[PATCH 4.10 25/63] amd-xgbe: Be sure to set MDIO modes on device (re)start

[Greg Kroah-Hartman]

4.10-stable review patch.  If anyone has any objections, please let me know.

------------------

From: "Lendacky, Thomas" <Thomas.Lendacky@xxxxxxx>


[ Upstream commit b42c6761fd1651f564491b53016046c9ebf0b2a9 ]

The MDIO register mode is set when the device is probed. But when the
device is brought down and then back up, the MDIO register mode has been
reset.  Be sure to reset the mode during device startup and only change
the mode of the address specified.

Signed-off-by: Tom Lendacky <thomas.lendacky@xxxxxxx>
Signed-off-by: David S. Miller <davem@xxxxxxxxxxxxx>
Signed-off-by: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
---
 drivers/net/ethernet/amd/xgbe/xgbe-dev.c    |    2 +-
 drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c |   22 ++++++++++++++++++++++
 2 files changed, 23 insertions(+), 1 deletion(-)

--- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c
@@ -1323,7 +1323,7 @@ static int xgbe_read_ext_mii_regs(struct
 static int xgbe_set_ext_mii_mode(struct xgbe_prv_data *pdata, unsigned int port,
 				 enum xgbe_mdio_mode mode)
 {
-	unsigned int reg_val = 0;
+	unsigned int reg_val = XGMAC_IOREAD(pdata, MAC_MDIOCL22R);
 
 	switch (mode) {
 	case XGBE_MDIO_MODE_CL22:
--- a/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
+++ b/drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c
@@ -875,6 +875,16 @@ static int xgbe_phy_find_phy_device(stru
 	    !phy_data->sfp_phy_avail)
 		return 0;
 
+	/* Set the proper MDIO mode for the PHY */
+	ret = pdata->hw_if.set_ext_mii_mode(pdata, phy_data->mdio_addr,
+					    phy_data->phydev_mode);
+	if (ret) {
+		netdev_err(pdata->netdev,
+			   "mdio port/clause not compatible (%u/%u)\n",
+			   phy_data->mdio_addr, phy_data->phydev_mode);
+		return ret;
+	}
+
 	/* Create and connect to the PHY device */
 	phydev = get_phy_device(phy_data->mii, phy_data->mdio_addr,
 				(phy_data->phydev_mode == XGBE_MDIO_MODE_CL45));
@@ -2722,6 +2732,18 @@ static int xgbe_phy_start(struct xgbe_pr
 	if (ret)
 		return ret;
 
+	/* Set the proper MDIO mode for the re-driver */
+	if (phy_data->redrv && !phy_data->redrv_if) {
+		ret = pdata->hw_if.set_ext_mii_mode(pdata, phy_data->redrv_addr,
+						    XGBE_MDIO_MODE_CL22);
+		if (ret) {
+			netdev_err(pdata->netdev,
+				   "redriver mdio port not compatible (%u)\n",
+				   phy_data->redrv_addr);
+			return ret;
+		}
+	}
+
 	/* Start in highest supported mode */
 	xgbe_phy_set_mode(pdata, phy_data->start_mode);