[PATCH v2 11/18] arm64: dts: meson-gxbb-odroidc2: Fix node order

[Andreas FÃrber]

Sort nodes referenced by label alphabetically.

Signed-off-by: Andreas FÃrber <afaerber@xxxxxxx>
---
 v1 -> v2:
 * Rebased (new nodes added)
 
 .../arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 108 ++++++++++-----------
 1 file changed, 54 insertions(+), 54 deletions(-)

diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
index 54a9c6a6b392..d147c853ab05 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts
@@ -137,16 +137,6 @@
 	};
 };
 
-&scpi_clocks {
-	status = "disabled";
-};
-
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
 &ethmac {
 	status = "okay";
 	pinctrl-0 = <&eth_rgmii_pins>;
@@ -172,6 +162,33 @@
 	};
 };
 
+&gpio_ao {
+	/*
+	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&i2c_A {
+	status = "okay";
+	pinctrl-0 = <&i2c_a_pins>;
+	pinctrl-names = "default";
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
 &pinctrl_aobus {
 	gpio-line-names = "UART TX", "UART RX", "VCCK En", "TF 3V3/1V8 En",
 			  "USB HUB nRESET", "USB OTG Power En",
@@ -223,55 +240,15 @@
 			  "";
 };
 
-&ir {
-	status = "okay";
-	pinctrl-0 = <&remote_input_ao_pins>;
-	pinctrl-names = "default";
-};
-
-&i2c_A {
-	status = "okay";
-	pinctrl-0 = <&i2c_a_pins>;
-	pinctrl-names = "default";
-};
-
-&gpio_ao {
-	/*
-	 * WARNING: The USB Hub on the Odroid-C2 needs a reset signal
-	 * to be turned high in order to be detected by the USB Controller
-	 * This signal should be handled by a USB specific power sequence
-	 * in order to reset the Hub when USB bus is powered down.
-	 */
-	usb-hub {
-		gpio-hog;
-		gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "usb-hub-reset";
-	};
-};
-
-&usb0_phy {
-	status = "okay";
-	phy-supply = <&usb_otg_pwr>;
-};
-
-&usb1_phy {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
-
-&usb1 {
-	status = "okay";
-};
-
 &saradc {
 	status = "okay";
 	vref-supply = <&vcc1v8>;
 };
 
+&scpi_clocks {
+	status = "disabled";
+};
+
 /* SD */
 &sd_emmc_b {
 	status = "okay";
@@ -309,3 +286,26 @@
 	vmmc-supply = <&vcc3v3>;
 	vqmmc-supply = <&vcc1v8>;
 };
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb0_phy {
+	status = "okay";
+	phy-supply = <&usb_otg_pwr>;
+};
+
+&usb1_phy {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
-- 
2.12.0