Re: [PATCH v6 02/39] [media] dt-bindings: Add bindings for i.MX media driver

[Rob Herring]

On Mon, Mar 27, 2017 at 7:40 PM, Steve Longerbeam <slongerbeam@xxxxxxxxx> wrote:
> Add bindings documentation for the i.MX media driver.
>
> Signed-off-by: Steve Longerbeam <steve_longerbeam@xxxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/media/imx.txt | 74 +++++++++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/media/imx.txt
>
> diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
> new file mode 100644
> index 0000000..3059c06
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/imx.txt
> @@ -0,0 +1,74 @@
> +Freescale i.MX Media Video Device
> +=================================
> +
> +Video Media Controller node
> +---------------------------
> +
> +This is the media controller node for video capture support. It is a
> +virtual device that lists the camera serial interface nodes that the
> +media device will control.
> +
> +Required properties:
> +- compatible : "fsl,imx-capture-subsystem";
> +- ports      : Should contain a list of phandles pointing to camera
> +               sensor interface ports of IPU devices
> +
> +example:
> +
> +capture-subsystem {
> +       compatible = "fsl,imx-capture-subsystem";
> +       ports = <&ipu1_csi0>, <&ipu1_csi1>;
> +};
> +
> +fim child node
> +--------------
> +
> +This is an optional child node of the ipu_csi port nodes. If present and
> +available, it enables the Frame Interval Monitor. Its properties can be
> +used to modify the method in which the FIM measures frame intervals.
> +Refer to Documentation/media/v4l-drivers/imx.rst for more info on the
> +Frame Interval Monitor.
> +
> +Optional properties:
> +- fsl,input-capture-channel: an input capture channel and channel flags,
> +                            specified as <chan flags>. The channel number
> +                            must be 0 or 1. The flags can be
> +                            IRQ_TYPE_EDGE_RISING, IRQ_TYPE_EDGE_FALLING, or
> +                            IRQ_TYPE_EDGE_BOTH, and specify which input
> +                            capture signal edge will trigger the input
> +                            capture event. If an input capture channel is
> +                            specified, the FIM will use this method to
> +                            measure frame intervals instead of via the EOF
> +                            interrupt. The input capture method is much
> +                            preferred over EOF as it is not subject to
> +                            interrupt latency errors. However it requires
> +                            routing the VSYNC or FIELD output signals of
> +                            the camera sensor to one of the i.MX input
> +                            capture pads (SD1_DAT0, SD1_DAT1), which also
> +                            gives up support for SD1.
> +
> +
> +mipi_csi2 node
> +--------------
> +
> +This is the device node for the MIPI CSI-2 Receiver, required for MIPI
> +CSI-2 sensors.
> +
> +Required properties:
> +- compatible   : "fsl,imx6-mipi-csi2", "snps,dw-mipi-csi2";

As I mentioned in v5, there's a DW CSI2 binding in progress. This
needs to be based on that.

Rob