[PATCH 17/18] arm: dts: sun8i: Add BananaPI M2-Magic DTS

From: Maxime Ripard
Date: Thu Jul 13 2017 - 10:14:03 EST

The Bananapi M2-Magic is a board with an A33, a USB host and USB OTG
connectors, and 8GB eMMC, an AP6212 WiFi/Bluetooth chip and connectors for
DSI, CSI and GPIOs.

Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +-
arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 321 ++++++++++++++++++++-
2 files changed, 322 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4b17f35dc9a7..e0d77ab79f5f 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -918,6 +918,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-pc-plus.dtb \
sun8i-h3-orangepi-plus.dtb \
sun8i-h3-orangepi-plus2e.dtb \
+ sun8i-r16-bananapi-m2m.dtb \
sun8i-r16-parrot.dtb \
sun8i-v3s-licheepi-zero.dtb \
sun8i-v3s-licheepi-zero-dock.dtb
diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
new file mode 100644
index 000000000000..eaf09666720d
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
@@ -0,0 +1,321 @@
+/*
+ * Copyright (c) 2017 Free Electrons <maxime.ripard@xxxxxxxxxxxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-a33.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "BananaPi M2 Magic";
+ compatible = "sinovoip,bananapi-m2m", "allwinner,sun8i-a33";
+
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ serial0 = &uart0;
+ serial1 = &uart1;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ blue {
+ label = "bpi-m2m:blue:usr";
+ gpios = <&pio 2 7 GPIO_ACTIVE_LOW>;
+ };
+
+ green {
+ label = "bpi-m2m:green:usr";
+ gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>;
+ };
+
+ red {
+ label = "bpi-m2m:red:power";
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+
+ reg_vcc5v0: vcc5v0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
+ };
+};
+
+&codec {
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <&reg_dcdc3>;
+};
+
+&cpu0_opp_table {
+ opp@1104000000 {
+ opp-hz = /bits/ 64 <1104000000>;
+ opp-microvolt = <1320000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+
+ opp@1200000000 {
+ opp-hz = /bits/ 64 <1200000000>;
+ opp-microvolt = <1320000>;
+ clock-latency-ns = <244144>; /* 8 32k periods */
+ };
+};
+
+&dai {
+ status = "okay";
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+/* This is the i2c bus exposed on the DSI connector for the touch panel */
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "disabled";
+};
+
+/* This is the i2c bus exposed on the GPIO header */
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins_a>;
+ status = "disabled";
+};
+
+/* This is the i2c bus exposed on the CSI connector to control the sensor */
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins_a>;
+ status = "disabled";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>;
+ vmmc-supply = <&reg_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins_a>;
+ vmmc-supply = <&reg_aldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_8bit_pins>;
+ vmmc-supply = <&reg_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ cap-mmc-hw-reset;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&r_rsb {
+ status = "okay";
+
+ axp22x: pmic@3a3 {
+ compatible = "x-powers,axp223";
+ reg = <0x3a3>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ eldoin-supply = <&reg_dcdc1>;
+ x-powers,drive-vbus-en;
+ };
+};
+
+#include "axp223.dtsi"
+
+&ac_power_supply {
+ status = "okay";
+};
+
+&reg_aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-io";
+};
+
+&reg_aldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-name = "vdd-dll";
+};
+
+&reg_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "avcc";
+};
+
+&reg_dc1sw {
+ regulator-name = "vcc-lcd";
+};
+
+&reg_dc5ldo {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpus";
+};
+
+&reg_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+&reg_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-sys";
+};
+
+&reg_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1400000>;
+ regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+/*
+ * Our WiFi chip needs both DLDO1 and DLDO2 to be powered at the same
+ * time, with the two being in sync. Since this is not really
+ * supported right now, just use the two as always on, and we will fix
+ * it later.
+ */
+&reg_dldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi0";
+};
+
+&reg_dldo2 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi1";
+};
+
+&reg_drivevbus {
+ regulator-name = "usb0-vbus";
+ status = "okay";
+};
+
+&reg_rtc_ldo {
+ regulator-name = "vcc-rtc";
+};
+
+&sound {
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_b>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins_a>, <&uart1_pins_cts_rts_a>;
+ status = "okay";
+};
+
+&usb_otg {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usb_power_supply {
+ status = "okay";
+};
+
+&usbphy {
+ usb0_id_det-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */
+ usb0_vbus_power-supply = <&usb_power_supply>;
+ usb0_vbus-supply = <&reg_drivevbus>;
+ usb1_vbus-supply = <&reg_vcc5v0>;
+ status = "okay";
+};
--
git-series 0.9.1