Re: [PATCH 2/2] mfd: add TI LMU driver
From: Lee Jones
Date: Tue Mar 14 2017 - 12:44:51 EST
On Tue, 28 Feb 2017, Milo Kim wrote:
> TI LMU (Lighting Management Unit) driver supports lighting devices below.
>
> LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
>
> LMU devices have common features.
> - I2C interface for accessing device registers
> - Hardware enable pin control
> - Backlight brightness control
> - Notifier for hardware fault monitoring
> - Regulators for LCD display bias
>
> It contains fault monitor, backlight, LED and regulator driver.
>
> LMU fault monitor
> -----------------
> LM3633 and LM3697 provide hardware monitoring feature.
> It enables open or short circuit detection.
> After monitoring is done, each device should be re-initialized.
> Notifier is used for this case.
> Separate patch for 'ti-lmu-fault-monitor' will be sent later.
>
> Backlight
> ---------
> It's handled by TI LMU backlight consolidated driver and
> chip dependent data. Separate patchset will be sent later.
>
> LED indicator
> -------------
> LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
> supported. Separate patch for 'leds-lm3633' will be sent later.
>
> Regulator
> ---------
> LM3631 has 5 regulators for the display bias.
> LM3632 supports 3 regulators. One consolidated driver enables it.
> The lm363x regulator driver is already upstreamed.
>
> Acked-by: Lee Jones <lee.jones@xxxxxxxxxx>
> Signed-off-by: Milo Kim <milo.kim@xxxxxx>
> ---
> drivers/mfd/Kconfig | 12 ++
> drivers/mfd/Makefile | 2 +
> drivers/mfd/ti-lmu.c | 259 +++++++++++++++++++++++++++++++++
> include/linux/mfd/ti-lmu-register.h | 280 ++++++++++++++++++++++++++++++++++++
> include/linux/mfd/ti-lmu.h | 87 +++++++++++
> 5 files changed, 640 insertions(+)
> create mode 100644 drivers/mfd/ti-lmu.c
> create mode 100644 include/linux/mfd/ti-lmu-register.h
> create mode 100644 include/linux/mfd/ti-lmu.h
Applied, thanks.
> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
> index 55ecdfb74d31..75e749c1ff1a 100644
> --- a/drivers/mfd/Kconfig
> +++ b/drivers/mfd/Kconfig
> @@ -1164,6 +1164,18 @@ config MFD_LP8788
> TI LP8788 PMU supports regulators, battery charger, RTC,
> ADC, backlight driver and current sinks.
>
> +config MFD_TI_LMU
> + tristate "TI Lighting Management Unit driver"
> + depends on I2C
> + select MFD_CORE
> + select REGMAP_I2C
> + help
> + Say yes here to enable support for TI LMU chips.
> +
> + TI LMU MFD supports LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
> + It consists of backlight, LED and regulator driver.
> + It provides consistent device controls for lighting functions.
> +
> config MFD_OMAP_USB_HOST
> bool "TI OMAP USBHS core and TLL driver"
> depends on USB_EHCI_HCD_OMAP || USB_OHCI_HCD_OMAP3
> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
> index 31ce07611a6f..dac78a0f23a7 100644
> --- a/drivers/mfd/Makefile
> +++ b/drivers/mfd/Makefile
> @@ -125,6 +125,8 @@ obj-$(CONFIG_MFD_AXP20X_RSB) += axp20x-rsb.o
> obj-$(CONFIG_MFD_LP3943) += lp3943.o
> obj-$(CONFIG_MFD_LP8788) += lp8788.o lp8788-irq.o
>
> +obj-$(CONFIG_MFD_TI_LMU) += ti-lmu.o
> +
> da9055-objs := da9055-core.o da9055-i2c.o
> obj-$(CONFIG_MFD_DA9055) += da9055.o
> obj-$(CONFIG_MFD_DA9062) += da9062-core.o
> diff --git a/drivers/mfd/ti-lmu.c b/drivers/mfd/ti-lmu.c
> new file mode 100644
> index 000000000000..cfb411cde51c
> --- /dev/null
> +++ b/drivers/mfd/ti-lmu.c
> @@ -0,0 +1,259 @@
> +/*
> + * TI LMU (Lighting Management Unit) Core Driver
> + *
> + * Copyright 2017 Texas Instruments
> + *
> + * Author: Milo Kim <milo.kim@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/err.h>
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/core.h>
> +#include <linux/mfd/ti-lmu.h>
> +#include <linux/mfd/ti-lmu-register.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/of_gpio.h>
> +#include <linux/slab.h>
> +
> +struct ti_lmu_data {
> + struct mfd_cell *cells;
> + int num_cells;
> + unsigned int max_register;
> +};
> +
> +static int ti_lmu_enable_hw(struct ti_lmu *lmu, enum ti_lmu_id id)
> +{
> + int ret;
> +
> + if (gpio_is_valid(lmu->en_gpio)) {
> + ret = devm_gpio_request_one(lmu->dev, lmu->en_gpio,
> + GPIOF_OUT_INIT_HIGH, "lmu_hwen");
> + if (ret) {
> + dev_err(lmu->dev, "Can not request enable GPIO: %d\n",
> + ret);
> + return ret;
> + }
> + }
> +
> + /* Delay about 1ms after HW enable pin control */
> + usleep_range(1000, 1500);
> +
> + /* LM3631 has additional power up sequence - enable LCD_EN bit. */
> + if (id == LM3631) {
> + return regmap_update_bits(lmu->regmap, LM3631_REG_DEVCTRL,
> + LM3631_LCD_EN_MASK,
> + LM3631_LCD_EN_MASK);
> + }
> +
> + return 0;
> +}
> +
> +static void ti_lmu_disable_hw(struct ti_lmu *lmu)
> +{
> + if (gpio_is_valid(lmu->en_gpio))
> + gpio_set_value(lmu->en_gpio, 0);
> +}
> +
> +static struct mfd_cell lm3532_devices[] = {
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3532,
> + .of_compatible = "ti,lm3532-backlight",
> + },
> +};
> +
> +#define LM363X_REGULATOR(_id) \
> +{ \
> + .name = "lm363x-regulator", \
> + .id = _id, \
> + .of_compatible = "ti,lm363x-regulator", \
> +} \
> +
> +static struct mfd_cell lm3631_devices[] = {
> + LM363X_REGULATOR(LM3631_BOOST),
> + LM363X_REGULATOR(LM3631_LDO_CONT),
> + LM363X_REGULATOR(LM3631_LDO_OREF),
> + LM363X_REGULATOR(LM3631_LDO_POS),
> + LM363X_REGULATOR(LM3631_LDO_NEG),
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3631,
> + .of_compatible = "ti,lm3631-backlight",
> + },
> +};
> +
> +static struct mfd_cell lm3632_devices[] = {
> + LM363X_REGULATOR(LM3632_BOOST),
> + LM363X_REGULATOR(LM3632_LDO_POS),
> + LM363X_REGULATOR(LM3632_LDO_NEG),
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3632,
> + .of_compatible = "ti,lm3632-backlight",
> + },
> +};
> +
> +static struct mfd_cell lm3633_devices[] = {
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3633,
> + .of_compatible = "ti,lm3633-backlight",
> + },
> + {
> + .name = "lm3633-leds",
> + .of_compatible = "ti,lm3633-leds",
> + },
> + /* Monitoring driver for open/short circuit detection */
> + {
> + .name = "ti-lmu-fault-monitor",
> + .id = LM3633,
> + .of_compatible = "ti,lm3633-fault-monitor",
> + },
> +};
> +
> +static struct mfd_cell lm3695_devices[] = {
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3695,
> + .of_compatible = "ti,lm3695-backlight",
> + },
> +};
> +
> +static struct mfd_cell lm3697_devices[] = {
> + {
> + .name = "ti-lmu-backlight",
> + .id = LM3697,
> + .of_compatible = "ti,lm3697-backlight",
> + },
> + /* Monitoring driver for open/short circuit detection */
> + {
> + .name = "ti-lmu-fault-monitor",
> + .id = LM3697,
> + .of_compatible = "ti,lm3697-fault-monitor",
> + },
> +};
> +
> +#define TI_LMU_DATA(chip, max_reg) \
> +static const struct ti_lmu_data chip##_data = \
> +{ \
> + .cells = chip##_devices, \
> + .num_cells = ARRAY_SIZE(chip##_devices),\
> + .max_register = max_reg, \
> +} \
> +
> +TI_LMU_DATA(lm3532, LM3532_MAX_REG);
> +TI_LMU_DATA(lm3631, LM3631_MAX_REG);
> +TI_LMU_DATA(lm3632, LM3632_MAX_REG);
> +TI_LMU_DATA(lm3633, LM3633_MAX_REG);
> +TI_LMU_DATA(lm3695, LM3695_MAX_REG);
> +TI_LMU_DATA(lm3697, LM3697_MAX_REG);
> +
> +static const struct of_device_id ti_lmu_of_match[] = {
> + { .compatible = "ti,lm3532", .data = &lm3532_data },
> + { .compatible = "ti,lm3631", .data = &lm3631_data },
> + { .compatible = "ti,lm3632", .data = &lm3632_data },
> + { .compatible = "ti,lm3633", .data = &lm3633_data },
> + { .compatible = "ti,lm3695", .data = &lm3695_data },
> + { .compatible = "ti,lm3697", .data = &lm3697_data },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, ti_lmu_of_match);
> +
> +static int ti_lmu_probe(struct i2c_client *cl, const struct i2c_device_id *id)
> +{
> + struct device *dev = &cl->dev;
> + const struct of_device_id *match;
> + const struct ti_lmu_data *data;
> + struct regmap_config regmap_cfg;
> + struct ti_lmu *lmu;
> + int ret;
> +
> + match = of_match_device(ti_lmu_of_match, dev);
> + if (!match)
> + return -ENODEV;
> + /*
> + * Get device specific data from of_match table.
> + * This data is defined by using TI_LMU_DATA() macro.
> + */
> + data = (struct ti_lmu_data *)match->data;
> +
> + lmu = devm_kzalloc(dev, sizeof(*lmu), GFP_KERNEL);
> + if (!lmu)
> + return -ENOMEM;
> +
> + lmu->dev = &cl->dev;
> +
> + /* Setup regmap */
> + memset(®map_cfg, 0, sizeof(struct regmap_config));
> + regmap_cfg.reg_bits = 8;
> + regmap_cfg.val_bits = 8;
> + regmap_cfg.name = id->name;
> + regmap_cfg.max_register = data->max_register;
> +
> + lmu->regmap = devm_regmap_init_i2c(cl, ®map_cfg);
> + if (IS_ERR(lmu->regmap))
> + return PTR_ERR(lmu->regmap);
> +
> + /* HW enable pin control and additional power up sequence if required */
> + lmu->en_gpio = of_get_named_gpio(dev->of_node, "enable-gpios", 0);
> + ret = ti_lmu_enable_hw(lmu, id->driver_data);
> + if (ret)
> + return ret;
> +
> + /*
> + * Fault circuit(open/short) can be detected by ti-lmu-fault-monitor.
> + * After fault detection is done, some devices should re-initialize
> + * configuration. The notifier enables such kind of handling.
> + */
> + BLOCKING_INIT_NOTIFIER_HEAD(&lmu->notifier);
> +
> + i2c_set_clientdata(cl, lmu);
> +
> + return mfd_add_devices(lmu->dev, 0, data->cells,
> + data->num_cells, NULL, 0, NULL);
> +}
> +
> +static int ti_lmu_remove(struct i2c_client *cl)
> +{
> + struct ti_lmu *lmu = i2c_get_clientdata(cl);
> +
> + ti_lmu_disable_hw(lmu);
> + mfd_remove_devices(lmu->dev);
> + return 0;
> +}
> +
> +static const struct i2c_device_id ti_lmu_ids[] = {
> + { "lm3532", LM3532 },
> + { "lm3631", LM3631 },
> + { "lm3632", LM3632 },
> + { "lm3633", LM3633 },
> + { "lm3695", LM3695 },
> + { "lm3697", LM3697 },
> + { }
> +};
> +MODULE_DEVICE_TABLE(i2c, ti_lmu_ids);
> +
> +static struct i2c_driver ti_lmu_driver = {
> + .probe = ti_lmu_probe,
> + .remove = ti_lmu_remove,
> + .driver = {
> + .name = "ti-lmu",
> + .of_match_table = ti_lmu_of_match,
> + },
> + .id_table = ti_lmu_ids,
> +};
> +
> +module_i2c_driver(ti_lmu_driver);
> +
> +MODULE_DESCRIPTION("TI LMU MFD Core Driver");
> +MODULE_AUTHOR("Milo Kim");
> +MODULE_LICENSE("GPL v2");
> diff --git a/include/linux/mfd/ti-lmu-register.h b/include/linux/mfd/ti-lmu-register.h
> new file mode 100644
> index 000000000000..2125c7c02818
> --- /dev/null
> +++ b/include/linux/mfd/ti-lmu-register.h
> @@ -0,0 +1,280 @@
> +/*
> + * TI LMU (Lighting Management Unit) Device Register Map
> + *
> + * Copyright 2017 Texas Instruments
> + *
> + * Author: Milo Kim <milo.kim@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef __MFD_TI_LMU_REGISTER_H__
> +#define __MFD_TI_LMU_REGISTER_H__
> +
> +#include <linux/bitops.h>
> +
> +/* LM3532 */
> +#define LM3532_REG_OUTPUT_CFG 0x10
> +#define LM3532_ILED1_CFG_MASK 0x03
> +#define LM3532_ILED2_CFG_MASK 0x0C
> +#define LM3532_ILED3_CFG_MASK 0x30
> +#define LM3532_ILED1_CFG_SHIFT 0
> +#define LM3532_ILED2_CFG_SHIFT 2
> +#define LM3532_ILED3_CFG_SHIFT 4
> +
> +#define LM3532_REG_RAMPUP 0x12
> +#define LM3532_REG_RAMPDN LM3532_REG_RAMPUP
> +#define LM3532_RAMPUP_MASK 0x07
> +#define LM3532_RAMPUP_SHIFT 0
> +#define LM3532_RAMPDN_MASK 0x38
> +#define LM3532_RAMPDN_SHIFT 3
> +
> +#define LM3532_REG_ENABLE 0x1D
> +
> +#define LM3532_REG_PWM_A_CFG 0x13
> +#define LM3532_PWM_A_MASK 0x05 /* zone 0 */
> +#define LM3532_PWM_ZONE_0 BIT(2)
> +
> +#define LM3532_REG_PWM_B_CFG 0x14
> +#define LM3532_PWM_B_MASK 0x09 /* zone 1 */
> +#define LM3532_PWM_ZONE_1 BIT(3)
> +
> +#define LM3532_REG_PWM_C_CFG 0x15
> +#define LM3532_PWM_C_MASK 0x11 /* zone 2 */
> +#define LM3532_PWM_ZONE_2 BIT(4)
> +
> +#define LM3532_REG_ZONE_CFG_A 0x16
> +#define LM3532_REG_ZONE_CFG_B 0x18
> +#define LM3532_REG_ZONE_CFG_C 0x1A
> +#define LM3532_ZONE_MASK (BIT(2) | BIT(3) | BIT(4))
> +#define LM3532_ZONE_0 0
> +#define LM3532_ZONE_1 BIT(2)
> +#define LM3532_ZONE_2 BIT(3)
> +
> +#define LM3532_REG_BRT_A 0x70 /* zone 0 */
> +#define LM3532_REG_BRT_B 0x76 /* zone 1 */
> +#define LM3532_REG_BRT_C 0x7C /* zone 2 */
> +
> +#define LM3532_MAX_REG 0x7E
> +
> +/* LM3631 */
> +#define LM3631_REG_DEVCTRL 0x00
> +#define LM3631_LCD_EN_MASK BIT(1)
> +#define LM3631_BL_EN_MASK BIT(0)
> +
> +#define LM3631_REG_BRT_LSB 0x01
> +#define LM3631_REG_BRT_MSB 0x02
> +
> +#define LM3631_REG_BL_CFG 0x06
> +#define LM3631_BL_CHANNEL_MASK BIT(3)
> +#define LM3631_BL_DUAL_CHANNEL 0
> +#define LM3631_BL_SINGLE_CHANNEL BIT(3)
> +#define LM3631_MAP_MASK BIT(5)
> +#define LM3631_EXPONENTIAL_MAP 0
> +
> +#define LM3631_REG_BRT_MODE 0x08
> +#define LM3631_MODE_MASK (BIT(1) | BIT(2) | BIT(3))
> +#define LM3631_DEFAULT_MODE (BIT(1) | BIT(3))
> +
> +#define LM3631_REG_SLOPE 0x09
> +#define LM3631_SLOPE_MASK 0xF0
> +#define LM3631_SLOPE_SHIFT 4
> +
> +#define LM3631_REG_LDO_CTRL1 0x0A
> +#define LM3631_EN_OREF_MASK BIT(0)
> +#define LM3631_EN_VNEG_MASK BIT(1)
> +#define LM3631_EN_VPOS_MASK BIT(2)
> +
> +#define LM3631_REG_LDO_CTRL2 0x0B
> +#define LM3631_EN_CONT_MASK BIT(0)
> +
> +#define LM3631_REG_VOUT_CONT 0x0C
> +#define LM3631_VOUT_CONT_MASK (BIT(6) | BIT(7))
> +
> +#define LM3631_REG_VOUT_BOOST 0x0C
> +#define LM3631_REG_VOUT_POS 0x0D
> +#define LM3631_REG_VOUT_NEG 0x0E
> +#define LM3631_REG_VOUT_OREF 0x0F
> +#define LM3631_VOUT_MASK 0x3F
> +
> +#define LM3631_REG_ENTIME_VCONT 0x0B
> +#define LM3631_ENTIME_CONT_MASK 0x70
> +
> +#define LM3631_REG_ENTIME_VOREF 0x0F
> +#define LM3631_REG_ENTIME_VPOS 0x10
> +#define LM3631_REG_ENTIME_VNEG 0x11
> +#define LM3631_ENTIME_MASK 0xF0
> +#define LM3631_ENTIME_SHIFT 4
> +
> +#define LM3631_MAX_REG 0x16
> +
> +/* LM3632 */
> +#define LM3632_REG_CONFIG1 0x02
> +#define LM3632_OVP_MASK (BIT(5) | BIT(6) | BIT(7))
> +#define LM3632_OVP_25V BIT(6)
> +
> +#define LM3632_REG_CONFIG2 0x03
> +#define LM3632_SWFREQ_MASK BIT(7)
> +#define LM3632_SWFREQ_1MHZ BIT(7)
> +
> +#define LM3632_REG_BRT_LSB 0x04
> +#define LM3632_REG_BRT_MSB 0x05
> +
> +#define LM3632_REG_IO_CTRL 0x09
> +#define LM3632_PWM_MASK BIT(6)
> +#define LM3632_I2C_MODE 0
> +#define LM3632_PWM_MODE BIT(6)
> +
> +#define LM3632_REG_ENABLE 0x0A
> +#define LM3632_BL_EN_MASK BIT(0)
> +#define LM3632_BL_CHANNEL_MASK (BIT(3) | BIT(4))
> +#define LM3632_BL_SINGLE_CHANNEL BIT(4)
> +#define LM3632_BL_DUAL_CHANNEL BIT(3)
> +
> +#define LM3632_REG_BIAS_CONFIG 0x0C
> +#define LM3632_EXT_EN_MASK BIT(0)
> +#define LM3632_EN_VNEG_MASK BIT(1)
> +#define LM3632_EN_VPOS_MASK BIT(2)
> +
> +#define LM3632_REG_VOUT_BOOST 0x0D
> +#define LM3632_REG_VOUT_POS 0x0E
> +#define LM3632_REG_VOUT_NEG 0x0F
> +#define LM3632_VOUT_MASK 0x3F
> +
> +#define LM3632_MAX_REG 0x10
> +
> +/* LM3633 */
> +#define LM3633_REG_HVLED_OUTPUT_CFG 0x10
> +#define LM3633_HVLED1_CFG_MASK BIT(0)
> +#define LM3633_HVLED2_CFG_MASK BIT(1)
> +#define LM3633_HVLED3_CFG_MASK BIT(2)
> +#define LM3633_HVLED1_CFG_SHIFT 0
> +#define LM3633_HVLED2_CFG_SHIFT 1
> +#define LM3633_HVLED3_CFG_SHIFT 2
> +
> +#define LM3633_REG_BANK_SEL 0x11
> +
> +#define LM3633_REG_BL0_RAMP 0x12
> +#define LM3633_REG_BL1_RAMP 0x13
> +#define LM3633_BL_RAMPUP_MASK 0xF0
> +#define LM3633_BL_RAMPUP_SHIFT 4
> +#define LM3633_BL_RAMPDN_MASK 0x0F
> +#define LM3633_BL_RAMPDN_SHIFT 0
> +
> +#define LM3633_REG_BL_RAMP_CONF 0x1B
> +#define LM3633_BL_RAMP_MASK 0x0F
> +#define LM3633_BL_RAMP_EACH 0x05
> +
> +#define LM3633_REG_PTN0_RAMP 0x1C
> +#define LM3633_REG_PTN1_RAMP 0x1D
> +#define LM3633_PTN_RAMPUP_MASK 0x70
> +#define LM3633_PTN_RAMPUP_SHIFT 4
> +#define LM3633_PTN_RAMPDN_MASK 0x07
> +#define LM3633_PTN_RAMPDN_SHIFT 0
> +
> +#define LM3633_REG_LED_MAPPING_MODE 0x1F
> +#define LM3633_LED_EXPONENTIAL BIT(1)
> +
> +#define LM3633_REG_IMAX_HVLED_A 0x20
> +#define LM3633_REG_IMAX_HVLED_B 0x21
> +#define LM3633_REG_IMAX_LVLED_BASE 0x22
> +
> +#define LM3633_REG_BL_FEEDBACK_ENABLE 0x28
> +
> +#define LM3633_REG_ENABLE 0x2B
> +#define LM3633_LED_BANK_OFFSET 2
> +
> +#define LM3633_REG_PATTERN 0x2C
> +
> +#define LM3633_REG_BOOST_CFG 0x2D
> +#define LM3633_OVP_MASK (BIT(1) | BIT(2))
> +#define LM3633_OVP_40V 0x6
> +
> +#define LM3633_REG_PWM_CFG 0x2F
> +#define LM3633_PWM_A_MASK BIT(0)
> +#define LM3633_PWM_B_MASK BIT(1)
> +
> +#define LM3633_REG_BRT_HVLED_A_LSB 0x40
> +#define LM3633_REG_BRT_HVLED_A_MSB 0x41
> +#define LM3633_REG_BRT_HVLED_B_LSB 0x42
> +#define LM3633_REG_BRT_HVLED_B_MSB 0x43
> +
> +#define LM3633_REG_BRT_LVLED_BASE 0x44
> +
> +#define LM3633_REG_PTN_DELAY 0x50
> +
> +#define LM3633_REG_PTN_LOWTIME 0x51
> +
> +#define LM3633_REG_PTN_HIGHTIME 0x52
> +
> +#define LM3633_REG_PTN_LOWBRT 0x53
> +
> +#define LM3633_REG_PTN_HIGHBRT LM3633_REG_BRT_LVLED_BASE
> +
> +#define LM3633_REG_BL_OPEN_FAULT_STATUS 0xB0
> +
> +#define LM3633_REG_BL_SHORT_FAULT_STATUS 0xB2
> +
> +#define LM3633_REG_MONITOR_ENABLE 0xB4
> +
> +#define LM3633_MAX_REG 0xB4
> +
> +/* LM3695 */
> +#define LM3695_REG_GP 0x10
> +#define LM3695_BL_CHANNEL_MASK BIT(3)
> +#define LM3695_BL_DUAL_CHANNEL 0
> +#define LM3695_BL_SINGLE_CHANNEL BIT(3)
> +#define LM3695_BRT_RW_MASK BIT(2)
> +#define LM3695_BL_EN_MASK BIT(0)
> +
> +#define LM3695_REG_BRT_LSB 0x13
> +#define LM3695_REG_BRT_MSB 0x14
> +
> +#define LM3695_MAX_REG 0x14
> +
> +/* LM3697 */
> +#define LM3697_REG_HVLED_OUTPUT_CFG 0x10
> +#define LM3697_HVLED1_CFG_MASK BIT(0)
> +#define LM3697_HVLED2_CFG_MASK BIT(1)
> +#define LM3697_HVLED3_CFG_MASK BIT(2)
> +#define LM3697_HVLED1_CFG_SHIFT 0
> +#define LM3697_HVLED2_CFG_SHIFT 1
> +#define LM3697_HVLED3_CFG_SHIFT 2
> +
> +#define LM3697_REG_BL0_RAMP 0x11
> +#define LM3697_REG_BL1_RAMP 0x12
> +#define LM3697_RAMPUP_MASK 0xF0
> +#define LM3697_RAMPUP_SHIFT 4
> +#define LM3697_RAMPDN_MASK 0x0F
> +#define LM3697_RAMPDN_SHIFT 0
> +
> +#define LM3697_REG_RAMP_CONF 0x14
> +#define LM3697_RAMP_MASK 0x0F
> +#define LM3697_RAMP_EACH 0x05
> +
> +#define LM3697_REG_PWM_CFG 0x1C
> +#define LM3697_PWM_A_MASK BIT(0)
> +#define LM3697_PWM_B_MASK BIT(1)
> +
> +#define LM3697_REG_IMAX_A 0x17
> +#define LM3697_REG_IMAX_B 0x18
> +
> +#define LM3697_REG_FEEDBACK_ENABLE 0x19
> +
> +#define LM3697_REG_BRT_A_LSB 0x20
> +#define LM3697_REG_BRT_A_MSB 0x21
> +#define LM3697_REG_BRT_B_LSB 0x22
> +#define LM3697_REG_BRT_B_MSB 0x23
> +
> +#define LM3697_REG_ENABLE 0x24
> +
> +#define LM3697_REG_OPEN_FAULT_STATUS 0xB0
> +
> +#define LM3697_REG_SHORT_FAULT_STATUS 0xB2
> +
> +#define LM3697_REG_MONITOR_ENABLE 0xB4
> +
> +#define LM3697_MAX_REG 0xB4
> +#endif
> diff --git a/include/linux/mfd/ti-lmu.h b/include/linux/mfd/ti-lmu.h
> new file mode 100644
> index 000000000000..09d5f30384e5
> --- /dev/null
> +++ b/include/linux/mfd/ti-lmu.h
> @@ -0,0 +1,87 @@
> +/*
> + * TI LMU (Lighting Management Unit) Devices
> + *
> + * Copyright 2017 Texas Instruments
> + *
> + * Author: Milo Kim <milo.kim@xxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +#ifndef __MFD_TI_LMU_H__
> +#define __MFD_TI_LMU_H__
> +
> +#include <linux/gpio.h>
> +#include <linux/notifier.h>
> +#include <linux/regmap.h>
> +
> +/* Notifier event */
> +#define LMU_EVENT_MONITOR_DONE 0x01
> +
> +enum ti_lmu_id {
> + LM3532,
> + LM3631,
> + LM3632,
> + LM3633,
> + LM3695,
> + LM3697,
> + LMU_MAX_ID,
> +};
> +
> +enum ti_lmu_max_current {
> + LMU_IMAX_5mA,
> + LMU_IMAX_6mA,
> + LMU_IMAX_7mA = 0x03,
> + LMU_IMAX_8mA,
> + LMU_IMAX_9mA,
> + LMU_IMAX_10mA = 0x07,
> + LMU_IMAX_11mA,
> + LMU_IMAX_12mA,
> + LMU_IMAX_13mA,
> + LMU_IMAX_14mA,
> + LMU_IMAX_15mA = 0x0D,
> + LMU_IMAX_16mA,
> + LMU_IMAX_17mA,
> + LMU_IMAX_18mA,
> + LMU_IMAX_19mA,
> + LMU_IMAX_20mA = 0x13,
> + LMU_IMAX_21mA,
> + LMU_IMAX_22mA,
> + LMU_IMAX_23mA = 0x17,
> + LMU_IMAX_24mA,
> + LMU_IMAX_25mA,
> + LMU_IMAX_26mA,
> + LMU_IMAX_27mA = 0x1C,
> + LMU_IMAX_28mA,
> + LMU_IMAX_29mA,
> + LMU_IMAX_30mA,
> +};
> +
> +enum lm363x_regulator_id {
> + LM3631_BOOST, /* Boost output */
> + LM3631_LDO_CONT, /* Display panel controller */
> + LM3631_LDO_OREF, /* Gamma reference */
> + LM3631_LDO_POS, /* Positive display bias output */
> + LM3631_LDO_NEG, /* Negative display bias output */
> + LM3632_BOOST, /* Boost output */
> + LM3632_LDO_POS, /* Positive display bias output */
> + LM3632_LDO_NEG, /* Negative display bias output */
> +};
> +
> +/**
> + * struct ti_lmu
> + *
> + * @dev: Parent device pointer
> + * @regmap: Used for i2c communcation on accessing registers
> + * @en_gpio: GPIO for HWEN pin [Optional]
> + * @notifier: Notifier for reporting hwmon event
> + */
> +struct ti_lmu {
> + struct device *dev;
> + struct regmap *regmap;
> + int en_gpio;
> + struct blocking_notifier_head notifier;
> +};
> +#endif
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org â Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog