Re: [linux-sunxi] Re: [RFC PATCH 07/11] drm: sun4i: add support for the TV encoder in H3 SoC

[Jernej Åkrabec]

Hi,

Dne sreda, 24. maj 2017 ob 10:25:46 CEST je Icenowy Zheng napisal(a):
> ä 2017å5æ24æ GMT+08:00 äå3:30:19, Maxime Ripard <maxime.ripard@free-
electrons.com> åå:
> >On Tue, May 23, 2017 at 09:00:59PM +0800, icenowy@xxxxxxx wrote:
> >> å 2017-05-23 20:53ïMaxime Ripard åéï
> >> 
> >> > On Mon, May 22, 2017 at 07:55:56PM +0200, Jernej Åkrabec wrote:
> >> > > Hi,
> >> > > 
> >> > > Dne sobota, 20. maj 2017 ob 03:37:53 CEST je Chen-Yu Tsai
> >
> >napisal(a):
> >> > > > On Sat, May 20, 2017 at 2:23 AM, Jernej Åkrabec
> >
> ><jernej.skrabec@xxxxxxxx>
> >
> >> > > wrote:
> >> > > > > Hi,
> >> > > > > 
> >> > > > > Dne petek, 19. maj 2017 ob 20:08:18 CEST je Icenowy Zheng
> >
> >napisal(a):
> >> > > > >> ä 2017å5æ20æ GMT+08:00 äå2:03:30, Maxime Ripard
> >
> ><maxime.ripard@free-
> >
> >> > > > > electrons.com> åå:
> >> > > > >> >On Thu, May 18, 2017 at 12:43:50AM +0800, Icenowy Zheng
> >
> >wrote:
> >> > > > >> >> Allwinner H3 features a TV encoder similar to the one in
> >
> >earlier
> >
> >> > > > >> >SoCs,
> >> > > > >> >
> >> > > > >> >> but with some different points about clocks:
> >> > > > >> >> - It has a mod clock and a bus clock.
> >> > > > >> >> - The mod clock must be at a fixed rate to generate
> >
> >signal.
> >
> >> > > > >> >Why?
> >> > > > >> 
> >> > > > >> It's experiment result by Jernej.
> >> > > > >> 
> >> > > > >> The clock rates in BSP kernel is also specially designed
> >> > > > >> (PLL_DE at 432MHz) in order to be able to feed the TVE.
> >> > > > > 
> >> > > > > My experiments and search through BSP code showed that TVE
> >
> >seems to have
> >
> >> > > > > additional fixed predivider 8. So if you want to generate 27
> >
> >MHz clock,
> >
> >> > > > > unit has to be feed with 216 MHz.
> >> > > > > 
> >> > > > > TVE has only one PLL source PLL_DE. And since 216 MHz is a
> >
> >bit low for
> >
> >> > > > > DE2,
> >> > > > > BSP defaults to 432 MHz for PLL_DE and use divider 2 to
> >
> >generate 216 MHz.
> >
> >> > > > > This clock is then divided by 8 internaly to get final 27
> >
> >MHz.
> >
> >> > > > > Please note that I don't have any hard evidence to support
> >
> >that, only
> >
> >> > > > > experimental data. However, only that explanation make sense
> >
> >to me.
> >
> >> > > > > BTW, BSP H3/H5 TV driver supports only PAL and NTSC which
> >
> >both use 27 MHz
> >
> >> > > > > base clock. Further experiments are needed to check if there
> >
> >is any
> >
> >> > > > > possibility to have other resolutions by manipulating clocks
> >
> >and give
> >
> >> > > > > other proper settings. I plan to do that, but not in very
> >
> >near future.
> >
> >> > > > You only have composite video output, and those are the only 2
> >
> >standard
> >
> >> > > > resolutions that make any sense.
> >> > > 
> >> > > Right, other resolutions are for VGA.
> >> > > 
> >> > > Anyway, I did some more digging in A10 and R40 datasheets. I
> >
> >think
> >
> >> > > that H3 TVE
> >> > > unit is something in between. R40 TVE has a setting to select "up
> >> > > sample".
> >> > 
> >> > That might be just another translation of oversampling :)
> >> > 
> >> > I didn't know it could be applied to composite signals though, but
> >
> >I
> >
> >> > guess this is just another analog signal after all.
> >> > 
> >> > > Possible settings are 27 MHz, 54 MHz, 108 MHz and 216 MHz. BSP
> >> > > driver on R40
> >> > > has this setting enabled only for PAL and NTSC and it is always
> >
> >216
> >
> >> > > MHz. I
> >> > > think that H3 may have this hardwired to 216 MHz and this would
> >
> >be
> >
> >> > > the reason
> >> > > why 216 MHz is needed.
> >> > > 
> >> > > Has anyone else any better explanation?
> >> > 
> >> > That's already a pretty good one.
> >> > 
> >> > Either way, wether this is upsampling, oversampling or just a
> >> > pre-divider, this can and should be dealt with in the mode_set
> >> > callback, and not in the probe.
> >> 
> >> I got a better idea -- let TVE driver have the CLK_TVE as an
> >> input and create a subclock output with divider 16, and feed this
> >> subclock to TCON lcd-ch1.
> >> 
> >> This is a model of the real hardware -- the clock divider is in
> >> TVE, not TCON.

If we are talking about HW divider, it is 8 (216 / 27 = 8).

Slightly offtopic, reason why DE2 is hardcoded to 432 might be that for 4K 
resolution you need at least 297 MHz. So next dividable frequency is taken 
(432 MHz). That way you can have 4K HDMI display and composite TV connected at 
the same time, although this sounds a bit weird.

Best regards,
Jernej

> >
> >That's definitely not a good representation of the hardware. There's
> >one clock, it goes to the TCON, period.
> 
> No, I still think it goes to the TVE as:
> 
> 1. it's named TVE in datasheet.
> 2. Generating signal with such a low resolution but such
> a high dotclock is not a good situation.
> 
> >However, the TV encoder has a constraint on that clock rate. This can
> >be easily implemented using a custom encoder state where you'd set the
> >multiplier to set on that clock, and the TCON will use it.
> >
> >Maxime