Re: [PATCH v5 3/3] mfd: wm831x: Add device tree binding document

[Lee Jones]

On Fri, 17 Mar 2017, Charles Keepax wrote:

> Add a device tree binding document for the wm831x series of PMICs.
> Currently only support for the registering the device and the GPIOs are
> actually implemented in the driver.
> 
> Signed-off-by: Charles Keepax <ckeepax@xxxxxxxxxxxxxxxxxxxxxxxxxxx>
> ---
> 
> Changes since v4:
>  - Removed one extra level of ../ for relative links that was incorrect
> 
> Thanks,
> Charles
> 
>  Documentation/devicetree/bindings/mfd/wm831x.txt | 81 ++++++++++++++++++++++++
>  MAINTAINERS                                      |  1 +
>  2 files changed, 82 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/wm831x.txt

Applied, thanks.

> diff --git a/Documentation/devicetree/bindings/mfd/wm831x.txt b/Documentation/devicetree/bindings/mfd/wm831x.txt
> new file mode 100644
> index 0000000..9f8b743
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/wm831x.txt
> @@ -0,0 +1,81 @@
> +Cirrus Logic/Wolfson Microelectronics wm831x PMICs
> +
> +System PMICs with a wide range of additional features.
> +
> +Required properties:
> +
> +  - compatible : One of the following chip-specific strings:
> +        "wlf,wm8310"
> +        "wlf,wm8311"
> +        "wlf,wm8312"
> +        "wlf,wm8320"
> +        "wlf,wm8321"
> +        "wlf,wm8325"
> +        "wlf,wm8326"
> +
> +  - reg : I2C slave address when connected using I2C, chip select number
> +    when using SPI.
> +
> +  - gpio-controller : Indicates this device is a GPIO controller.
> +  - #gpio-cells : Must be 2. The first cell is the pin number and the
> +    second cell is used to specify optional parameters (currently unused).
> +
> +  - interrupts : The interrupt line the IRQ signal for the device is
> +    connected to.
> +  - interrupt-parent : The parent interrupt controller.
> +
> +  - interrupt-controller : wm831x devices contain interrupt controllers and
> +    may provide interrupt services to other devices.
> +  - #interrupt-cells: Must be 2. The first cell is the IRQ number, and the
> +    second cell is the flags, encoded as the trigger masks from
> +    ../interrupt-controller/interrupts.txt
> +
> +Optional sub-nodes:
> +  - regulators : Contains sub-nodes for each of the regulators supplied by
> +    the device. The regulators are bound using their names listed below:
> +
> +    dcdc1 : DCDC1
> +    dcdc2 : DCDC2
> +    dcdc3 : DCDC3
> +    dcdc4 : DCDC3
> +    isink1 : ISINK1
> +    isink2 : ISINK2
> +    ldo1 : LDO1
> +    ldo2 : LDO2
> +    ldo3 : LDO3
> +    ldo4 : LDO4
> +    ldo5 : LDO5
> +    ldo7 : LDO7
> +    ldo11 : LDO11
> +
> +    The bindings details of each regulator can be found in:
> +    ../regulator/regulator.txt
> +
> +Example:
> +
> +wm8310: pmic@36 {
> +	compatible = "wlf,wm8310";
> +	reg = <0x36>;
> +
> +	gpio-controller;
> +	#gpio-cells = <2>;
> +
> +	interrupts = <347>;
> +	interrupt-parent = <&gic>;
> +
> +	interrupt-controller;
> +	#interrupt-cells = <2>;
> +
> +	regulators {
> +		dcdc1: dcdc1 {
> +			regulator-name = "DCDC1";
> +			regulator-min-microvolt = <600000>;
> +			regulator-max-microvolt = <600000>;
> +		};
> +		ldo1: ldo1 {
> +			regulator-name = "LDO1";
> +			regulator-min-microvolt = <1700000>;
> +			regulator-max-microvolt = <1700000>;
> +		};
> +	};
> +};
> diff --git a/MAINTAINERS b/MAINTAINERS
> index c265a5f..dfe761b 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -13600,6 +13600,7 @@ F:	Documentation/hwmon/wm83??
>  F:	Documentation/devicetree/bindings/extcon/extcon-arizona.txt
>  F:	Documentation/devicetree/bindings/regulator/arizona-regulator.txt
>  F:	Documentation/devicetree/bindings/mfd/arizona.txt
> +F:	Documentation/devicetree/bindings/mfd/wm831x.txt
>  F:	arch/arm/mach-s3c64xx/mach-crag6410*
>  F:	drivers/clk/clk-wm83*.c
>  F:	drivers/extcon/extcon-arizona.c

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org â Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog