Re: [PATCH 11/18] dt-bindings: display: Add Allwinner MIPI-DSI bindings

[Maxime Ripard]

Hi Laurent

On Tue, Jul 18, 2017 at 01:18:42PM +0300, Laurent Pinchart wrote:
> On Monday 17 Jul 2017 13:41:49 Rob Herring wrote:
> > On Thu, Jul 13, 2017 at 04:13:06PM +0200, Maxime Ripard wrote:
> > > The Allwinner SoCs usually come with a DSI encoder. Add a binding for it.
> > > 
> > > Signed-off-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxxxxxxxxx>
> > > ---
> > > 
> > >  Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt | 85
> > >  +++++++-
> > >  1 file changed, 85 insertions(+)
> > >  create mode 100644
> > >  Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt> 
> > > diff --git a/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > > b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt new file
> > > mode 100644
> > > index 000000000000..2e7c5aa7020f
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/display/sunxi/sun6i-dsi.txt
> > > @@ -0,0 +1,85 @@
> > > +Allwinner A31 DSI Encoder
> > > +=========================
> > > +
> > > +The DSI pipeline consists of two separate blocks: the DSI controller
> > > +itself, and its associated D-PHY.
> > > +
> > > +DSI Encoder
> > > +-----------
> > > +
> > > +The DSI Encoder generates the DSI signal from the TCON's.
> > > +
> > > +Required properties:
> > > +  - compatible: value must be one of:
> > > +    * allwinner,sun6i-a31-mipi-dsi
> > > +  - reg: base address and size of memory-mapped region
> > > +  - interrupts: interrupt associated to this IP
> > > +  - clocks: phandles to the clocks feeding the DSI encoder
> > > +    * bus: the DSI interface clock
> > > +    * mod: the DSI module clock
> > > +  - clock-names: the clock names mentioned above
> > > +  - phys: phandle to the D-PHY
> > > +  - phy-names: must be "dphy"
> > > +  - resets: phandle to the reset controller driving the encoder
> > > +
> > > +  - ports: A ports node with endpoint definitions as defined in
> > > +    Documentation/devicetree/bindings/media/video-interfaces.txt. The
> > > +    port should be the input endpoint, usually coming from the
> > > +    associated TCON.
> > 
> > Output port for bridge/panel?
> > 
> > > +
> > > +D-PHY
> > > +-----
> > > +
> > > +Required properties:
> > > +  - compatible: value must be one of:
> > > +    * allwinner,sun6i-a31-mipi-dphy
> > > +  - reg: base address and size of memory-mapped region
> > > +  - clocks: phandles to the clocks feeding the DSI encoder
> > > +    * bus: the DSI interface clock
> > > +    * mod: the DSI module clock
> > > +  - clock-names: the clock names mentioned above
> > > +  - resets: phandle to the reset controller driving the encoder
> > > +
> > > +Example:
> > > +
> > > +dsi0: dsi@01ca0000 {
> > 
> > Drop the leading 0.
> > 
> > > +	compatible = "allwinner,sun6i-a31-mipi-dsi";
> > > +	reg = <0x01ca0000 0x1000>;
> > > +	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> > > +	clocks = <&ccu CLK_BUS_MIPI_DSI>,
> > > +		 <&ccu CLK_DSI_SCLK>;
> > > +	clock-names = "bus", "mod";
> > > +	resets = <&ccu RST_BUS_MIPI_DSI>;
> > > +	phys = <&dphy0>;
> > > +	phy-names = "dphy";
> > > 
> > > +	#address-cells = <1>;
> > > +	#size-cells = <0>;
> > 
> > Not needed.
> > 
> > > +
> > > +	ports {
> > > +		#address-cells = <1>;
> > > +		#size-cells = <0>;
> > > +
> > > +		dsi0_in: port@0 {
> 
> I don't think the label for the port is needed, you should only reference the 
> endpoint.
> 
> > > +			#address-cells = <1>;
> > > +			#size-cells = <0>;
> > > +			reg = <0>;
> > > +
> > > +			dsi0_in_tcon0: endpoint@0 {
> > > +				reg = <0>;
> > 
> > Don't need reg when there's only 1 endpoint.
> 
> And no reg for the port name either when there's a single port. This can all 
> be simplified to
> 
> dsi0: dsi@1ca0000 {
> 	compatible = "allwinner,sun6i-a31-mipi-dsi";
> 	reg = <0x01ca0000 0x1000>;
> 	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
> 	clocks = <&ccu CLK_BUS_MIPI_DSI>,
> 		 <&ccu CLK_DSI_SCLK>;
> 	clock-names = "bus", "mod";
> 	resets = <&ccu RST_BUS_MIPI_DSI>;
> 	phys = <&dphy0>;
> 	phy-names = "dphy";
> 
> 	port {
> 		dsi0_in_tcon0: endpoint {
> 			remote-endpoint = <&tcon0_out_dsi0>;
> 		};
> 	};
> };

I'll change that. Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com

Attachment: signature.asc
Description: PGP signature