Re: [PATCH v1 1/1] mtd: mtk-nor: set controller's address width according to nor flash

From: Cyrille Pitchen
Date: Sun Apr 16 2017 - 13:24:36 EST


Le 13/04/2017 Ã 10:24, Cyrille Pitchen a Ãcrit :
> Hi Guochun,
>
> Le 13/04/2017 Ã 04:40, Guochun Mao a Ãcrit :
>> Hi Cyrille,
>>
>> On Wed, 2017-04-12 at 22:57 +0200, Cyrille Pitchen wrote:
>>> Hi Guochun,
>>>
>>> Le 05/04/2017 Ã 10:37, Guochun Mao a Ãcrit :
>>>> When nor's size larger than 16MByte, nor's address width maybe
>>>> set to 3 or 4, and controller should change address width according
>>>> to nor's setting.
>>>>
>>>> Signed-off-by: Guochun Mao <guochun.mao@xxxxxxxxxxxx>st
>
> Acked-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx>
>

Applied to github/spi-nor

Thanks!


>>>> ---
>>>> drivers/mtd/spi-nor/mtk-quadspi.c | 27 +++++++++++++++++++++++++++
>>>> 1 file changed, 27 insertions(+)
>>>>
>>>> diff --git a/drivers/mtd/spi-nor/mtk-quadspi.c b/drivers/mtd/spi-nor/mtk-quadspi.c
>>>> index e661877..b637770 100644
>>>> --- a/drivers/mtd/spi-nor/mtk-quadspi.c
>>>> +++ b/drivers/mtd/spi-nor/mtk-quadspi.c
>>>> @@ -104,6 +104,8 @@
>>>> #define MTK_NOR_MAX_RX_TX_SHIFT 6
>>>> /* can shift up to 56 bits (7 bytes) transfer by MTK_NOR_PRG_CMD */
>>>> #define MTK_NOR_MAX_SHIFT 7
>>>> +/* nor controller 4-byte address mode enable bit */
>>>> +#define MTK_NOR_4B_ADDR_EN BIT(4)
>>>>
>>>> /* Helpers for accessing the program data / shift data registers */
>>>> #define MTK_NOR_PRG_REG(n) (MTK_NOR_PRGDATA0_REG + 4 * (n))
>>>> @@ -230,10 +232,35 @@ static int mt8173_nor_write_buffer_disable(struct mt8173_nor *mt8173_nor)
>>>> 10000);
>>>> }
>>>>
>>>> +static void mt8173_nor_set_addr_width(struct mt8173_nor *mt8173_nor)
>>>> +{
>>>> + u8 val;
>>>> + struct spi_nor *nor = &mt8173_nor->nor;
>>>> +
>>>> + val = readb(mt8173_nor->base + MTK_NOR_DUAL_REG);
>>>> +
>>>> + switch (nor->addr_width) {
>>>> + case 3:
>>>> + val &= ~MTK_NOR_4B_ADDR_EN;
>>>> + break;
>>>> + case 4:
>>>> + val |= MTK_NOR_4B_ADDR_EN;
>>>> + break;
>>>> + default:
>>>> + dev_warn(mt8173_nor->dev, "Unexpected address width %u.\n",
>>>> + nor->addr_width);
>>>> + break;
>>>> + }
>>>> +
>>>> + writeb(val, mt8173_nor->base + MTK_NOR_DUAL_REG);
>>>> +}
>>>> +
>>>> static void mt8173_nor_set_addr(struct mt8173_nor *mt8173_nor, u32 addr)
>>>> {
>>>> int i;
>>>>
>>>> + mt8173_nor_set_addr_width(mt8173_nor);
>>>> +
>>>> for (i = 0; i < 3; i++) {
>>>
>>> Should it be 'i < nor->addr_width' instead of 'i < 3' ?
>>> Does it work when accessing data after 128Mbit ?
>>
>> Yes, it can work.
>>
>> Let's see the whole function,
>>
>> static void mt8173_nor_set_addr(struct mt8173_nor *mt8173_nor, u32 addr)
>> {
>> int i;
>>
>> mt8173_nor_set_addr_width(mt8173_nor);
>>
>> for (i = 0; i < 3; i++) {
>> writeb(addr & 0xff, mt8173_nor->base + MTK_NOR_RADR0_REG
>> + i * 4);
>> addr >>= 8;
>> }
>> /* Last register is non-contiguous */
>> writeb(addr & 0xff, mt8173_nor->base + MTK_NOR_RADR3_REG);
>> }
>>
>> The nor controller has 4 registers for address.
>> This '3' indicates the number of contiguous address' registers
>> base + MTK_NOR_RADR0_REG(0x10)
>> base + MTK_NOR_RADR1_REG(0x14)
>> base + MTK_NOR_RADR2_REG(0x18),
>> but the last address register is non-contiguous,
>> it's base + MTK_NOR_RADR3_REG(0xc8)
>>
>> mt8173_nor_set_addr will set addr into these 4 registers by Byte.
>> The bit MTK_NOR_4B_ADDR_EN will decide whether 3-byte(0x10,0x14,0x18)
>> or 4-byte(0x10,0x14,x018,0xc8) been sent to nor device.
>> and, it can access data after 128Mbit when sent 4-byte address.
>
> Indeed, you're right. Sorry for the noise!
>
>>
>> Best regards,
>>
>> Guochun
>>
>>>
>>> Best regards,
>>>
>>> Cyrille
>>>
>>>> writeb(addr & 0xff, mt8173_nor->base + MTK_NOR_RADR0_REG + i * 4);
>>>> addr >>= 8;
>>>>
>>>
>>
>>
>>
>
>
> ______________________________________________________
> Linux MTD discussion mailing list
> http://lists.infradead.org/mailman/listinfo/linux-mtd/
>