Re: [PATCH 2/3] regulator: lp87565: Add support for lp87565 PMIC regulators
From: Andrew F. Davis
Date: Fri May 19 2017 - 11:54:19 EST
On 05/19/2017 07:42 AM, Keerthy wrote:
> The regulators set consists of 4 BUCKs. The output
> voltages are configurable and are meant to supply power to the
> main processor and other components. The ramp delay is configurable
> for all BUCKs. The BUCKs can be configured in single phase or
> multiphase modes.
>
> Signed-off-by: Keerthy <j-keerthy@xxxxxx>
> ---
> drivers/regulator/Kconfig | 8 ++
> drivers/regulator/Makefile | 1 +
> drivers/regulator/lp87565-regulator.c | 244 ++++++++++++++++++++++++++++++++++
> 3 files changed, 253 insertions(+)
> create mode 100644 drivers/regulator/lp87565-regulator.c
>
> diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
> index 48db87d..7c34ff8 100644
> --- a/drivers/regulator/Kconfig
> +++ b/drivers/regulator/Kconfig
> @@ -365,6 +365,14 @@ config REGULATOR_LP8755
> chip contains six step-down DC/DC converters which can support
> 9 mode multiphase configuration.
>
> +config REGULATOR_LP87565
> + tristate "TI LP87565 Power regulators"
> + depends on MFD_TI_LP87565 && OF
> + help
> + This driver supports LP87565 voltage regulator chips. LP87565
> + provides four step-down converters. It supports software based
> + voltage control for different voltage domains
> +
> config REGULATOR_LP8788
> tristate "TI LP8788 Power Regulators"
> depends on MFD_LP8788
> diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
> index dc3503f..fee6b8c 100644
> --- a/drivers/regulator/Makefile
> +++ b/drivers/regulator/Makefile
> @@ -46,6 +46,7 @@ obj-$(CONFIG_REGULATOR_LP3971) += lp3971.o
> obj-$(CONFIG_REGULATOR_LP3972) += lp3972.o
> obj-$(CONFIG_REGULATOR_LP872X) += lp872x.o
> obj-$(CONFIG_REGULATOR_LP873X) += lp873x-regulator.o
> +obj-$(CONFIG_REGULATOR_LP87565) += lp87565-regulator.o
> obj-$(CONFIG_REGULATOR_LP8788) += lp8788-buck.o
> obj-$(CONFIG_REGULATOR_LP8788) += lp8788-ldo.o
> obj-$(CONFIG_REGULATOR_LP8755) += lp8755.o
> diff --git a/drivers/regulator/lp87565-regulator.c b/drivers/regulator/lp87565-regulator.c
> new file mode 100644
> index 0000000..5849cf3
> --- /dev/null
> +++ b/drivers/regulator/lp87565-regulator.c
> @@ -0,0 +1,244 @@
> +/*
> + * Regulator driver for LP87565 PMIC
> + *
> + * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether expressed or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License version 2 for more details.
> + */
> +
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#include <linux/mfd/lp87565.h>
> +
> +#define LP87565_REGULATOR(_name, _id, _of, _ops, _n, _vr, _vm, _er, _em, \
> + _delay, _lr, _cr) \
> + [_id] = { \
> + .desc = { \
> + .name = _name, \
> + .supply_name = _of "-in", \
> + .id = _id, \
> + .of_match = of_match_ptr(_of), \
> + .regulators_node = of_match_ptr("regulators"),\
> + .ops = &_ops, \
> + .n_voltages = _n, \
> + .type = REGULATOR_VOLTAGE, \
> + .owner = THIS_MODULE, \
> + .vsel_reg = _vr, \
> + .vsel_mask = _vm, \
> + .enable_reg = _er, \
> + .enable_mask = _em, \
> + .ramp_delay = _delay, \
> + .linear_ranges = _lr, \
> + .n_linear_ranges = ARRAY_SIZE(_lr), \
> + }, \
> + .ctrl2_reg = _cr, \
> + }
> +
> +#define LP87565_Q1_MIN_IDX LP87565_BUCK_10
Unused?
> +
> +struct lp87565_regulator {
> + struct regulator_desc desc;
> + unsigned int ctrl2_reg;
> +};
> +
> +static const struct lp87565_regulator regulators[];
> +
> +static const struct regulator_linear_range buck0_1_2_3_ranges[] = {
> + REGULATOR_LINEAR_RANGE(500000, 0x0, 0x17, 10000),
> + REGULATOR_LINEAR_RANGE(735000, 0x18, 0x9d, 5000),
> + REGULATOR_LINEAR_RANGE(1420000, 0x9e, 0xff, 20000),
> +};
> +
> +static unsigned int lp87565_buck_ramp_delay[] = {
> + 30000, 15000, 10000, 7500, 3800, 1900, 940, 470
> +};
> +
> +/* LP87565 BUCK current limit */
> +static const unsigned int lp87565_buck_uA[] = {
> + 1500000, 2000000, 2500000, 3000000, 3500000, 4000000, 4500000, 5000000,
> +};
> +
> +static int lp87565_buck_set_ramp_delay(struct regulator_dev *rdev,
> + int ramp_delay)
> +{
> + int id = rdev_get_id(rdev);
> + struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
> + unsigned int reg;
> + int ret;
> +
> + if (ramp_delay <= 470)
> + reg = 7;
> + else if (ramp_delay <= 940)
> + reg = 6;
> + else if (ramp_delay <= 1900)
> + reg = 5;
> + else if (ramp_delay <= 3800)
> + reg = 4;
> + else if (ramp_delay <= 7500)
> + reg = 3;
> + else if (ramp_delay <= 10000)
> + reg = 2;
> + else if (ramp_delay <= 15000)
> + reg = 1;
> + else
> + reg = 0;
> +
> + ret = regmap_update_bits(lp87565->regmap, regulators[id].ctrl2_reg,
> + LP87565_BUCK_CTRL_2_SLEW_RATE,
> + reg << __ffs(LP87565_BUCK_CTRL_2_SLEW_RATE));
> + if (ret) {
> + dev_err(lp87565->dev, "SLEW RATE write failed: %d\n", ret);
> + return ret;
> + }
> +
> + rdev->constraints->ramp_delay = lp87565_buck_ramp_delay[reg];
> +
> + return 0;
> +}
> +
> +static int lp87565_buck_set_current_limit(struct regulator_dev *rdev,
> + int min_uA, int max_uA)
> +{
> + int id = rdev_get_id(rdev);
> + struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
> + int i;
> +
> + for (i = ARRAY_SIZE(lp87565_buck_uA) - 1; i >= 0; i--) {
> + if (lp87565_buck_uA[i] >= min_uA &&
> + lp87565_buck_uA[i] <= max_uA)
> + return regmap_update_bits(lp87565->regmap,
> + regulators[id].ctrl2_reg,
> + LP87565_BUCK_CTRL_2_ILIM,
> + i << __ffs(LP87565_BUCK_CTRL_2_ILIM));
> + }
> +
> + return -EINVAL;
> +}
> +
> +static int lp87565_buck_get_current_limit(struct regulator_dev *rdev)
> +{
> + int id = rdev_get_id(rdev);
> + struct lp87565 *lp87565 = rdev_get_drvdata(rdev);
> + int ret;
> + unsigned int val;
> +
> + ret = regmap_read(lp87565->regmap, regulators[id].ctrl2_reg, &val);
> + if (ret)
> + return ret;
> +
> + val = (val & LP87565_BUCK_CTRL_2_ILIM) >>
> + __ffs(LP87565_BUCK_CTRL_2_ILIM);
> +
> + return (val < ARRAY_SIZE(lp87565_buck_uA)) ?
> + lp87565_buck_uA[val] : -EINVAL;
> +}
> +
> +/* Operations permitted on BUCK0, BUCK1 */
> +static struct regulator_ops lp87565_buck_ops = {
> + .is_enabled = regulator_is_enabled_regmap,
> + .enable = regulator_enable_regmap,
> + .disable = regulator_disable_regmap,
> + .get_voltage_sel = regulator_get_voltage_sel_regmap,
> + .set_voltage_sel = regulator_set_voltage_sel_regmap,
> + .list_voltage = regulator_list_voltage_linear_range,
> + .map_voltage = regulator_map_voltage_linear_range,
> + .set_voltage_time_sel = regulator_set_voltage_time_sel,
> + .set_ramp_delay = lp87565_buck_set_ramp_delay,
> + .set_current_limit = lp87565_buck_set_current_limit,
> + .get_current_limit = lp87565_buck_get_current_limit,
> +};
> +
> +static const struct lp87565_regulator regulators[] = {
> + LP87565_REGULATOR("BUCK0", LP87565_BUCK_0, "buck0", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK0_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK0_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK0_CTRL_2),
> + LP87565_REGULATOR("BUCK1", LP87565_BUCK_1, "buck1", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK1_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK1_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK1_CTRL_2),
> + LP87565_REGULATOR("BUCK2", LP87565_BUCK_2, "buck2", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK2_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK2_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK2_CTRL_2),
> + LP87565_REGULATOR("BUCK3", LP87565_BUCK_3, "buck3", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK3_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK3_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK3_CTRL_2),
> + LP87565_REGULATOR("BUCK10", LP87565_BUCK_10, "buck10", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK0_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK0_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK0_CTRL_2),
> + LP87565_REGULATOR("BUCK23", LP87565_BUCK_23, "buck23", lp87565_buck_ops,
> + 256, LP87565_REG_BUCK2_VOUT, LP87565_BUCK_VSET,
> + LP87565_REG_BUCK2_CTRL_1,
> + LP87565_BUCK_CTRL_1_EN, 3800,
> + buck0_1_2_3_ranges, LP87565_REG_BUCK2_CTRL_2),
> +};
> +
> +static int lp87565_regulator_probe(struct platform_device *pdev)
> +{
> + struct lp87565 *lp87565 = dev_get_drvdata(pdev->dev.parent);
> + struct regulator_config config = { };
> + struct regulator_dev *rdev;
> + int i, min_idx = LP87565_BUCK_1, max_idx = LP87565_BUCK_3;
> +
> + platform_set_drvdata(pdev, lp87565);
> +
> + config.dev = &pdev->dev;
> + config.dev->of_node = lp87565->dev->of_node;
> + config.driver_data = lp87565;
> + config.regmap = lp87565->regmap;
> +
> + if (lp87565->dev_type == LP87565_DEVICE_TYPE_LP87565_Q1) {
> + min_idx = LP87565_BUCK_10;
> + max_idx = LP87565_BUCK_23;
> + }
> +
> + for (i = min_idx; i <= max_idx; i++) {
> + rdev = devm_regulator_register(&pdev->dev, ®ulators[i].desc,
> + &config);
> + if (IS_ERR(rdev)) {
> + dev_err(lp87565->dev, "failed to register %s regulator\n",
> + pdev->name);
> + return PTR_ERR(rdev);
> + }
> + }
> +
> + return 0;
> +}
> +
> +static const struct platform_device_id lp87565_regulator_id_table[] = {
> + { "lp87565-regulator", },
> + { "lp87565-q1-regulator", },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(platform, lp87565_regulator_id_table);
> +
> +static struct platform_driver lp87565_regulator_driver = {
> + .driver = {
> + .name = "lp87565-pmic",
> + },
> + .probe = lp87565_regulator_probe,
> + .id_table = lp87565_regulator_id_table,
> +};
> +module_platform_driver(lp87565_regulator_driver);
> +
> +MODULE_AUTHOR("J Keerthy <j-keerthy@xxxxxx>");
> +MODULE_DESCRIPTION("LP87565 voltage regulator driver");
> +MODULE_ALIAS("platform:lp87565-pmic");
Is this needed? This name is not used, and the above MODULE_DEVICE_TABLE
should take care of the needed aliases.
> +MODULE_LICENSE("GPL v2");
>