Re: [linux-sunxi] [PATCH 2/3] ARM: dts: sun8i: add usb_otg and OHCI/EHCI for usbc0 on H3

[Chen-Yu Tsai]

On Tue, Feb 28, 2017 at 11:57 PM, Icenowy Zheng <icenowy@xxxxxxxx> wrote:
>
>
> 28.02.2017, 23:46, "Chen-Yu Tsai" <wens@xxxxxxxx>:
>> On Tue, Feb 28, 2017 at 11:27 PM, Icenowy Zheng <icenowy@xxxxxxxx> wrote:
>>>  Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
>>>  or MUSB controller.
>>>
>>>  Add device nodes for these controllers.
>>>
>>>  Signed-off-by: Icenowy Zheng <icenowy@xxxxxxxx>
>>>  ---
>>>   arch/arm/boot/dts/sun8i-h3.dtsi | 36 ++++++++++++++++++++++++++++++++++++
>>>   1 file changed, 36 insertions(+)
>>>
>>>  diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
>>>  index 27780b97c863..bc9a53edf371 100644
>>>  --- a/arch/arm/boot/dts/sun8i-h3.dtsi
>>>  +++ b/arch/arm/boot/dts/sun8i-h3.dtsi
>>>  @@ -206,6 +206,19 @@
>>>                          #size-cells = <0>;
>>>                  };
>>>
>>>  + usb_otg: usb@01c19000 {
>>>  + compatible = "allwinner,sun8i-h3-musb";
>>>  + reg = <0x01c19000 0x0400>;
>>>  + clocks = <&ccu CLK_BUS_OTG>;
>>>  + resets = <&ccu RST_BUS_OTG>;
>>>  + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
>>>  + interrupt-names = "mc";
>>>  + phys = <&usbphy 0>;
>>>  + phy-names = "usb";
>>>  + extcon = <&usbphy 0>;
>>>  + status = "disabled";
>>>  + };
>>>  +
>>>                  usbphy: phy@01c19400 {
>>>                          compatible = "allwinner,sun8i-h3-usb-phy";
>>>                          reg = <0x01c19400 0x2c>,
>>>  @@ -238,6 +251,29 @@
>>>                          #phy-cells = <1>;
>>>                  };
>>>
>>>  + ehci0: usb@01c1a000 {
>>>  + compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
>>>  + reg = <0x01c1a000 0x100>;
>>>  + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
>>>  + clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
>>>  + resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
>>>  + phys = <&usbphy 0>;
>>>  + phy-names = "usb";
>>
>> So this bit is slightly concerning. IIRC the xHCI drivers power on the phy when
>> probed, which means VBUS is _always_ going to be powered on, even when it's
>> supposed to be in peripheral mode. You're probably going to need to rework
>> either the phy or the musb driver to cope with this.
>>
>> Or maybe just dropping the phy handle here and letting the musb driver handle
>> it would work, but that requires the musb driver be loaded.
>
> In fact the MUSB driver is always needed -- to set the dr_mode.

I guess it's the same with DWC2/3 that have host controller pairs.

> And currently MUSB driver can take over the USB bus even if it's host-only by forcing
> its mode in sysfs.

IIUC that would also switch the phy muxing over to the HCI pairs.

ChenYu

>>
>> ChenYu
>>
>>>  + status = "disabled";
>>>  + };
>>>  +
>>>  + ohci0: usb@01c1a400 {
>>>  + compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
>>>  + reg = <0x01c1a400 0x100>;
>>>  + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
>>>  + clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
>>>  + <&ccu CLK_USB_OHCI0>;
>>>  + resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
>>>  + phys = <&usbphy 0>;
>>>  + phy-names = "usb";
>>>  + status = "disabled";
>>>  + };
>>>  +
>>>                  ehci1: usb@01c1b000 {
>>>                          compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
>>>                          reg = <0x01c1b000 0x100>;
>>>  --
>>>  2.11.1
>>>
>>>  --
>>>  You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>>>  To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
>>>  For more options, visit https://groups.google.com/d/optout.
>>
>> --
>> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
>> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
>> For more options, visit https://groups.google.com/d/optout.
>
> --
> You received this message because you are subscribed to the Google Groups "linux-sunxi" group.
> To unsubscribe from this group and stop receiving emails from it, send an email to linux-sunxi+unsubscribe@xxxxxxxxxxxxxxxxx
> For more options, visit https://groups.google.com/d/optout.