[PATCH 2/2] fpga: zynq: Add support for encrypted bitstreams

From: mdf
Date: Tue Feb 14 2017 - 19:31:50 EST


From: Moritz Fischer <moritz.fischer@xxxxxxxxx>

Add support for encrypted bitstreams. For this to work the system
must be booted in secure mode.

In order for on-the-fly decryption to work, the PCAP clock rate
needs to be lowered via the PCAP_RATE_EN bit.

Signed-off-by: Moritz Fischer <moritz.fischer@xxxxxxxxx>
Cc: Alan Tull <atull@xxxxxxxxxx>
Cc: Michal Simek <michal.simek@xxxxxxxxxx>
Cc: SÃren Brinkmann <soren.brinkmann@xxxxxxxxxx>
Cc: linux-kernel@xxxxxxxxxxxxxxx
Cc: linux-fpga@xxxxxxxxxxxxxxx
---
drivers/fpga/zynq-fpga.c | 28 +++++++++++++++++++++++++---
1 file changed, 25 insertions(+), 3 deletions(-)

diff --git a/drivers/fpga/zynq-fpga.c b/drivers/fpga/zynq-fpga.c
index cb3caf5..52dabfc 100644
--- a/drivers/fpga/zynq-fpga.c
+++ b/drivers/fpga/zynq-fpga.c
@@ -72,6 +72,10 @@
#define CTRL_PCAP_PR_MASK BIT(27)
/* Enable PCAP */
#define CTRL_PCAP_MODE_MASK BIT(26)
+/* Lower rate to allow decrypt on the fly */
+#define CTRL_PCAP_RATE_EN_MASK BIT(25)
+/* System booted in secure mode */
+#define CTRL_SEC_EN_MASK BIT(7)

/* Miscellaneous Control Register bit definitions */
/* Internal PCAP loopback */
@@ -264,6 +268,17 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr,
if (err)
return err;

+ /* check if bitstream is encrypted & and system's still secure */
+ if (info->flags & FPGA_MGR_DECRYPT_BITSTREAM) {
+ ctrl = zynq_fpga_read(priv, CTRL_OFFSET);
+ if (!(ctrl & CTRL_SEC_EN_MASK)) {
+ dev_err(&mgr->dev,
+ "System not secure, can't use crypted bitstreams\n");
+ err = -EINVAL;
+ goto out_err;
+ }
+ }
+
/* don't globally reset PL if we're doing partial reconfig */
if (!(info->flags & FPGA_MGR_PARTIAL_RECONFIG)) {
if (!zynq_fpga_has_sync(buf, count)) {
@@ -335,12 +350,19 @@ static int zynq_fpga_ops_write_init(struct fpga_manager *mgr,

/* set configuration register with following options:
* - enable PCAP interface
- * - set throughput for maximum speed
+ * - set throughput for maximum speed (if bistream not crypted)
* - set CPU in user mode
*/
ctrl = zynq_fpga_read(priv, CTRL_OFFSET);
- zynq_fpga_write(priv, CTRL_OFFSET,
- (CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK | ctrl));
+ if (info->flags & FPGA_MGR_DECRYPT_BITSTREAM)
+ zynq_fpga_write(priv, CTRL_OFFSET,
+ (CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK
+ | CTRL_PCAP_RATE_EN_MASK | ctrl));
+ else
+ zynq_fpga_write(priv, CTRL_OFFSET,
+ (CTRL_PCAP_PR_MASK | CTRL_PCAP_MODE_MASK
+ | ctrl));
+

/* We expect that the command queue is empty right now. */
status = zynq_fpga_read(priv, STATUS_OFFSET);
--
2.7.4