[PATCH v4 9/9] serial: exar: Add support for IOT2040 device
From: Jan Kiszka
Date: Tue May 30 2017 - 03:02:15 EST
This implements the setup of RS232 and the switch-over to RS485 or RS422
for the Siemens IOT2040. That uses an EXAR XR17V352 with external logic
to switch between the different modes. The external logic is controlled
via MPIO pins of the EXAR controller.
Only pin 10 can be exported as GPIO on the IOT2040. It is connected to
an LED.
As the XR17V352 used on the IOT2040 is not equipped with an external
EEPROM, it cannot present itself as IOT2040-variant via subvendor/
subdevice IDs. Thus, we have to check via DMI for the target platform.
Co-developed with Sascha Weisenberger.
Signed-off-by: Sascha Weisenberger <sascha.weisenberger@xxxxxxxxxxx>
Signed-off-by: Jan Kiszka <jan.kiszka@xxxxxxxxxxx>
---
drivers/tty/serial/8250/8250_exar.c | 154 ++++++++++++++++++++++++++++++++++--
1 file changed, 148 insertions(+), 6 deletions(-)
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
index 1cdf125ffe30..25b138f43100 100644
--- a/drivers/tty/serial/8250/8250_exar.c
+++ b/drivers/tty/serial/8250/8250_exar.c
@@ -10,6 +10,7 @@
* the Free Software Foundation; either version 2 of the License.
*/
#include <linux/acpi.h>
+#include <linux/dmi.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
@@ -62,8 +63,50 @@
#define UART_EXAR_MPIOSEL_15_8 0x99 /* MPIOSEL[15:8] */
#define UART_EXAR_MPIOOD_15_8 0x9a /* MPIOOD[15:8] */
+#define UART_EXAR_RS485_DLY(x) ((x) << 4)
+
+/*
+ * IOT2040 MPIO wiring semantics:
+ *
+ * MPIO Port Function
+ * ---- ---- --------
+ * 0 2 Mode bit 0
+ * 1 2 Mode bit 1
+ * 2 2 Terminate bus
+ * 3 - <reserved>
+ * 4 3 Mode bit 0
+ * 5 3 Mode bit 1
+ * 6 3 Terminate bus
+ * 7 - <reserved>
+ * 8 2 Enable
+ * 9 3 Enable
+ * 10 - Red LED
+ * 11..15 - <unused>
+ */
+
+/* IOT2040 MPIOs 0..7 */
+#define IOT2040_UART_MODE_RS232 0x01
+#define IOT2040_UART_MODE_RS485 0x02
+#define IOT2040_UART_MODE_RS422 0x03
+#define IOT2040_UART_TERMINATE_BUS 0x04
+
+#define IOT2040_UART1_MASK 0x0f
+#define IOT2040_UART2_SHIFT 4
+
+#define IOT2040_UARTS_DEFAULT_MODE 0x11 /* both RS232 */
+#define IOT2040_UARTS_GPIO_LO_MODE 0x88 /* reserved pins as input */
+
+/* IOT2040 MPIOs 8..15 */
+#define IOT2040_UARTS_ENABLE 0x03
+#define IOT2040_UARTS_GPIO_HI_MODE 0xF8 /* enable & LED as outputs */
+
struct exar8250;
+struct exar8250_platform {
+ int (*rs485_config)(struct uart_port *, struct serial_rs485 *);
+ int (*register_gpio)(struct pci_dev *, struct uart_8250_port *);
+};
+
/**
* struct exar8250_board - board information
* @num_ports: number of serial ports
@@ -197,8 +240,8 @@ static void setup_gpio(struct pci_dev *pcidev, u8 __iomem *p)
}
static void *
-xr17v35x_register_gpio(struct pci_dev *pcidev, unsigned int first_pin,
- unsigned int ngpios)
+__xr17v35x_register_gpio(struct pci_dev *pcidev, unsigned int first_pin,
+ unsigned int ngpios)
{
struct property_entry properties[] = {
PROPERTY_ENTRY_U32("gpio-exar,first-pin", first_pin),
@@ -223,17 +266,118 @@ xr17v35x_register_gpio(struct pci_dev *pcidev, unsigned int first_pin,
return pdev;
}
+static int xr17v35x_register_gpio(struct pci_dev *pcidev,
+ struct uart_8250_port *port)
+{
+ if (pcidev->vendor == PCI_VENDOR_ID_EXAR)
+ port->port.private_data =
+ __xr17v35x_register_gpio(pcidev, 0, 16);
+
+ return 0;
+}
+
+static int iot2040_rs485_config(struct uart_port *port,
+ struct serial_rs485 *rs485)
+{
+ bool is_rs485 = !!(rs485->flags & SER_RS485_ENABLED);
+ u8 __iomem *p = port->membase;
+ u8 mask = IOT2040_UART1_MASK;
+ u8 mode, value;
+
+ if (is_rs485) {
+ if (rs485->flags & SER_RS485_RX_DURING_TX)
+ mode = IOT2040_UART_MODE_RS422;
+ else
+ mode = IOT2040_UART_MODE_RS485;
+
+ if (rs485->flags & SER_RS485_TERMINATE_BUS)
+ mode |= IOT2040_UART_TERMINATE_BUS;
+ } else {
+ mode = IOT2040_UART_MODE_RS232;
+ }
+
+ if (port->line == 3) {
+ mask <<= IOT2040_UART2_SHIFT;
+ mode <<= IOT2040_UART2_SHIFT;
+ }
+
+ value = readb(p + UART_EXAR_MPIOLVL_7_0);
+ value &= ~mask;
+ value |= mode;
+ writeb(value, p + UART_EXAR_MPIOLVL_7_0);
+
+ value = readb(p + UART_EXAR_FCTR);
+ if (is_rs485)
+ value |= UART_FCTR_EXAR_485;
+ else
+ value &= ~UART_FCTR_EXAR_485;
+ writeb(value, p + UART_EXAR_FCTR);
+
+ if (is_rs485)
+ writeb(UART_EXAR_RS485_DLY(4), p + UART_MSR);
+
+ port->rs485 = *rs485;
+
+ return 0;
+}
+
+static int iot2040_register_gpio(struct pci_dev *pcidev,
+ struct uart_8250_port *port)
+{
+ u8 __iomem *p = port->port.membase;
+
+ writeb(IOT2040_UARTS_DEFAULT_MODE, p + UART_EXAR_MPIOLVL_7_0);
+ writeb(IOT2040_UARTS_GPIO_LO_MODE, p + UART_EXAR_MPIOSEL_7_0);
+ writeb(IOT2040_UARTS_ENABLE, p + UART_EXAR_MPIOLVL_15_8);
+ writeb(IOT2040_UARTS_GPIO_HI_MODE, p + UART_EXAR_MPIOSEL_15_8);
+
+ port->port.private_data = __xr17v35x_register_gpio(pcidev, 10, 1);
+
+ return 0;
+}
+
+static const struct exar8250_platform exar8250_default_platform = {
+ .register_gpio = xr17v35x_register_gpio,
+};
+
+static const struct exar8250_platform iot2040_platform = {
+ .rs485_config = iot2040_rs485_config,
+ .register_gpio = iot2040_register_gpio,
+};
+
+static const struct dmi_system_id exar_platforms[] = {
+ {
+ .matches = {
+ DMI_EXACT_MATCH(DMI_BOARD_NAME, "SIMATIC IOT2000"),
+ DMI_EXACT_MATCH(DMI_BOARD_ASSET_TAG,
+ "6ES7647-0AA00-1YA2"),
+ },
+ .driver_data = (void *)&iot2040_platform,
+ },
+ {}
+};
+
static int
pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
struct uart_8250_port *port, int idx)
{
const struct exar8250_board *board = priv->board;
+ const struct exar8250_platform *platform;
+ const struct dmi_system_id *dmi_match;
unsigned int offset = idx * 0x400;
unsigned int baud = 7812500;
u8 __iomem *p;
int ret;
+ dmi_match = dmi_first_match(exar_platforms);
+ if (dmi_match)
+ platform = dmi_match->driver_data;
+ else
+ platform = &exar8250_default_platform;
+
port->port.uartclk = baud * 16;
+ port->port.rs485_config = platform->rs485_config;
+
/*
* Setup the uart clock for the devices on expansion slot to
* half the clock speed of the main chip (which is 125MHz)
@@ -256,12 +400,10 @@ pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev,
/* Setup Multipurpose Input/Output pins. */
setup_gpio(pcidev, p);
- if (pcidev->vendor == PCI_VENDOR_ID_EXAR)
- port->port.private_data =
- xr17v35x_register_gpio(pcidev, 0, 16);
+ ret = platform->register_gpio(pcidev, port);
}
- return 0;
+ return ret;
}
static void pci_xr17v35x_exit(struct pci_dev *pcidev)
--
2.12.3