[PATCH v6 3/3] watchdog: introduce CONFIG_WATCHDOG_OPEN_TIMEOUT

[Rasmus Villemoes]

This allows setting a default value for the watchdog.open_timeout
commandline parameter via Kconfig.

Some BSPs allow remote updating of the kernel image and root file
system, but updating the bootloader requires physical access. Hence, if
one has a firmware update that requires relaxing the
watchdog.open_timeout a little, the value used must be baked into the
kernel image itself and cannot come from the u-boot environment via the
kernel command line.

Being able to set the initial value in .config doesn't change the fact
that the value on the command line, if present, takes precedence, and is
of course immensely useful for development purposes while one has
console acccess, as well as usable in the cases where one can make a
permanent update of the kernel command line.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@xxxxxxxxx>
---
 Documentation/watchdog/watchdog-parameters.txt | 3 ++-
 drivers/watchdog/Kconfig                       | 9 +++++++++
 drivers/watchdog/watchdog_dev.c                | 2 +-
 3 files changed, 12 insertions(+), 2 deletions(-)

diff --git a/Documentation/watchdog/watchdog-parameters.txt b/Documentation/watchdog/watchdog-parameters.txt
index 8577c27..fa34625 100644
--- a/Documentation/watchdog/watchdog-parameters.txt
+++ b/Documentation/watchdog/watchdog-parameters.txt
@@ -11,7 +11,8 @@ modules.
 The watchdog core parameter watchdog.open_timeout is the maximum time,
 in milliseconds, for which the watchdog framework will take care of
 pinging a hardware watchdog until userspace opens the corresponding
-/dev/watchdogN device. A value of 0 (the default) means an infinite
+/dev/watchdogN device. The defalt value is
+CONFIG_WATCHDOG_OPEN_TIMEOUT. A value of 0 means an infinite
 timeout. Setting this to a non-zero value can be useful to ensure that
 either userspace comes up properly, or the board gets reset and allows
 fallback logic in the bootloader to try something else.
diff --git a/drivers/watchdog/Kconfig b/drivers/watchdog/Kconfig
index 8b9049d..11946fb 100644
--- a/drivers/watchdog/Kconfig
+++ b/drivers/watchdog/Kconfig
@@ -52,6 +52,15 @@ config WATCHDOG_SYSFS
 	  Say Y here if you want to enable watchdog device status read through
 	  sysfs attributes.
 
+config WATCHDOG_OPEN_TIMEOUT
+	int "Timeout value for opening watchdog device"
+	default 0
+	help
+	  The maximum time, in milliseconds, for which the watchdog
+	  framework takes care of pinging a hardware watchdog. A value
+	  of 0 means infinite. The value set here can be overridden by
+	  the commandline parameter "watchdog.open_timeout".
+
 #
 # General Watchdog drivers
 #
diff --git a/drivers/watchdog/watchdog_dev.c b/drivers/watchdog/watchdog_dev.c
index c807067..098b9cb 100644
--- a/drivers/watchdog/watchdog_dev.c
+++ b/drivers/watchdog/watchdog_dev.c
@@ -81,7 +81,7 @@ static struct watchdog_core_data *old_wd_data;
 
 static struct workqueue_struct *watchdog_wq;
 
-static unsigned open_timeout;
+static unsigned open_timeout = CONFIG_WATCHDOG_OPEN_TIMEOUT;
 module_param(open_timeout, uint, 0644);
 
 static bool watchdog_past_open_deadline(struct watchdog_core_data *data)
-- 
2.7.4