[PATCH 2/2] mfd: add TI LMU driver
From: Milo Kim
Date: Tue Feb 28 2017 - 01:49:37 EST
TI LMU (Lighting Management Unit) driver supports lighting devices below.
LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
LMU devices have common features.
- I2C interface for accessing device registers
- Hardware enable pin control
- Backlight brightness control
- Notifier for hardware fault monitoring
- Regulators for LCD display bias
It contains fault monitor, backlight, LED and regulator driver.
LMU fault monitor
-----------------
LM3633 and LM3697 provide hardware monitoring feature.
It enables open or short circuit detection.
After monitoring is done, each device should be re-initialized.
Notifier is used for this case.
Separate patch for 'ti-lmu-fault-monitor' will be sent later.
Backlight
---------
It's handled by TI LMU backlight consolidated driver and
chip dependent data. Separate patchset will be sent later.
LED indicator
-------------
LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
supported. Separate patch for 'leds-lm3633' will be sent later.
Regulator
---------
LM3631 has 5 regulators for the display bias.
LM3632 supports 3 regulators. One consolidated driver enables it.
The lm363x regulator driver is already upstreamed.
Acked-by: Lee Jones <lee.jones@xxxxxxxxxx>
Signed-off-by: Milo Kim <milo.kim@xxxxxx>
---
drivers/mfd/Kconfig | 12 ++
drivers/mfd/Makefile | 2 +
drivers/mfd/ti-lmu.c | 259 +++++++++++++++++++++++++++++++++
include/linux/mfd/ti-lmu-register.h | 280 ++++++++++++++++++++++++++++++++++++
include/linux/mfd/ti-lmu.h | 87 +++++++++++
5 files changed, 640 insertions(+)
create mode 100644 drivers/mfd/ti-lmu.c
create mode 100644 include/linux/mfd/ti-lmu-register.h
create mode 100644 include/linux/mfd/ti-lmu.h
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 55ecdfb74d31..75e749c1ff1a 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -1164,6 +1164,18 @@ config MFD_LP8788
TI LP8788 PMU supports regulators, battery charger, RTC,
ADC, backlight driver and current sinks.
+config MFD_TI_LMU
+ tristate "TI Lighting Management Unit driver"
+ depends on I2C
+ select MFD_CORE
+ select REGMAP_I2C
+ help
+ Say yes here to enable support for TI LMU chips.
+
+ TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
+ It consists of backlight, LED and regulator driver.
+ It provides consistent device controls for lighting functions.
+
config MFD_OMAP_USB_HOST
bool "TI OMAP USBHS core and TLL driver"
depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 31ce07611a6f..dac78a0f23a7 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -125,6 +125,8 @@ obj-$(CONFIG_MFD_AXP20X_RSB) += axp20x-rsb.o
obj-$(CONFIG_MFD_LP3943) += lp3943.o
obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o
+obj-$(CONFIG_MFD_TI_LMU) += ti-lmu.o
+
da9055-objs := da9055-core.o da9055-i2c.o
obj-$(CONFIG_MFD_DA9055) += da9055.o
obj-$(CONFIG_MFD_DA9062) += da9062-core.o
diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c
new file mode 100644
index 000000000000..cfb411cde51c
--- /dev/null
+++ b/drivers/mfd/ti-lmu.c
@@ -0,0 +1,259 @@
+/*
+ * TI LMU (Lighting Management Unit) Core Driver
+ *
+ * Copyright 2017 Texas Instruments
+ *
+ * Author: Milo Kim <milo.kim@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/mfd/core.h>
+#include <linux/mfd/ti-lmu.h>
+#include <linux/mfd/ti-lmu-register.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/slab.h>
+
+struct ti_lmu_data {
+ struct mfd_cell *cells;
+ int num_cells;
+ unsigned int max_register;
+};
+
+static int ti_lmu_enable_hw(struct ti_lmu *lmu, enum ti_lmu_id id)
+{
+ int ret;
+
+ if (gpio_is_valid(lmu->en_gpio)) {
+ ret = devm_gpio_request_one(lmu->dev, lmu->en_gpio,
+ GPIOF_OUT_INIT_HIGH, "lmu_hwen");
+ if (ret) {
+ dev_err(lmu->dev, "Can not request enable GPIO: %d\n",
+ ret);
+ return ret;
+ }
+ }
+
+ /* Delay about 1ms after HW enable pin control */
+ usleep_range(1000, 1500);
+
+ /* LM3631 has additional power up sequence - enable LCD_EN bit. */
+ if (id == LM3631) {
+ return regmap_update_bits(lmu->regmap, LM3631_REG_DEVCTRL,
+ LM3631_LCD_EN_MASK,
+ LM3631_LCD_EN_MASK);
+ }
+
+ return 0;
+}
+
+static void ti_lmu_disable_hw(struct ti_lmu *lmu)
+{
+ if (gpio_is_valid(lmu->en_gpio))
+ gpio_set_value(lmu->en_gpio, 0);
+}
+
+static struct mfd_cell lm3532_devices[] = {
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3532,
+ .of_compatible = "ti,lm3532-backlight",
+ },
+};
+
+#define LM363X_REGULATOR(_id) \
+{ \
+ .name = "lm363x-regulator", \
+ .id = _id, \
+ .of_compatible = "ti,lm363x-regulator", \
+} \
+
+static struct mfd_cell lm3631_devices[] = {
+ LM363X_REGULATOR(LM3631_BOOST),
+ LM363X_REGULATOR(LM3631_LDO_CONT),
+ LM363X_REGULATOR(LM3631_LDO_OREF),
+ LM363X_REGULATOR(LM3631_LDO_POS),
+ LM363X_REGULATOR(LM3631_LDO_NEG),
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3631,
+ .of_compatible = "ti,lm3631-backlight",
+ },
+};
+
+static struct mfd_cell lm3632_devices[] = {
+ LM363X_REGULATOR(LM3632_BOOST),
+ LM363X_REGULATOR(LM3632_LDO_POS),
+ LM363X_REGULATOR(LM3632_LDO_NEG),
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3632,
+ .of_compatible = "ti,lm3632-backlight",
+ },
+};
+
+static struct mfd_cell lm3633_devices[] = {
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3633,
+ .of_compatible = "ti,lm3633-backlight",
+ },
+ {
+ .name = "lm3633-leds",
+ .of_compatible = "ti,lm3633-leds",
+ },
+ /* Monitoring driver for open/short circuit detection */
+ {
+ .name = "ti-lmu-fault-monitor",
+ .id = LM3633,
+ .of_compatible = "ti,lm3633-fault-monitor",
+ },
+};
+
+static struct mfd_cell lm3695_devices[] = {
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3695,
+ .of_compatible = "ti,lm3695-backlight",
+ },
+};
+
+static struct mfd_cell lm3697_devices[] = {
+ {
+ .name = "ti-lmu-backlight",
+ .id = LM3697,
+ .of_compatible = "ti,lm3697-backlight",
+ },
+ /* Monitoring driver for open/short circuit detection */
+ {
+ .name = "ti-lmu-fault-monitor",
+ .id = LM3697,
+ .of_compatible = "ti,lm3697-fault-monitor",
+ },
+};
+
+#define TI_LMU_DATA(chip, max_reg) \
+static const struct ti_lmu_data chip##_data = \
+{ \
+ .cells = chip##_devices, \
+ .num_cells = ARRAY_SIZE(chip##_devices),\
+ .max_register = max_reg, \
+} \
+
+TI_LMU_DATA(lm3532, LM3532_MAX_REG);
+TI_LMU_DATA(lm3631, LM3631_MAX_REG);
+TI_LMU_DATA(lm3632, LM3632_MAX_REG);
+TI_LMU_DATA(lm3633, LM3633_MAX_REG);
+TI_LMU_DATA(lm3695, LM3695_MAX_REG);
+TI_LMU_DATA(lm3697, LM3697_MAX_REG);
+
+static const struct of_device_id ti_lmu_of_match[] = {
+ { .compatible = "ti,lm3532", .data = &lm3532_data },
+ { .compatible = "ti,lm3631", .data = &lm3631_data },
+ { .compatible = "ti,lm3632", .data = &lm3632_data },
+ { .compatible = "ti,lm3633", .data = &lm3633_data },
+ { .compatible = "ti,lm3695", .data = &lm3695_data },
+ { .compatible = "ti,lm3697", .data = &lm3697_data },
+ { }
+};
+MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
+
+static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id)
+{
+ struct device *dev = &cl->dev;
+ const struct of_device_id *match;
+ const struct ti_lmu_data *data;
+ struct regmap_config regmap_cfg;
+ struct ti_lmu *lmu;
+ int ret;
+
+ match = of_match_device(ti_lmu_of_match, dev);
+ if (!match)
+ return -ENODEV;
+ /*
+ * Get device specific data from of_match table.
+ * This data is defined by using TI_LMU_DATA() macro.
+ */
+ data = (struct ti_lmu_data *)match->data;
+
+ lmu = devm_kzalloc(dev, sizeof(*lmu), GFP_KERNEL);
+ if (!lmu)
+ return -ENOMEM;
+
+ lmu->dev = &cl->dev;
+
+ /* Setup regmap */
+ memset(®map_cfg, 0, sizeof(struct regmap_config));
+ regmap_cfg.reg_bits = 8;
+ regmap_cfg.val_bits = 8;
+ regmap_cfg.name = id->name;
+ regmap_cfg.max_register = data->max_register;
+
+ lmu->regmap = devm_regmap_init_i2c(cl, ®map_cfg);
+ if (IS_ERR(lmu->regmap))
+ return PTR_ERR(lmu->regmap);
+
+ /* HW enable pin control and additional power up sequence if required */
+ lmu->en_gpio = of_get_named_gpio(dev->of_node, "enable-gpios", 0);
+ ret = ti_lmu_enable_hw(lmu, id->driver_data);
+ if (ret)
+ return ret;
+
+ /*
+ * Fault circuit(open/short) can be detected by ti-lmu-fault-monitor.
+ * After fault detection is done, some devices should re-initialize
+ * configuration. The notifier enables such kind of handling.
+ */
+ BLOCKING_INIT_NOTIFIER_HEAD(&lmu->notifier);
+
+ i2c_set_clientdata(cl, lmu);
+
+ return mfd_add_devices(lmu->dev, 0, data->cells,
+ data->num_cells, NULL, 0, NULL);
+}
+
+static int ti_lmu_remove(struct i2c_client *cl)
+{
+ struct ti_lmu *lmu = i2c_get_clientdata(cl);
+
+ ti_lmu_disable_hw(lmu);
+ mfd_remove_devices(lmu->dev);
+ return 0;
+}
+
+static const struct i2c_device_id ti_lmu_ids[] = {
+ { "lm3532", LM3532 },
+ { "lm3631", LM3631 },
+ { "lm3632", LM3632 },
+ { "lm3633", LM3633 },
+ { "lm3695", LM3695 },
+ { "lm3697", LM3697 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);
+
+static struct i2c_driver ti_lmu_driver = {
+ .probe = ti_lmu_probe,
+ .remove = ti_lmu_remove,
+ .driver = {
+ .name = "ti-lmu",
+ .of_match_table = ti_lmu_of_match,
+ },
+ .id_table = ti_lmu_ids,
+};
+
+module_i2c_driver(ti_lmu_driver);
+
+MODULE_DESCRIPTION("TI LMU MFD Core Driver");
+MODULE_AUTHOR("Milo Kim");
+MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/ti-lmu-register.h b/include/linux/mfd/ti-lmu-register.h
new file mode 100644
index 000000000000..2125c7c02818
--- /dev/null
+++ b/include/linux/mfd/ti-lmu-register.h
@@ -0,0 +1,280 @@
+/*
+ * TI LMU (Lighting Management Unit) Device Register Map
+ *
+ * Copyright 2017 Texas Instruments
+ *
+ * Author: Milo Kim <milo.kim@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MFD_TI_LMU_REGISTER_H__
+#define __MFD_TI_LMU_REGISTER_H__
+
+#include <linux/bitops.h>
+
+/* LM3532 */
+#define LM3532_REG_OUTPUT_CFG 0x10
+#define LM3532_ILED1_CFG_MASK 0x03
+#define LM3532_ILED2_CFG_MASK 0x0C
+#define LM3532_ILED3_CFG_MASK 0x30
+#define LM3532_ILED1_CFG_SHIFT 0
+#define LM3532_ILED2_CFG_SHIFT 2
+#define LM3532_ILED3_CFG_SHIFT 4
+
+#define LM3532_REG_RAMPUP 0x12
+#define LM3532_REG_RAMPDN LM3532_REG_RAMPUP
+#define LM3532_RAMPUP_MASK 0x07
+#define LM3532_RAMPUP_SHIFT 0
+#define LM3532_RAMPDN_MASK 0x38
+#define LM3532_RAMPDN_SHIFT 3
+
+#define LM3532_REG_ENABLE 0x1D
+
+#define LM3532_REG_PWM_A_CFG 0x13
+#define LM3532_PWM_A_MASK 0x05 /* zone 0 */
+#define LM3532_PWM_ZONE_0 BIT(2)
+
+#define LM3532_REG_PWM_B_CFG 0x14
+#define LM3532_PWM_B_MASK 0x09 /* zone 1 */
+#define LM3532_PWM_ZONE_1 BIT(3)
+
+#define LM3532_REG_PWM_C_CFG 0x15
+#define LM3532_PWM_C_MASK 0x11 /* zone 2 */
+#define LM3532_PWM_ZONE_2 BIT(4)
+
+#define LM3532_REG_ZONE_CFG_A 0x16
+#define LM3532_REG_ZONE_CFG_B 0x18
+#define LM3532_REG_ZONE_CFG_C 0x1A
+#define LM3532_ZONE_MASK (BIT(2) | BIT(3) | BIT(4))
+#define LM3532_ZONE_0 0
+#define LM3532_ZONE_1 BIT(2)
+#define LM3532_ZONE_2 BIT(3)
+
+#define LM3532_REG_BRT_A 0x70 /* zone 0 */
+#define LM3532_REG_BRT_B 0x76 /* zone 1 */
+#define LM3532_REG_BRT_C 0x7C /* zone 2 */
+
+#define LM3532_MAX_REG 0x7E
+
+/* LM3631 */
+#define LM3631_REG_DEVCTRL 0x00
+#define LM3631_LCD_EN_MASK BIT(1)
+#define LM3631_BL_EN_MASK BIT(0)
+
+#define LM3631_REG_BRT_LSB 0x01
+#define LM3631_REG_BRT_MSB 0x02
+
+#define LM3631_REG_BL_CFG 0x06
+#define LM3631_BL_CHANNEL_MASK BIT(3)
+#define LM3631_BL_DUAL_CHANNEL 0
+#define LM3631_BL_SINGLE_CHANNEL BIT(3)
+#define LM3631_MAP_MASK BIT(5)
+#define LM3631_EXPONENTIAL_MAP 0
+
+#define LM3631_REG_BRT_MODE 0x08
+#define LM3631_MODE_MASK (BIT(1) | BIT(2) | BIT(3))
+#define LM3631_DEFAULT_MODE (BIT(1) | BIT(3))
+
+#define LM3631_REG_SLOPE 0x09
+#define LM3631_SLOPE_MASK 0xF0
+#define LM3631_SLOPE_SHIFT 4
+
+#define LM3631_REG_LDO_CTRL1 0x0A
+#define LM3631_EN_OREF_MASK BIT(0)
+#define LM3631_EN_VNEG_MASK BIT(1)
+#define LM3631_EN_VPOS_MASK BIT(2)
+
+#define LM3631_REG_LDO_CTRL2 0x0B
+#define LM3631_EN_CONT_MASK BIT(0)
+
+#define LM3631_REG_VOUT_CONT 0x0C
+#define LM3631_VOUT_CONT_MASK (BIT(6) | BIT(7))
+
+#define LM3631_REG_VOUT_BOOST 0x0C
+#define LM3631_REG_VOUT_POS 0x0D
+#define LM3631_REG_VOUT_NEG 0x0E
+#define LM3631_REG_VOUT_OREF 0x0F
+#define LM3631_VOUT_MASK 0x3F
+
+#define LM3631_REG_ENTIME_VCONT 0x0B
+#define LM3631_ENTIME_CONT_MASK 0x70
+
+#define LM3631_REG_ENTIME_VOREF 0x0F
+#define LM3631_REG_ENTIME_VPOS 0x10
+#define LM3631_REG_ENTIME_VNEG 0x11
+#define LM3631_ENTIME_MASK 0xF0
+#define LM3631_ENTIME_SHIFT 4
+
+#define LM3631_MAX_REG 0x16
+
+/* LM3632 */
+#define LM3632_REG_CONFIG1 0x02
+#define LM3632_OVP_MASK (BIT(5) | BIT(6) | BIT(7))
+#define LM3632_OVP_25V BIT(6)
+
+#define LM3632_REG_CONFIG2 0x03
+#define LM3632_SWFREQ_MASK BIT(7)
+#define LM3632_SWFREQ_1MHZ BIT(7)
+
+#define LM3632_REG_BRT_LSB 0x04
+#define LM3632_REG_BRT_MSB 0x05
+
+#define LM3632_REG_IO_CTRL 0x09
+#define LM3632_PWM_MASK BIT(6)
+#define LM3632_I2C_MODE 0
+#define LM3632_PWM_MODE BIT(6)
+
+#define LM3632_REG_ENABLE 0x0A
+#define LM3632_BL_EN_MASK BIT(0)
+#define LM3632_BL_CHANNEL_MASK (BIT(3) | BIT(4))
+#define LM3632_BL_SINGLE_CHANNEL BIT(4)
+#define LM3632_BL_DUAL_CHANNEL BIT(3)
+
+#define LM3632_REG_BIAS_CONFIG 0x0C
+#define LM3632_EXT_EN_MASK BIT(0)
+#define LM3632_EN_VNEG_MASK BIT(1)
+#define LM3632_EN_VPOS_MASK BIT(2)
+
+#define LM3632_REG_VOUT_BOOST 0x0D
+#define LM3632_REG_VOUT_POS 0x0E
+#define LM3632_REG_VOUT_NEG 0x0F
+#define LM3632_VOUT_MASK 0x3F
+
+#define LM3632_MAX_REG 0x10
+
+/* LM3633 */
+#define LM3633_REG_HVLED_OUTPUT_CFG 0x10
+#define LM3633_HVLED1_CFG_MASK BIT(0)
+#define LM3633_HVLED2_CFG_MASK BIT(1)
+#define LM3633_HVLED3_CFG_MASK BIT(2)
+#define LM3633_HVLED1_CFG_SHIFT 0
+#define LM3633_HVLED2_CFG_SHIFT 1
+#define LM3633_HVLED3_CFG_SHIFT 2
+
+#define LM3633_REG_BANK_SEL 0x11
+
+#define LM3633_REG_BL0_RAMP 0x12
+#define LM3633_REG_BL1_RAMP 0x13
+#define LM3633_BL_RAMPUP_MASK 0xF0
+#define LM3633_BL_RAMPUP_SHIFT 4
+#define LM3633_BL_RAMPDN_MASK 0x0F
+#define LM3633_BL_RAMPDN_SHIFT 0
+
+#define LM3633_REG_BL_RAMP_CONF 0x1B
+#define LM3633_BL_RAMP_MASK 0x0F
+#define LM3633_BL_RAMP_EACH 0x05
+
+#define LM3633_REG_PTN0_RAMP 0x1C
+#define LM3633_REG_PTN1_RAMP 0x1D
+#define LM3633_PTN_RAMPUP_MASK 0x70
+#define LM3633_PTN_RAMPUP_SHIFT 4
+#define LM3633_PTN_RAMPDN_MASK 0x07
+#define LM3633_PTN_RAMPDN_SHIFT 0
+
+#define LM3633_REG_LED_MAPPING_MODE 0x1F
+#define LM3633_LED_EXPONENTIAL BIT(1)
+
+#define LM3633_REG_IMAX_HVLED_A 0x20
+#define LM3633_REG_IMAX_HVLED_B 0x21
+#define LM3633_REG_IMAX_LVLED_BASE 0x22
+
+#define LM3633_REG_BL_FEEDBACK_ENABLE 0x28
+
+#define LM3633_REG_ENABLE 0x2B
+#define LM3633_LED_BANK_OFFSET 2
+
+#define LM3633_REG_PATTERN 0x2C
+
+#define LM3633_REG_BOOST_CFG 0x2D
+#define LM3633_OVP_MASK (BIT(1) | BIT(2))
+#define LM3633_OVP_40V 0x6
+
+#define LM3633_REG_PWM_CFG 0x2F
+#define LM3633_PWM_A_MASK BIT(0)
+#define LM3633_PWM_B_MASK BIT(1)
+
+#define LM3633_REG_BRT_HVLED_A_LSB 0x40
+#define LM3633_REG_BRT_HVLED_A_MSB 0x41
+#define LM3633_REG_BRT_HVLED_B_LSB 0x42
+#define LM3633_REG_BRT_HVLED_B_MSB 0x43
+
+#define LM3633_REG_BRT_LVLED_BASE 0x44
+
+#define LM3633_REG_PTN_DELAY 0x50
+
+#define LM3633_REG_PTN_LOWTIME 0x51
+
+#define LM3633_REG_PTN_HIGHTIME 0x52
+
+#define LM3633_REG_PTN_LOWBRT 0x53
+
+#define LM3633_REG_PTN_HIGHBRT LM3633_REG_BRT_LVLED_BASE
+
+#define LM3633_REG_BL_OPEN_FAULT_STATUS 0xB0
+
+#define LM3633_REG_BL_SHORT_FAULT_STATUS 0xB2
+
+#define LM3633_REG_MONITOR_ENABLE 0xB4
+
+#define LM3633_MAX_REG 0xB4
+
+/* LM3695 */
+#define LM3695_REG_GP 0x10
+#define LM3695_BL_CHANNEL_MASK BIT(3)
+#define LM3695_BL_DUAL_CHANNEL 0
+#define LM3695_BL_SINGLE_CHANNEL BIT(3)
+#define LM3695_BRT_RW_MASK BIT(2)
+#define LM3695_BL_EN_MASK BIT(0)
+
+#define LM3695_REG_BRT_LSB 0x13
+#define LM3695_REG_BRT_MSB 0x14
+
+#define LM3695_MAX_REG 0x14
+
+/* LM3697 */
+#define LM3697_REG_HVLED_OUTPUT_CFG 0x10
+#define LM3697_HVLED1_CFG_MASK BIT(0)
+#define LM3697_HVLED2_CFG_MASK BIT(1)
+#define LM3697_HVLED3_CFG_MASK BIT(2)
+#define LM3697_HVLED1_CFG_SHIFT 0
+#define LM3697_HVLED2_CFG_SHIFT 1
+#define LM3697_HVLED3_CFG_SHIFT 2
+
+#define LM3697_REG_BL0_RAMP 0x11
+#define LM3697_REG_BL1_RAMP 0x12
+#define LM3697_RAMPUP_MASK 0xF0
+#define LM3697_RAMPUP_SHIFT 4
+#define LM3697_RAMPDN_MASK 0x0F
+#define LM3697_RAMPDN_SHIFT 0
+
+#define LM3697_REG_RAMP_CONF 0x14
+#define LM3697_RAMP_MASK 0x0F
+#define LM3697_RAMP_EACH 0x05
+
+#define LM3697_REG_PWM_CFG 0x1C
+#define LM3697_PWM_A_MASK BIT(0)
+#define LM3697_PWM_B_MASK BIT(1)
+
+#define LM3697_REG_IMAX_A 0x17
+#define LM3697_REG_IMAX_B 0x18
+
+#define LM3697_REG_FEEDBACK_ENABLE 0x19
+
+#define LM3697_REG_BRT_A_LSB 0x20
+#define LM3697_REG_BRT_A_MSB 0x21
+#define LM3697_REG_BRT_B_LSB 0x22
+#define LM3697_REG_BRT_B_MSB 0x23
+
+#define LM3697_REG_ENABLE 0x24
+
+#define LM3697_REG_OPEN_FAULT_STATUS 0xB0
+
+#define LM3697_REG_SHORT_FAULT_STATUS 0xB2
+
+#define LM3697_REG_MONITOR_ENABLE 0xB4
+
+#define LM3697_MAX_REG 0xB4
+#endif
diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h
new file mode 100644
index 000000000000..09d5f30384e5
--- /dev/null
+++ b/include/linux/mfd/ti-lmu.h
@@ -0,0 +1,87 @@
+/*
+ * TI LMU (Lighting Management Unit) Devices
+ *
+ * Copyright 2017 Texas Instruments
+ *
+ * Author: Milo Kim <milo.kim@xxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __MFD_TI_LMU_H__
+#define __MFD_TI_LMU_H__
+
+#include <linux/gpio.h>
+#include <linux/notifier.h>
+#include <linux/regmap.h>
+
+/* Notifier event */
+#define LMU_EVENT_MONITOR_DONE 0x01
+
+enum ti_lmu_id {
+ LM3532,
+ LM3631,
+ LM3632,
+ LM3633,
+ LM3695,
+ LM3697,
+ LMU_MAX_ID,
+};
+
+enum ti_lmu_max_current {
+ LMU_IMAX_5mA,
+ LMU_IMAX_6mA,
+ LMU_IMAX_7mA = 0x03,
+ LMU_IMAX_8mA,
+ LMU_IMAX_9mA,
+ LMU_IMAX_10mA = 0x07,
+ LMU_IMAX_11mA,
+ LMU_IMAX_12mA,
+ LMU_IMAX_13mA,
+ LMU_IMAX_14mA,
+ LMU_IMAX_15mA = 0x0D,
+ LMU_IMAX_16mA,
+ LMU_IMAX_17mA,
+ LMU_IMAX_18mA,
+ LMU_IMAX_19mA,
+ LMU_IMAX_20mA = 0x13,
+ LMU_IMAX_21mA,
+ LMU_IMAX_22mA,
+ LMU_IMAX_23mA = 0x17,
+ LMU_IMAX_24mA,
+ LMU_IMAX_25mA,
+ LMU_IMAX_26mA,
+ LMU_IMAX_27mA = 0x1C,
+ LMU_IMAX_28mA,
+ LMU_IMAX_29mA,
+ LMU_IMAX_30mA,
+};
+
+enum lm363x_regulator_id {
+ LM3631_BOOST, /* Boost output */
+ LM3631_LDO_CONT, /* Display panel controller */
+ LM3631_LDO_OREF, /* Gamma reference */
+ LM3631_LDO_POS, /* Positive display bias output */
+ LM3631_LDO_NEG, /* Negative display bias output */
+ LM3632_BOOST, /* Boost output */
+ LM3632_LDO_POS, /* Positive display bias output */
+ LM3632_LDO_NEG, /* Negative display bias output */
+};
+
+/**
+ * struct ti_lmu
+ *
+ * @dev: Parent device pointer
+ * @regmap: Used for i2c communcation on accessing registers
+ * @en_gpio: GPIO for HWEN pin [Optional]
+ * @notifier: Notifier for reporting hwmon event
+ */
+struct ti_lmu {
+ struct device *dev;
+ struct regmap *regmap;
+ int en_gpio;
+ struct blocking_notifier_head notifier;
+};
+#endif
--
2.11.0