Re: [PATCH V8 08/10] ras: acpi / apei: generate trace event for unrecognized CPER section

[Baicar, Tyler]

On 2/15/2017 8:52 AM, Steven Rostedt wrote:
> On Wed,  1 Feb 2017 10:16:51 -0700
> Tyler Baicar <tbaicar@xxxxxxxxxxxxxx> wrote:
>
> > @@ -452,11 +454,21 @@ static void ghes_do_proc(struct ghes *ghes,
> >   {
> >   	int sev, sec_sev;
> >   	struct acpi_hest_generic_data *gdata;
> > +	uuid_le sec_type;
> > +	uuid_le *fru_id = &NULL_UUID_LE;
> > +	char *fru_text = "";
> >   
> >   	sev = ghes_severity(estatus->error_severity);
> >   	apei_estatus_for_each_section(estatus, gdata) {
> >   		sec_sev = ghes_severity(gdata->error_severity);
> > -		if (!uuid_le_cmp(*(uuid_le *)gdata->section_type,
> > +		sec_type = *(uuid_le *)gdata->section_type;
> > +
> > +		if (gdata->validation_bits & CPER_SEC_VALID_FRU_ID)
> > +			fru_id = (uuid_le *)gdata->fru_id;
> > +		if (gdata->validation_bits & CPER_SEC_VALID_FRU_TEXT)
> > +			fru_text = gdata->fru_text;
> > +
> > +		if (!uuid_le_cmp(sec_type,
> >   				 CPER_SEC_PLATFORM_MEM)) {
> >   			struct cper_sec_mem_err *mem_err;
> >   
> > @@ -467,7 +479,7 @@ static void ghes_do_proc(struct ghes *ghes,
> >   			ghes_handle_memory_failure(gdata, sev);
> >   		}
> >   #ifdef CONFIG_ACPI_APEI_PCIEAER
> > -		else if (!uuid_le_cmp(*(uuid_le *)gdata->section_type,
> > +		else if (!uuid_le_cmp(sec_type,
> >   				      CPER_SEC_PCIE)) {
> >   			struct cper_sec_pcie *pcie_err;
> >   
> > @@ -500,6 +512,12 @@ static void ghes_do_proc(struct ghes *ghes,
> >   
> >   		}
> >   #endif
> > +		else {
> As an optimization, you can add:
>
> 		else if (trace_unknown_sec_event_enabled()) {
>
> instead, as then this wont be called unless the tracepoint is
> activated. Will keep the logic from doing anything with
> acpi_hest_generic_data_payload().
>
> Note, that trace_*_enabled() is activated via a jump_label, thus
> there's no branches involved.
>
> -- Steve
Hello Steve,

In v9 I currently have this and the ARM trace event from this series 
both wrapped in an
ifdef verifying that CONFIG_RAS is enabled. This resolves the kbuild 
failures and
will have this code compiled out when that config isn't enabled. Do you 
think I
should use the ifdef or use these *_enabled() functions?

Thanks,
Tyler
> > +			void *unknown_err = acpi_hest_generic_data_payload(gdata);
> > +			trace_unknown_sec_event(&sec_type,
> > +					fru_id, fru_text, sec_sev,
> > +					unknown_err, gdata->error_data_length);
> > +		}
> >   	}
> >   }
> >   

--
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project.