[PATCH 1/2] ARM: OMAP2+: hsmmc.c: Remove dead code
From: Faiz Abbas
Date: Fri Jul 14 2017 - 08:49:21 EST
Most platforms using OMAP hsmmc driver have switched to device tree
for passing platform data to omap_hsmmc.c driver.
The hsmmc.c file in mach-omap2 exists only to support pandora board
which uses wl1251 driver in legacy platform data mode.
Hence, remove the dead code not used by the pandora board.
Signed-off-by: Faiz Abbas <faiz_abbas@xxxxxx>
---
This is only compile tested. Someone with a pandora board should help
test this for functionality.
arch/arm/mach-omap2/hsmmc.c | 239 +-------------------------------------------
arch/arm/mach-omap2/hsmmc.h | 9 --
2 files changed, 2 insertions(+), 246 deletions(-)
diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c
index be517b0..5b61438 100644
--- a/arch/arm/mach-omap2/hsmmc.c
+++ b/arch/arm/mach-omap2/hsmmc.c
@@ -32,120 +32,6 @@ static u16 control_devconf1_offset;
#define HSMMC_NAME_LEN 9
-static void omap_hsmmc1_before_set_reg(struct device *dev,
- int power_on, int vdd)
-{
- u32 reg, prog_io;
- struct omap_hsmmc_platform_data *mmc = dev->platform_data;
-
- if (mmc->remux)
- mmc->remux(dev, power_on);
-
- /*
- * Assume we power both OMAP VMMC1 (for CMD, CLK, DAT0..3) and the
- * card with Vcc regulator (from twl4030 or whatever). OMAP has both
- * 1.8V and 3.0V modes, controlled by the PBIAS register.
- *
- * In 8-bit modes, OMAP VMMC1A (for DAT4..7) needs a supply, which
- * is most naturally TWL VSIM; those pins also use PBIAS.
- *
- * FIXME handle VMMC1A as needed ...
- */
- if (power_on) {
- if (cpu_is_omap2430()) {
- reg = omap_ctrl_readl(OMAP243X_CONTROL_DEVCONF1);
- if ((1 << vdd) >= MMC_VDD_30_31)
- reg |= OMAP243X_MMC1_ACTIVE_OVERWRITE;
- else
- reg &= ~OMAP243X_MMC1_ACTIVE_OVERWRITE;
- omap_ctrl_writel(reg, OMAP243X_CONTROL_DEVCONF1);
- }
-
- if (mmc->internal_clock) {
- reg = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
- reg |= OMAP2_MMCSDIO1ADPCLKISEL;
- omap_ctrl_writel(reg, OMAP2_CONTROL_DEVCONF0);
- }
-
- reg = omap_ctrl_readl(control_pbias_offset);
- if (cpu_is_omap3630()) {
- /* Set MMC I/O to 52MHz */
- prog_io = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
- prog_io |= OMAP3630_PRG_SDMMC1_SPEEDCTRL;
- omap_ctrl_writel(prog_io, OMAP343X_CONTROL_PROG_IO1);
- } else {
- reg |= OMAP2_PBIASSPEEDCTRL0;
- }
- reg &= ~OMAP2_PBIASLITEPWRDNZ0;
- omap_ctrl_writel(reg, control_pbias_offset);
- } else {
- reg = omap_ctrl_readl(control_pbias_offset);
- reg &= ~OMAP2_PBIASLITEPWRDNZ0;
- omap_ctrl_writel(reg, control_pbias_offset);
- }
-}
-
-static void omap_hsmmc1_after_set_reg(struct device *dev, int power_on, int vdd)
-{
- u32 reg;
-
- /* 100ms delay required for PBIAS configuration */
- msleep(100);
-
- if (power_on) {
- reg = omap_ctrl_readl(control_pbias_offset);
- reg |= (OMAP2_PBIASLITEPWRDNZ0 | OMAP2_PBIASSPEEDCTRL0);
- if ((1 << vdd) <= MMC_VDD_165_195)
- reg &= ~OMAP2_PBIASLITEVMODE0;
- else
- reg |= OMAP2_PBIASLITEVMODE0;
- omap_ctrl_writel(reg, control_pbias_offset);
- } else {
- reg = omap_ctrl_readl(control_pbias_offset);
- reg |= (OMAP2_PBIASSPEEDCTRL0 | OMAP2_PBIASLITEPWRDNZ0 |
- OMAP2_PBIASLITEVMODE0);
- omap_ctrl_writel(reg, control_pbias_offset);
- }
-}
-
-static void hsmmc2_select_input_clk_src(struct omap_hsmmc_platform_data *mmc)
-{
- u32 reg;
-
- reg = omap_ctrl_readl(control_devconf1_offset);
- if (mmc->internal_clock)
- reg |= OMAP2_MMCSDIO2ADPCLKISEL;
- else
- reg &= ~OMAP2_MMCSDIO2ADPCLKISEL;
- omap_ctrl_writel(reg, control_devconf1_offset);
-}
-
-static void hsmmc2_before_set_reg(struct device *dev, int power_on, int vdd)
-{
- struct omap_hsmmc_platform_data *mmc = dev->platform_data;
-
- if (mmc->remux)
- mmc->remux(dev, power_on);
-
- if (power_on)
- hsmmc2_select_input_clk_src(mmc);
-}
-
-static int am35x_hsmmc2_set_power(struct device *dev, int power_on, int vdd)
-{
- struct omap_hsmmc_platform_data *mmc = dev->platform_data;
-
- if (power_on)
- hsmmc2_select_input_clk_src(mmc);
-
- return 0;
-}
-
-static int nop_mmc_set_power(struct device *dev, int power_on, int vdd)
-{
- return 0;
-}
-
static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
struct omap_hsmmc_platform_data *mmc)
{
@@ -157,101 +43,11 @@ static int __init omap_hsmmc_pdata_init(struct omap2_hsmmc_info *c,
return -ENOMEM;
}
- if (c->name)
- strncpy(hc_name, c->name, HSMMC_NAME_LEN);
- else
- snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i",
- c->mmc, 1);
+ snprintf(hc_name, (HSMMC_NAME_LEN + 1), "mmc%islot%i", c->mmc, 1);
mmc->name = hc_name;
mmc->caps = c->caps;
- mmc->internal_clock = !c->ext_clock;
mmc->reg_offset = 0;
- if (c->cover_only) {
- /* detect if mobile phone cover removed */
- mmc->gpio_cd = -EINVAL;
- mmc->gpio_cod = c->gpio_cd;
- } else {
- /* card detect pin on the mmc socket itself */
- mmc->gpio_cd = c->gpio_cd;
- mmc->gpio_cod = -EINVAL;
- }
- mmc->gpio_wp = c->gpio_wp;
-
- mmc->remux = c->remux;
- mmc->init_card = c->init_card;
-
- if (c->nonremovable)
- mmc->nonremovable = 1;
-
- /*
- * NOTE: MMC slots should have a Vcc regulator set up.
- * This may be from a TWL4030-family chip, another
- * controllable regulator, or a fixed supply.
- *
- * temporary HACK: ocr_mask instead of fixed supply
- */
- if (soc_is_am35xx())
- mmc->ocr_mask = MMC_VDD_165_195 |
- MMC_VDD_26_27 |
- MMC_VDD_27_28 |
- MMC_VDD_29_30 |
- MMC_VDD_30_31 |
- MMC_VDD_31_32;
- else
- mmc->ocr_mask = c->ocr_mask;
-
- if (!soc_is_am35xx())
- mmc->features |= HSMMC_HAS_PBIAS;
-
- switch (c->mmc) {
- case 1:
- if (mmc->features & HSMMC_HAS_PBIAS) {
- /* on-chip level shifting via PBIAS0/PBIAS1 */
- mmc->before_set_reg =
- omap_hsmmc1_before_set_reg;
- mmc->after_set_reg =
- omap_hsmmc1_after_set_reg;
- }
-
- if (soc_is_am35xx())
- mmc->set_power = nop_mmc_set_power;
-
- /* OMAP3630 HSMMC1 supports only 4-bit */
- if (cpu_is_omap3630() &&
- (c->caps & MMC_CAP_8_BIT_DATA)) {
- c->caps &= ~MMC_CAP_8_BIT_DATA;
- c->caps |= MMC_CAP_4_BIT_DATA;
- mmc->caps = c->caps;
- }
- break;
- case 2:
- if (soc_is_am35xx())
- mmc->set_power = am35x_hsmmc2_set_power;
-
- if (c->ext_clock)
- c->transceiver = 1;
- if (c->transceiver && (c->caps & MMC_CAP_8_BIT_DATA)) {
- c->caps &= ~MMC_CAP_8_BIT_DATA;
- c->caps |= MMC_CAP_4_BIT_DATA;
- }
- if (mmc->features & HSMMC_HAS_PBIAS) {
- /* off-chip level shifting, or none */
- mmc->before_set_reg = hsmmc2_before_set_reg;
- mmc->after_set_reg = NULL;
- }
- break;
- case 3:
- case 4:
- case 5:
- mmc->before_set_reg = NULL;
- mmc->after_set_reg = NULL;
- break;
- default:
- pr_err("MMC%d configuration not supported!\n", c->mmc);
- kfree(hc_name);
- return -ENODEV;
- }
return 0;
}
@@ -260,7 +56,6 @@ static int omap_hsmmc_done;
void omap_hsmmc_late_init(struct omap2_hsmmc_info *c)
{
struct platform_device *pdev;
- struct omap_hsmmc_platform_data *mmc_pdata;
int res;
if (omap_hsmmc_done != 1)
@@ -269,32 +64,12 @@ void omap_hsmmc_late_init(struct omap2_hsmmc_info *c)
omap_hsmmc_done++;
for (; c->mmc; c++) {
- if (!c->deferred)
- continue;
-
pdev = c->pdev;
if (!pdev)
continue;
-
- mmc_pdata = pdev->dev.platform_data;
- if (!mmc_pdata)
- continue;
-
- if (c->cover_only) {
- /* detect if mobile phone cover removed */
- mmc_pdata->gpio_cd = -EINVAL;
- mmc_pdata->gpio_cod = c->gpio_cd;
- } else {
- /* card detect pin on the mmc socket itself */
- mmc_pdata->gpio_cd = c->gpio_cd;
- mmc_pdata->gpio_cod = -EINVAL;
- }
- mmc_pdata->gpio_wp = c->gpio_wp;
-
res = omap_device_register(pdev);
if (res)
- pr_err("Could not late init MMC %s\n",
- c->name);
+ pr_err("Could not late init MMC\n");
}
}
@@ -336,13 +111,6 @@ static void __init omap_hsmmc_init_one(struct omap2_hsmmc_info *hsmmcinfo,
if (oh->dev_attr != NULL) {
mmc_dev_attr = oh->dev_attr;
mmc_data->controller_flags = mmc_dev_attr->flags;
- /*
- * erratum 2.1.1.128 doesn't apply if board has
- * a transceiver is attached
- */
- if (hsmmcinfo->transceiver)
- mmc_data->controller_flags &=
- ~OMAP_HSMMC_BROKEN_MULTIBLOCK_READ;
}
pdev = platform_device_alloc(name, ctrl_nr - 1);
@@ -367,9 +135,6 @@ static void __init omap_hsmmc_init_one(struct omap2_hsmmc_info *hsmmcinfo,
hsmmcinfo->pdev = pdev;
- if (hsmmcinfo->deferred)
- goto free_mmc;
-
res = omap_device_register(pdev);
if (res) {
pr_err("Could not register od for %s\n", name);
diff --git a/arch/arm/mach-omap2/hsmmc.h b/arch/arm/mach-omap2/hsmmc.h
index 69b619d..af9af50 100644
--- a/arch/arm/mach-omap2/hsmmc.h
+++ b/arch/arm/mach-omap2/hsmmc.h
@@ -12,18 +12,9 @@ struct omap2_hsmmc_info {
u8 mmc; /* controller 1/2/3 */
u32 caps; /* 4/8 wires and any additional host
* capabilities OR'd (ref. linux/mmc/host.h) */
- bool transceiver; /* MMC-2 option */
- bool ext_clock; /* use external pin for input clock */
- bool cover_only; /* No card detect - just cover switch */
- bool nonremovable; /* Nonremovable e.g. eMMC */
- bool deferred; /* mmc needs a deferred probe */
int gpio_cd; /* or -EINVAL */
int gpio_wp; /* or -EINVAL */
- char *name; /* or NULL for default */
struct platform_device *pdev; /* mmc controller instance */
- int ocr_mask; /* temporary HACK */
- /* Remux (pad configuration) when powering on/off */
- void (*remux)(struct device *dev, int power_on);
/* init some special card */
void (*init_card)(struct mmc_card *card);
};
--
2.7.4