[PATCH v4 1/1] ARM: dts: imx53: Add GE Healthcare PPD

From: Martyn Welch
Date: Tue Jul 11 2017 - 09:43:18 EST

From: Fabien Lahoudere <fabien.lahoudere@xxxxxxxxxxxxxxx>

PPD is a product from GE Healthcare to monitor vital biometric signals.

Signed-off-by: Fabien Lahoudere <fabien.lahoudere@xxxxxxxxxxxxxxx>
Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
Signed-off-by: Martyn Welch <martyn.welch@xxxxxxxxxxxxxxx>
---

Changes since PATCHv3: https://patchwork.kernel.org/patch/9819017/
- licensing modified
- manufacturer changed to GE
- regulator nodes corrected
- backlight node corrected
- flags rather than magic numbers used
- registers for usbphys added
- set up IOMUX configuration correctly
- various whitespace corrections
- removed unused fsl,mode node
- missing unit addresses added
- reordered nodes and properties as requested
Changes since PATCHv2: https://patchwork.kernel.org/patch/9809681/
- drop dma-info property from serial nodes. That property is not
available in mainline.
Changes since PATCHv1: https://patchwork.kernel.org/patch/9265391/
- fixed issues raised by Mark
- added some missing vendor prefixes
- dropped anx9804 nodes (no upstream support/binding)
- use proper chip-select for ecspi1.cs0

arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx53-ppd.dts | 1059 +++++++++++++++++++++++++++++++++++++++
2 files changed, 1060 insertions(+)
create mode 100644 arch/arm/boot/dts/imx53-ppd.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9c5e1d9..135ae56 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -340,6 +340,7 @@ dtb-$(CONFIG_SOC_IMX53) += \
imx53-ard.dtb \
imx53-m53evk.dtb \
imx53-mba53.dtb \
+ imx53-ppd.dtb \
imx53-qsb.dtb \
imx53-qsrb.dtb \
imx53-smd.dtb \
diff --git a/arch/arm/boot/dts/imx53-ppd.dts b/arch/arm/boot/dts/imx53-ppd.dts
new file mode 100644
index 0000000..0480fa9
--- /dev/null
+++ b/arch/arm/boot/dts/imx53-ppd.dts
@@ -0,0 +1,1059 @@
+/*
+ * Copyright 2014 General Electric Company
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx53.dtsi"
+
+/ {
+ model = "Freescale i.MX53 CPUV0 PPD rev6";
+ compatible = "ge,imx53-cpuvo", "fsl,imx53";
+
+ aliases {
+ spi0 = &cspi;
+ spi1 = &ecspi1;
+ spi2 = &ecspi2;
+ };
+
+ chosen {
+ stdout-path = "&uart1:115200n8";
+ };
+
+ memory@70000000 {
+ device_type = "memory";
+ reg = <0x70000000 0x20000000>,
+ <0xb0000000 0x20000000>;
+ };
+
+ cko2_11M: sgtl_clock_cko2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <11289600>;
+ };
+
+ sgtlsound: sound {
+ compatible = "fsl,imx53-cpuvo-sgtl5000",
+ "fsl,imx-audio-sgtl5000";
+ model = "imx53-cpuvo-sgtl5000";
+ ssi-controller = <&ssi2>;
+ audio-codec = <&sgtl5000>;
+ audio-routing =
+ "MIC_IN", "Mic Jack",
+ "Mic Jack", "Mic Bias",
+ "Headphone Jack", "HP_OUT";
+ mux-int-port = <2>;
+ mux-ext-port = <6>;
+ status = "okay";
+ };
+
+ reg_sgtl5k: regulator-sgtl5k {
+ compatible = "regulator-fixed";
+ regulator-name = "regulator-sgtl5k";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbotg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-0 = <&pinctrl_usb_otg_vbus>;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_vbus: regulator-usb-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usbh2_vbus: regulator-usbh2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2_vbus>;
+ gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usbh3_vbus: regulator-usbh3-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usbh3_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh3_vbus>;
+ gpio = <&gpio5 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ backlight: pwm-bl {
+ compatible = "pwm-backlight";
+ pwms = <&pwm2 0 50000>;
+ brightness-levels = <0 2 5 7 10 12 15 17 20 22 25 28 30 33 35 \
+ 38 40 43 45 48 51 53 56 58 61 63 66 68 71 \
+ 73 76 79 81 84 86 89 91 94 96 99 102 104 \
+ 107 109 112 114 117 119 122 124 127 130 \
+ 132 135 137 140 142 145 147 150 153 155 \
+ 158 160 163 165 168 170 173 175 178 181 \
+ 183 186 188 191 193 196 198 201 204 206 \
+ 209 211 214 216 219 221 224 226 229 232 \
+ 234 237 239 242 244 247 249 252 255>;
+ default-brightness-level = <0>;
+ enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ leds {
+ compatible = "pwm-leds";
+
+ alarm-brightness {
+ pwms = <&pwm1 0 100000>;
+ max-brightness = <255>;
+ };
+ };
+
+ gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+ };
+
+ gpio-restart {
+ compatible = "gpio-restart";
+ gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+ active-delay = <100>;
+ inactive-delay = <10>;
+ wait-delay = <100>;
+ };
+
+ power-gpio-keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ power-button {
+ label = "Power button";
+ gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+ linux,code = <116>;
+ };
+ };
+
+ touch-lock-key {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ touch-lock-button {
+ label = "Touch lock button";
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ linux,code = <88>;
+ };
+ };
+
+ usbphy2: usbphy@2 {
+ reg = <2>;
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>;
+ clock-names = "main_clk";
+
+ clock-frequency = <24000000>;
+ clocks = <&clks IMX5_CLK_CKO2>;
+ assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
+ assigned-clock-parents = <&clks IMX5_CLK_OSC>;
+ status = "okay";
+ };
+
+ usbphy3: usbphy@3 {
+ reg = <3>;
+ compatible = "usb-nop-xceiv";
+ reset-gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
+ clock-names = "main_clk";
+
+ clock-frequency = <24000000>;
+ clocks = <&clks IMX5_CLK_CKO2>;
+ assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks IMX5_CLK_OSC>;
+ assigned-clock-parents = <&clks IMX5_CLK_OSC>;
+ status = "okay";
+ };
+
+ panel-lvds0 {
+ compatible = "nvd,9128";
+
+ port {
+ panel_in_lvds0: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&ecspi1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ fsl,spi-num-chipselects = <4>;
+ cs-gpios = <&gpio5 17 GPIO_ACTIVE_LOW
+ &gpio4 10 GPIO_ACTIVE_LOW
+ &gpio4 11 GPIO_ACTIVE_LOW
+ &gpio4 12 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ spidev0: spi@0 {
+ compatible = "ge,achc";
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ status = "okay";
+ };
+
+ spidev1: spi@1 {
+ compatible = "ge,achc";
+ reg = <1>;
+ spi-max-frequency = <1000000>;
+ status = "okay";
+ };
+
+ gpioxra0: gpio@2 {
+ compatible = "exar,xra1403";
+ reg = <2>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ spi-max-frequency = <1000000>;
+ status = "okay";
+ };
+
+ gpioxra1: gpio@3 {
+ compatible = "exar,xra1403";
+ reg = <3>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ spi-max-frequency = <1000000>;
+ status = "okay";
+ };
+};
+
+&ecspi2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ fsl,spi-num-chipselects = <1>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ da9053@0 {
+ compatible = "dlg,da9053-aa";
+ reg = <0>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <12 0x8>;
+ spi-max-frequency = <1000000>;
+ status = "okay";
+
+ regulators {
+ buck1_reg: buck1 {
+ regulator-name = "BUCKCORE";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: buck2 {
+ regulator-name = "BUCKPRO";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2075000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: buck3 {
+ regulator-name = "BUCKMEM";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: buck4 {
+ regulator-name = "BUCKPERI";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-name = "ldo1_1v3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "ldo2_1v3";
+ regulator-min-microvolt = <600000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-name = "ldo3_3v3";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-name = "ldo4_2v775";
+ regulator-min-microvolt = <1725000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ regulator-name = "ldo5_3v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: ldo6 {
+ regulator-name = "ldo6_1v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: ldo7 {
+ regulator-name = "ldo7_2v75";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: ldo8 {
+ regulator-name = "ldo8_1v8";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: ldo9 {
+ regulator-name = "ldo9_1v5";
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <3650000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: ldo10 {
+ regulator-name = "ldo10_1v3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <3600000>;
+ regulator-always-on;
+ };
+ };
+ };
+
+};
+
+&esdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc1>;
+ status = "disabled";
+};
+
+&esdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_esdhc3>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fec>;
+ phy-mode = "rmii";
+ phy-reset-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ pinctrl-1 = <&pinctrl_i2c1_gpio>;
+ sda-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ i2xmux_pca: i2c-mux_pca954x@70 {
+ compatible = "nxp,pca9547";
+ reg = <0x70>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
+
+ i2c4: i2cmux-ppd@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ sgtl5000: codec@0a {
+ compatible = "fsl,sgtl5000";
+ reg = <0x0a>;
+ VDDA-supply = <&reg_sgtl5k>;
+ VDDIO-supply = <&reg_sgtl5k>;
+ clocks = <&cko2_11M>;
+ status = "okay";
+ };
+ };
+
+ i2c5: i2cmux-ppd@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ rtc@30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+
+ tmp112@48 {
+ compatible = "ti,tmp112";
+ reg = <0x48>;
+ };
+
+ mma8453q@1c {
+ compatible = "fsl,mma8453";
+ reg = <0x1c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <6 0>;
+ interrupt-names = "INT1";
+ };
+
+ mpl3115: mpl3115@60 {
+ compatible = "fsl,mpl3115";
+ reg = <0x60>;
+ };
+
+ eeprom: eeprom@50 {
+ compatible = "atmel,24c08";
+ reg = <0x50>;
+ };
+ };
+
+ i2c6: i2cmux-ppd@2 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <2>;
+ };
+
+ i2c7: i2cmux-ppd@3 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <3>;
+ };
+
+ i2c8: i2cmux-ppd@4 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4>;
+ };
+
+ i2c9: i2cmux-ppd@5 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <5>;
+ };
+
+ i2c10: i2cmux-ppd@6 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <6>;
+ };
+
+ i2c11: i2cmux-ppd@7 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <7>;
+ };
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ pinctrl-1 = <&pinctrl_i2c2_gpio>;
+ sda-gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ touchscreen@4b {
+ compatible = "atmel,maxtouch";
+ reg = <0x4b>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <4 0x8>;
+ };
+};
+
+&i2c3 {
+ pinctrl-names = "default", "gpio";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ pinctrl-1 = <&pinctrl_i2c3_gpio>;
+ sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
+ scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds0: lvds-channel@0 {
+ status = "okay";
+
+ port@2 {
+ reg = <2>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in_lvds0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>;
+ status = "okay";
+};
+
+&ssi2 {
+ fsl,mode = "i2s-slave";
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "otg";
+ phy_type = "utmi";
+ vbus-supply = <&reg_usb_otg_vbus>;
+ pinctrl-0 = <&pinctrl_usb_otg>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <&reg_usb_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbh2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh2>;
+ phy_type = "ulpi";
+ disable-int60ck;
+ dr_mode = "host";
+ fsl,usbphy = <&usbphy2>;
+ vbus-supply = <&reg_usbh2_vbus>;
+ status = "okay";
+};
+
+&usbh3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbh3>;
+ phy_type = "ulpi";
+ disable-int60ck;
+ dr_mode = "host";
+ vbus-supply = <&reg_usbh3_vbus>;
+ fsl,usbphy = <&usbphy3>;
+ status = "okay";
+};
+
+/* Pin configuration variables */
+#define NO_PAD_CTL 0x00010000
+#define PAD_CTL_DEFAULT 0x00e4
+#define PAD_CTL_5 0x0005
+#define PAD_CTL_7 0x0180
+#define I2C_PAD_CTL 0xc0000000
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog_rev6>;
+ imx53-cpuvo {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT19__AUDMUX_AUD5_RXD NO_PAD_CTL
+ MX53_PAD_DISP0_DAT17__AUDMUX_AUD5_TXD NO_PAD_CTL
+ MX53_PAD_DISP0_DAT16__AUDMUX_AUD5_TXC NO_PAD_CTL
+ MX53_PAD_DISP0_DAT18__AUDMUX_AUD5_TXFS NO_PAD_CTL
+ MX53_PAD_DI0_PIN15__AUDMUX_AUD6_TXC NO_PAD_CTL
+ MX53_PAD_DI0_PIN3__AUDMUX_AUD6_TXFS NO_PAD_CTL
+ MX53_PAD_DI0_PIN4__AUDMUX_AUD6_RXD NO_PAD_CTL
+ MX53_PAD_DI0_PIN2__AUDMUX_AUD6_TXD NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT21__ECSPI1_MOSI NO_PAD_CTL
+ MX53_PAD_DISP0_DAT22__ECSPI1_MISO NO_PAD_CTL
+ MX53_PAD_DISP0_DAT20__ECSPI1_SCLK NO_PAD_CTL
+ /* ECSPI1_SS0, must treat as GPIO for EzPort */
+ MX53_PAD_DISP0_DAT23__GPIO5_17 NO_PAD_CTL
+ MX53_PAD_KEY_COL2__GPIO4_10 NO_PAD_CTL
+ MX53_PAD_KEY_ROW2__GPIO4_11 NO_PAD_CTL
+ MX53_PAD_KEY_COL3__GPIO4_12 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX53_PAD_EIM_CS1__ECSPI2_MOSI NO_PAD_CTL
+ MX53_PAD_EIM_OE__ECSPI2_MISO NO_PAD_CTL
+ MX53_PAD_EIM_CS0__ECSPI2_SCLK NO_PAD_CTL
+ MX53_PAD_EIM_RW__GPIO2_26 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_esdhc1: esdhc1grp {
+ fsl,pins = <
+ MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5
+ MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5
+ MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5
+ MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5
+ MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5
+ MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_esdhc3: esdhc3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5
+ MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5
+ MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5
+ MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5
+ MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5
+ MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5
+ MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5
+ MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5
+ MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5
+ MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5
+ >;
+ };
+
+ pinctrl_fec: fecgrp {
+ fsl,pins = <
+ MX53_PAD_FEC_MDC__FEC_MDC NO_PAD_CTL
+ MX53_PAD_FEC_MDIO__FEC_MDIO NO_PAD_CTL
+ MX53_PAD_FEC_REF_CLK__FEC_TX_CLK NO_PAD_CTL
+ MX53_PAD_FEC_RX_ER__FEC_RX_ER NO_PAD_CTL
+ MX53_PAD_FEC_CRS_DV__FEC_RX_DV NO_PAD_CTL
+ MX53_PAD_FEC_RXD1__FEC_RDATA_1 NO_PAD_CTL
+ MX53_PAD_FEC_RXD0__FEC_RDATA_0 NO_PAD_CTL
+ MX53_PAD_FEC_TX_EN__FEC_TX_EN NO_PAD_CTL
+ MX53_PAD_FEC_TXD1__FEC_TDATA_1 NO_PAD_CTL
+ MX53_PAD_FEC_TXD0__FEC_TDATA_0 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_hog_rev6: hoggrp_rev6 {
+ fsl,pins = <
+ /* CKO2 */
+ MX53_PAD_GPIO_3__CCM_CLKO2 0x0004
+ /* DEFIB_SYNC_MARKER_IN_IRQ */
+ MX53_PAD_GPIO_5__GPIO1_5 NO_PAD_CTL
+ /* ACCELEROMETER_DATA_RDY_N */
+ MX53_PAD_GPIO_6__GPIO1_6 NO_PAD_CTL
+ /* TEMPERATURE_ALERT_N */
+ MX53_PAD_GPIO_7__GPIO1_7 NO_PAD_CTL
+ /* BAROMETRIC_PRESSURE_DATA_RDY_N */
+ MX53_PAD_GPIO_8__GPIO1_8 NO_PAD_CTL
+ /* DOCKING_I2C_INTERFACE_IRQ_N */
+ MX53_PAD_PATA_DATA4__GPIO2_4 NO_PAD_CTL
+ /* PWR_OUT_TO_DOCK_FAULT_N */
+ MX53_PAD_PATA_DATA5__GPIO2_5 NO_PAD_CTL
+ /* ENABLE_PWR_TO_DOCK_N */
+ MX53_PAD_PATA_DATA6__GPIO2_6 NO_PAD_CTL
+ /* HOST_CONTROLLED_RESET_TO_DOCKING_CONNECTOR_N */
+ MX53_PAD_PATA_DATA7__GPIO2_7 NO_PAD_CTL
+ /* REMOTE_ON_REQUEST_FROM_DOCKING_CONNECTOR_IS_ACTIVE_N */
+ MX53_PAD_PATA_DATA12__GPIO2_12 NO_PAD_CTL
+ /* DOCK_PRESENT_N */
+ MX53_PAD_PATA_DATA13__GPIO2_13 NO_PAD_CTL
+ /* ECG_MARKER_IN_FROM_DOCKING_CONNECTOR_IRQ */
+ MX53_PAD_PATA_DATA14__GPIO2_14 NO_PAD_CTL
+ /* ENABLE_ECG_MARKER_INTERFACE_TO_DOCKING_CONNECTOR */
+ MX53_PAD_PATA_DATA15__GPIO2_15 NO_PAD_CTL
+ /* RESET_IMX535_ETHERNET_PHY_N */
+ MX53_PAD_EIM_A22__GPIO2_16 NO_PAD_CTL
+ /* ENABLE_PWR_TO_LCD_AND_UI_INTERFACE */
+ MX53_PAD_EIM_A21__GPIO2_17 NO_PAD_CTL
+ /* RESET_I2C1_BUS_SEGMENT_MUX_N */
+ MX53_PAD_EIM_A20__GPIO2_18 NO_PAD_CTL
+ /* RESET_IMX535_USB_HOST3_PHY_N */
+ MX53_PAD_EIM_A19__GPIO2_19 NO_PAD_CTL
+ /* ESDHC3_EMMC_NAND_RST_N */
+ MX53_PAD_EIM_A18__GPIO2_20 NO_PAD_CTL
+ /* LCD_AND_UI_INTERFACE_PWR_FAULT_N */
+ MX53_PAD_EIM_A17__GPIO2_21 NO_PAD_CTL
+ /* POWER_DOWN_LVDS0_DESERIALIZER_N */
+ MX53_PAD_EIM_A16__GPIO2_22 NO_PAD_CTL
+ /* POWER_DOWN_LVDS1_DESERIALIZER_N */
+ MX53_PAD_EIM_LBA__GPIO2_27 NO_PAD_CTL
+ /* RESET_DP0_TRANSMITTER_N */
+ MX53_PAD_EIM_EB0__GPIO2_28 NO_PAD_CTL
+ /* RESET_DP1_TRANSMITTER_N */
+ MX53_PAD_EIM_EB1__GPIO2_29 NO_PAD_CTL
+ /* ENABLE_SPDIF_AUDIO_TO_DP0 */
+ MX53_PAD_EIM_DA0__GPIO3_0 NO_PAD_CTL
+ /* ENABLE_SPDIF_AUDIO_TO_DP1 */
+ MX53_PAD_EIM_DA1__GPIO3_1 NO_PAD_CTL
+ /* LVDS1_MUX_CTRL */
+ MX53_PAD_EIM_DA2__GPIO3_2 NO_PAD_CTL
+ /* LVDS0_MUX_CTRL */
+ MX53_PAD_EIM_DA3__GPIO3_3 NO_PAD_CTL
+ /* DP1_TRANSMITTER_IRQ */
+ MX53_PAD_EIM_DA4__GPIO3_4 NO_PAD_CTL
+ /* DP0_TRANSMITTER_IRQ */
+ MX53_PAD_EIM_DA5__GPIO3_5 NO_PAD_CTL
+ /* USB_RESET_N */
+ MX53_PAD_EIM_DA6__GPIO3_6 NO_PAD_CTL
+ /* ENABLE_BATTERY_CHARGER */
+ MX53_PAD_EIM_DA7__GPIO3_7 NO_PAD_CTL
+ /* SOFTWARE_CONTROLLED_PWR_CYCLE */
+ MX53_PAD_EIM_DA8__GPIO3_8 NO_PAD_CTL
+ /* SOFTWARE_CONTROLLED_POWERDOWN */
+ MX53_PAD_EIM_DA9__GPIO3_9 NO_PAD_CTL
+ /* DC_PWR_IN_OK */
+ MX53_PAD_EIM_DA10__GPIO3_10 NO_PAD_CTL
+ /* BATT_PRESENT_N */
+ MX53_PAD_EIM_DA11__GPIO3_11 PAD_CTL_DEFAULT
+ /* PMIC_IRQ_N */
+ MX53_PAD_EIM_DA12__GPIO3_12 NO_PAD_CTL
+ /* PMIC_VDD_FAULT_STATUS_N */
+ MX53_PAD_EIM_DA13__GPIO3_13 NO_PAD_CTL
+ /* IMX535_ETHERNET_PHY_STATUS_IRQ_N */
+ MX53_PAD_EIM_DA14__GPIO3_14 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_DA15__GPIO3_15 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_D22__GPIO3_22 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 3.3V GPIO */
+ MX53_PAD_EIM_D24__GPIO3_24 NO_PAD_CTL
+ /* NBP_PUMP_VALVE_PWR_ENABLE */
+ MX53_PAD_EIM_D25__GPIO3_25 NO_PAD_CTL
+ /* NIBP_RESET_N */
+ MX53_PAD_EIM_D26__GPIO3_26 NO_PAD_CTL
+ /* LATCHED_OVERPRESSURE_N */
+ MX53_PAD_EIM_D27__GPIO3_27 NO_PAD_CTL
+ /* NBP_SBWTCLK */
+ MX53_PAD_EIM_D29__GPIO3_29 NO_PAD_CTL
+ /* ENABLE_WIFI_MODULE */
+ MX53_PAD_GPIO_11__GPIO4_1 NO_PAD_CTL
+ /* WIFI_MODULE_IRQ_N */
+ MX53_PAD_GPIO_12__GPIO4_2 NO_PAD_CTL
+ /* ENABLE_BLUETOOTH_MODULE */
+ MX53_PAD_GPIO_13__GPIO4_3 NO_PAD_CTL
+ /* RESET_IMX535_USB_HOST2_PHY_N */
+ MX53_PAD_GPIO_14__GPIO4_4 NO_PAD_CTL
+ /* ONKEY_IS_DEPRESSED */
+ MX53_PAD_KEY_ROW3__GPIO4_13 NO_PAD_CTL
+ /* UNUSED_GPIO_TO_ALARM_LIGHT_BOARD */
+ MX53_PAD_EIM_WAIT__GPIO5_0 NO_PAD_CTL
+ /* DISPLAY_LOCK_BUTTON_IS_DEPRESSED_N */
+ MX53_PAD_EIM_A25__GPIO5_2 NO_PAD_CTL
+ /* I2C_PCAP_TOUCHSCREEN_IRQ_N */
+ MX53_PAD_EIM_A24__GPIO5_4 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT13__GPIO5_7 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT14__GPIO5_8 NO_PAD_CTL
+ /* NOT USED - AVAILABLE 1.8V GPIO */
+ MX53_PAD_DISP0_DAT15__GPIO5_9 NO_PAD_CTL
+ /* HOST_CONTROLLED_RESET_TO_LCD_N */
+ MX53_PAD_CSI0_PIXCLK__GPIO5_18 NO_PAD_CTL
+ /* HOST_CONTROLLED_RESET_TO_PCAP_N */
+ MX53_PAD_CSI0_MCLK__GPIO5_19 NO_PAD_CTL
+ /* LR_SCAN_CTRL */
+ MX53_PAD_CSI0_DATA_EN__GPIO5_20 NO_PAD_CTL
+ /* UD_SCAN_CTRL */
+ MX53_PAD_CSI0_VSYNC__GPIO5_21 NO_PAD_CTL
+ /* DATA_WIDTH_CTRL */
+ MX53_PAD_CSI0_DAT10__GPIO5_28 NO_PAD_CTL
+ /* BACKLIGHT_ENABLE */
+ MX53_PAD_CSI0_DAT11__GPIO5_29 NO_PAD_CTL
+ /* MED_USB_PORT_1_HOST_SELECT */
+ MX53_PAD_EIM_A23__GPIO6_6 NO_PAD_CTL
+ /* MED_USB_PORT_2_HOST_SELECT */
+ MX53_PAD_NANDF_CLE__GPIO6_7 NO_PAD_CTL
+ /* MED_USB_PORT_3_HOST_SELECT */
+ MX53_PAD_NANDF_ALE__GPIO6_8 NO_PAD_CTL
+ /* MED_USB_PORT_4_HOST_SELECT */
+ MX53_PAD_NANDF_WP_B__GPIO6_9 NO_PAD_CTL
+ /* MED_USB_PORT_5_HOST_SELECT */
+ MX53_PAD_NANDF_RB0__GPIO6_10 NO_PAD_CTL
+ /* MED_USB_PORT_6_HOST_SELECT */
+ MX53_PAD_NANDF_CS0__GPIO6_11 NO_PAD_CTL
+ /* MED_USB_PORT_7_HOST_SELECT */
+ MX53_PAD_NANDF_WE_B__GPIO6_12 NO_PAD_CTL
+ /* MED_USB_PORT_8_HOST_SELECT */
+ MX53_PAD_NANDF_RE_B__GPIO6_13 NO_PAD_CTL
+ /* MED_USB_PORT_TO_IMX_SELECT_0 */
+ MX53_PAD_NANDF_CS1__GPIO6_14 NO_PAD_CTL
+ /* MED_USB_PORT_TO_IMX_SELECT_1 */
+ MX53_PAD_NANDF_CS2__GPIO6_15 NO_PAD_CTL
+ /* MED_USB_PORT_TO_IMX_SELECT_2 */
+ MX53_PAD_NANDF_CS3__GPIO6_16 NO_PAD_CTL
+ /* POWER_AND_BOOT_STATUS_INDICATOR */
+ MX53_PAD_PATA_INTRQ__GPIO7_2 NO_PAD_CTL
+ /* ACTIVATE_ALARM_LIGHT_RED */
+ MX53_PAD_PATA_DIOR__GPIO7_3 NO_PAD_CTL
+ /* ACTIVATE_ALARM_LIGHT_YELLOW */
+ MX53_PAD_PATA_DA_1__GPIO7_7 NO_PAD_CTL
+ /* ACTIVATE_ALARM_LIGHT_CYAN */
+ MX53_PAD_PATA_DA_2__GPIO7_8 NO_PAD_CTL
+ /* RUNNING_ON_BATTERY_INDICATOR_GREEN */
+ MX53_PAD_GPIO_16__GPIO7_11 NO_PAD_CTL
+ /* BATTERY_STATUS_INDICATOR_AMBER */
+ MX53_PAD_GPIO_17__GPIO7_12 NO_PAD_CTL
+ /* AUDIO_ALARMS_SILENCED_INDICATOR */
+ MX53_PAD_GPIO_18__GPIO7_13 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX53_PAD_EIM_D21__I2C1_SCL I2C_PAD_CTL
+ MX53_PAD_EIM_D28__I2C1_SDA I2C_PAD_CTL
+ >;
+ };
+
+ pinctrl_i2c1_gpio: i2c1gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D28__GPIO3_28 0x1e4
+ MX53_PAD_EIM_D21__GPIO3_21 0x1e4
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX53_PAD_EIM_EB2__I2C2_SCL I2C_PAD_CTL
+ MX53_PAD_EIM_D16__I2C2_SDA I2C_PAD_CTL
+ >;
+ };
+
+ pinctrl_i2c2_gpio: i2c2gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D16__GPIO3_16 0x1e4
+ MX53_PAD_EIM_EB2__GPIO2_30 0x1e4
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX53_PAD_EIM_D17__I2C3_SCL I2C_PAD_CTL
+ MX53_PAD_EIM_D18__I2C3_SDA I2C_PAD_CTL
+ >;
+ };
+
+ pinctrl_i2c3_gpio: i2c3gpiogrp {
+ fsl,pins = <
+ MX53_PAD_EIM_D18__GPIO3_18 0x1e4
+ MX53_PAD_EIM_D17__GPIO3_17 0x1e4
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX53_PAD_GPIO_9__PWM1_PWMO 0x5
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX53_PAD_DISP0_DAT9__PWM2_PWMO 0x5
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4
+ MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4
+ MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4
+ MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4
+ MX53_PAD_EIM_D23__UART3_CTS 0x1e4
+ MX53_PAD_EIM_EB3__UART3_RTS 0x1e4
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4
+ MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4
+ MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4
+ >;
+ };
+
+ pinctrl_usb_otg_vbus: usb-otg-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_OTG_VBUS_ENABLE */
+ MX53_PAD_KEY_ROW4__GPIO4_15 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_usbh2: usbh2grp {
+ fsl,pins = <
+ /* USB H2 */
+ MX53_PAD_DISP0_DAT0__USBOH3_USBH2_DATA_0 PAD_CTL_7
+ MX53_PAD_DISP0_DAT1__USBOH3_USBH2_DATA_1 PAD_CTL_7
+ MX53_PAD_DISP0_DAT2__USBOH3_USBH2_DATA_2 PAD_CTL_7
+ MX53_PAD_DISP0_DAT3__USBOH3_USBH2_DATA_3 PAD_CTL_7
+ MX53_PAD_DISP0_DAT4__USBOH3_USBH2_DATA_4 PAD_CTL_7
+ MX53_PAD_DISP0_DAT5__USBOH3_USBH2_DATA_5 PAD_CTL_7
+ MX53_PAD_DISP0_DAT6__USBOH3_USBH2_DATA_6 PAD_CTL_7
+ MX53_PAD_DISP0_DAT7__USBOH3_USBH2_DATA_7 PAD_CTL_7
+ MX53_PAD_DISP0_DAT10__USBOH3_USBH2_STP PAD_CTL_7
+ MX53_PAD_DISP0_DAT11__USBOH3_USBH2_NXT PAD_CTL_7
+ MX53_PAD_DISP0_DAT12__USBOH3_USBH2_CLK PAD_CTL_7
+ MX53_PAD_DI0_DISP_CLK__USBOH3_USBH2_DIR PAD_CTL_5
+ MX53_PAD_EIM_D30__USBOH3_USBH2_OC PAD_CTL_7
+ >;
+ };
+
+ pinctrl_usbh2_vbus: usbh2-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_HOST2_VBUS_ENABLE */
+ MX53_PAD_EIM_D31__GPIO3_31 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_usbh3_vbus: usbh3-vbusgrp {
+ fsl,pins = <
+ /* USB_HS_HOST3_VBUS_ENABLE */
+ MX53_PAD_CSI0_DAT9__GPIO5_27 NO_PAD_CTL
+ >;
+ };
+
+ pinctrl_usbh3: usbh3grp {
+ fsl,pins = <
+ /* USB H3 */
+ MX53_PAD_CSI0_DAT12__USBOH3_USBH3_DATA_0 PAD_CTL_7
+ MX53_PAD_CSI0_DAT13__USBOH3_USBH3_DATA_1 PAD_CTL_7
+ MX53_PAD_CSI0_DAT14__USBOH3_USBH3_DATA_2 PAD_CTL_7
+ MX53_PAD_CSI0_DAT15__USBOH3_USBH3_DATA_3 PAD_CTL_7
+ MX53_PAD_CSI0_DAT16__USBOH3_USBH3_DATA_4 PAD_CTL_7
+ MX53_PAD_CSI0_DAT17__USBOH3_USBH3_DATA_5 PAD_CTL_7
+ MX53_PAD_CSI0_DAT18__USBOH3_USBH3_DATA_6 PAD_CTL_7
+ MX53_PAD_CSI0_DAT19__USBOH3_USBH3_DATA_7 PAD_CTL_7
+ MX53_PAD_CSI0_DAT7__USBOH3_USBH3_DIR PAD_CTL_5
+ MX53_PAD_CSI0_DAT6__USBOH3_USBH3_CLK PAD_CTL_7
+ MX53_PAD_CSI0_DAT5__USBOH3_USBH3_NXT PAD_CTL_7
+ MX53_PAD_CSI0_DAT4__USBOH3_USBH3_STP PAD_CTL_7
+ MX53_PAD_CSI0_DAT8__USBOH3_USBH3_OC PAD_CTL_7
+ >;
+ };
+
+ pinctrl_usb_otg: usbotggrp {
+ fsl,pins = <
+ /* USB_OTG_FAULT_N */
+ MX53_PAD_KEY_COL4__USBOH3_USBOTG_OC PAD_CTL_7
+ >;
+ };
+ };
+};
--
1.8.3.1