .compatible = "microchip,usb2512bi",
+ .data = &usb2512bi_data,
+ }, {
+ .compatible = "microchip,usb2513b",
+ .data = &usb2513b_data,
+ }, {
+ .compatible = "microchip,usb2513bi",
+ .data = &usb2513bi_data,
+ }, {
+ .compatible = "microchip,usb2514b",
+ .data = &usb2514b_data,
+ }, {
+ .compatible = "microchip,usb2514bi",
+ .data = &usb2514bi_data,
+ }, {
+ /* sentinel */
+ }
+};
+MODULE_DEVICE_TABLE(of, usb251xb_of_match);
+#else /* CONFIG_OF */
+static int usb251xb_get_ofdata(struct usb251xb *hub,
+ struct usb251xb_data *data)
+{
+ return 0;
+}
+#endif /* CONFIG_OF */
+
+static int usb251xb_probe(struct usb251xb *hub)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+ const struct of_device_id *of_id = of_match_device(usb251xb_of_match,
+ dev);
+ int err;
+
+ if (np) {
+ err = usb251xb_get_ofdata(hub,
+ (struct usb251xb_data *)of_id->data);
+ if (err) {
+ dev_err(dev, "failed to get ofdata: %d\n", err);
+ return err;
+ }
+ }
+
+ err = usb251xb_connect(hub);
+ if (err) {
+ dev_err(dev, "Failed to connect hub (%d)\n", err);
+ return err;
+ }
+
+ dev_info(dev, "Hub probed successfully\n");
+
+ return 0;
+}
+
+static int usb251xb_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct usb251xb *hub;
+
+ hub = devm_kzalloc(&i2c->dev, sizeof(struct usb251xb), GFP_KERNEL);
+ if (!hub)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, hub);
+ hub->dev = &i2c->dev;
+ hub->i2c = i2c;
+
+ return usb251xb_probe(hub);
+}
+
+static const struct i2c_device_id usb251xb_id[] = {
+ { "usb2512b", 0 },
+ { "usb2512bi", 0 },
+ { "usb2513b", 0 },
+ { "usb2513bi", 0 },
+ { "usb2514b", 0 },
+ { "usb2514bi", 0 },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(i2c, usb251xb_id);
+
+static struct i2c_driver usb251xb_i2c_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = of_match_ptr(usb251xb_of_match),
+ },
+ .probe = usb251xb_i2c_probe,
+ .id_table = usb251xb_id,
+};
+
+module_i2c_driver(usb251xb_i2c_driver);
+
+MODULE_AUTHOR("Richard Leitner <richard.leitner@xxxxxxxxxxx>");
+MODULE_DESCRIPTION("USB251xB/xBi USB 2.0 Hub Controller Driver");
+MODULE_LICENSE("GPL");
--
2.1.4