Re: [infiniband-core] question about arguments position

[Doug Ledford]

On Thu, 2017-05-04 at 21:52 +0000, Parav Pandit wrote:
> Hi,
> 
> > 
> > -----Original Message-----
> > From: linux-rdma-owner@xxxxxxxxxxxxxxx [mailto:linux-rdma-
> > owner@xxxxxxxxxxxxxxx] On Behalf Of Gustavo A. R. Silva
> > Sent: Thursday, May 4, 2017 12:42 PM
> > To: Doug Ledford <dledford@xxxxxxxxxx>; Sean Hefty
> > <sean.hefty@xxxxxxxxx>; Hal Rosenstock <hal.rosenstock@xxxxxxxxx>;
> > Sagi
> > Grimberg <sagi@xxxxxxxxxx>; Bart Van Assche
> > <bart.vanassche@xxxxxxxxxxx>; Steve Wise <swise@xxxxxxxxxxxxxxxxxxx
> > om>;
> > Leon Romanovsky <leonro@xxxxxxxxxxxx>; Yishai Hadas
> > <yishaih@xxxxxxxxxxxx>; Moni Shoua <monis@xxxxxxxxxxxx>
> > Cc: linux-rdma@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx
> > Subject: [infiniband-core] question about arguments position
> > 
> > 
> > Hello everybody,
> > 
> > While looking into Coverity ID 1351047 I ran into the following
> > piece of code at
> > drivers/infiniband/core/verbs.c:496:
> > 
> > ret = rdma_addr_find_l2_eth_by_grh(&dgid, &sgid,
> > ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂah_attr->dmac,
> > ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂwc->wc_flags & IB_WC_WITH_VLAN
> > ?
> > ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂNULL : &vlan_id,
> > ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ&if_index, &hoplimit);
> > 
> > 
> > The issue here is that the position of arguments in the call to
> > rdma_addr_find_l2_eth_by_grh() function do not match the order of
> > the
> > parameters:
> > 
> > &dgid is passed to sgid
> > &sgid is passed to dgid
> > 
> > This is the function prototype:
> > 
> > int rdma_addr_find_l2_eth_by_grh(const union ib_gid *sgid,
> > 				Âconst union ib_gid *dgid,
> > 				Âu8 *dmac, u16 *vlan_id, int *if_index,
> > 				Âint *hoplimit)
> > 
> > My question here is if this is intentional?
> > 
> Yes. ib_init_ah_from_wc() creates ah from the incoming packet.
> Incoming packet has dgid of the receiver node on which this code is
> getting executed
> And sgid contains the GID of the sender.
> 
> When resolving mac address of destination, you use arrived dgid as
> sgid.
> And use sgid as dgid because sgid contains destinations GID whom to
> respond to.

A patch to add a comment and forestall future questions here might be a
good addition.

-- 
Doug Ledford <dledford@xxxxxxxxxx>
  GPG KeyID: B826A3330E572FDD
 Â
Key fingerprint = AE6B 1BDA 122B 23B4 265B Â1274 B826 A333 0E57 2FDD