[PATCH 2/2] dt-bindings: pcie: Add documentation for Mediatek PCIe

[Ryder Lee]

Add documentation for PCIe host driver available in MT7623
series SoCs.

Signed-off-by: Ryder Lee <ryder.lee@xxxxxxxxxxxx>
---
 .../bindings/pci/mediatek,mt7623-pcie.txt          | 153 +++++++++++++++++++++
 1 file changed, 153 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt

diff --git a/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
new file mode 100644
index 0000000..ee93ba2
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/mediatek,mt7623-pcie.txt
@@ -0,0 +1,153 @@
+Mediatek MT7623 PCIe controller
+
+Required properties:
+- compatible: Should contain "mediatek,mt7623-pcie".
+- device_type: Must be "pci"
+- reg: Base addresses and lengths of the pcie controller.
+- interrupts: A list of interrupt outputs of the controller.
+- #address-cells: Address representation for root ports (must be 3)
+  - cell 0 specifies the bus and device numbers of the root port:
+    [23:16]: bus number
+    [15:11]: device number
+  - cell 1 denotes the upper 32 address bits and should be 0
+  - cell 2 contains the lower 32 address bits and is used to translate to the
+    CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - free_ck
+- power-domains: A phandle and power domain specifier pair to the power domain
+  which is responsible for collapsing and restoring power to the peripheral
+- bus-range: Range of bus numbers associated with this controller
+- ranges: Describes the translation of addresses for root ports and standard
+  PCI regions. The entries must be 6 cells each, where the first three cells
+  correspond to the address as described for the #address-cells property
+  above, the fourth cell is the physical CPU address to translate to and the
+  fifth and six cells are as described for the #size-cells property above.
+  - The first three entries are expected to translate the addresses for the root
+    port registers, which are referenced by the assigned-addresses property of
+    the root port nodes (see below).
+  - The remaining entries setup the mapping for the standard I/O and memory
+	regions.
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+
+In addition, the device tree node must have sub-nodes describing each
+PCIe interface, having the following mandatory properties:
+
+Required properties:
+- device_type: Must be "pci"
+- assigned-addresses: Address and size of the port configuration registers
+- reg: Only the first four bytes are used to refer to the correct bus number
+  and device number.
+- #address-cells: Must be 3
+- #size-cells: Must be 2
+- ranges: Sub-ranges distributed from the PCIe controller node. An empty
+  property is sufficient.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - sys_ck
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - pcie-reset
+- num-lanes: Number of lanes to use for this port.
+- phys: Must contain an entry for each entry in phy-names.
+- phy-names: Must include an entry for each sub node. Entries are of the form
+  "pcie-phyN": where N ranges from 0 to the value specified for port number.
+  See ../phy/phy-mt7623-pcie.txt for details.
+
+Examples:
+
+SoC dtsi:
+
+	pcie: pcie@1a140000 {
+		compatible = "mediatek,mt7623-pcie";
+		device_type = "pci";
+		reg = <0 0x1a140000 0 0x1000>; /* PCIe shared registers */
+		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		clocks = <&topckgen CLK_TOP_ETHIF_SEL>;
+		clock-names = "free_ck";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>;
+
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x1a142000 0 0x1a142000 0 0x1000 /* Por0 registers */
+			  0x82000000 0 0x1a143000 0 0x1a143000 0 0x1000 /* Por1 registers */
+			  0x82000000 0 0x1a144000 0 0x1a144000 0 0x1000 /* Por2 registers */
+			  0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */
+			  0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>;	/* memory space */
+		status = "disabled";
+
+		pcie@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x1a142000 0 0x1000>;
+			reg = <0x0800 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			clocks = <&hifsys CLK_HIFSYS_PCIE0>;
+			clock-names = "sys_ck";
+			resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>;
+			reset-names = "pcie-reset";
+
+			num-lanes = <1>;
+			phys = <&pcie0_phy>;
+			phy-names = "pcie-phy0";
+		};
+
+		pcie@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x1a143000 0 0x1000>;
+			reg = <0x1000 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			clocks = <&hifsys CLK_HIFSYS_PCIE1>;
+			clock-names = "sys_ck";
+			resets = <&hifsys MT2701_HIFSYS_PCIE1_RST>;
+			reset-names = "pcie-reset";
+
+			num-lanes = <1>;
+			phys = <&pcie1_phy>;
+			phy-names = "pcie-phy1";
+		};
+
+		pcie@3,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001800 0 0x1a144000 0 0x1000>;
+			reg = <0x1800 0 0 0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			clocks = <&hifsys CLK_HIFSYS_PCIE2>;
+			clock-names = "sys_ck";
+			resets = <&hifsys MT2701_HIFSYS_PCIE2_RST>;
+			reset-names = "pcie-reset";
+
+			num-lanes = <1>;
+			phys = <&pcie2_phy>;
+			phy-names = "pcie-phy2";
+		};
+	};
+
+Board dts:
+
+	&pcie {
+		status = "okay";
+
+		pcie@1,0 {
+			status = "okay";
+		};
+	};
\ No newline at end of file
-- 
1.9.1