Re: [PATCH v5 0/8] Add dual-role OTG support for Allwinner H3

[Kishon Vijay Abraham I]

On Saturday 25 March 2017 08:20 PM, Icenowy Zheng wrote:
> Allwinner H3 have a its USB PHY0 routed to two USB controllers: one is
> a MUSB controller, which can work in peripheral mode, but works badly in
> host mode (several hardware will fail on the MUSB controller, even connect
> one MUSB controller in peripheral mode to another one in host mode cannot
> work); the other is a pair of EHCI/OHCI controller, which can work only
> in host mode, but have better compatibillity. The route is controlled in
> a register, which we have set it to HCI only when we do not know about
> it well.
> 
> Add support to route to the best controller according to current USB mode
> (host/peripheral).
> 
> Note: Currently even if hardware only support hostmode, we should still
> enable the MUSB controller, as it controls the USB mode. (Some this kind
> of hardware can also work in peripheral mode by settings in the sysfs
> node of MUSB, then connect it to another host via a USB Type-A to Type-A
> cable.)
> 
> Patch 1 changes the device tree binding to include the "pmu0" for HCI pair.
> 
> Patch 2 and 3 are fixes for H3 PHY, in order to make MUSB really working
> on H3.
> 
> Patch 4 adds support for auto routing of PHY0. It's currently only enabled
> on H3, but it's easy to extend it to other SoCs which feature this
> route control.

merged the 1st four patch of this series.

Thanks
Kishon

> 
> Patch 5 adds necessary device tree nodes to the H3/H5 DTSI file. Note: The
> phy is not bind for OHCI/EHCI0, as OHCI/EHCI drivers will keep the VBUS
> on. Only MUSB driver can properly handle a dual-role PHY.
> 
> Patch 6 enables USB OTG functionality on Orange Pi One board, which is
> the only H3 board I have that have proper OTG function. It's easy to
> enable OTG on other boards with their schematics.
> 
> Patch 7 enables USB OTG functionality on Orange Pi Zero board, as the
> board cannot output power on Vbus, I only enabled peripheral mode by
> default.
> 
> Patch 8 enables USB OTG funcionality on Orange Pi PC2 board, which is
> the newly support H5 board, and have USB-related pins same as Orange
> Pi One.
> 
> The USB PHY on V3s/A64 SoCs also feature this capability, and it will
> be soon enabled on these SoCs after this patchset is merged.
> 
> Icenowy Zheng (8):
>   dt: bindings: add pmu0 regs for USB PHYs on Allwinner H3/V3s/A64
>   phy: sun4i-usb: change PHYCTL register clearing code
>   phy: sun4i-usb: add PHYCTL offset for H3 SoC
>   phy: sun4i-usb: support automatically switch PHY0 route to MUSB/HCI
>   ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
>   ARM: sun8i: h3: enable USB OTG on Orange Pi One
>   ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
>   arm64: allwinner: h5: enable USB OTG on Orange Pi PC 2 board
> 
>  .../devicetree/bindings/phy/sun4i-usb-phy.txt      |  1 +
>  arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts  | 20 +++++++-
>  arch/arm/boot/dts/sun8i-h3-orangepi-one.dts        | 22 ++++++++-
>  arch/arm/boot/dts/sunxi-h3-h5.dtsi                 | 32 ++++++++++++
>  .../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts  | 27 +++++++++-
>  drivers/phy/phy-sun4i-usb.c                        | 57 ++++++++++++++--------
>  6 files changed, 135 insertions(+), 24 deletions(-)
>