Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4

From: Zdenek Kabelac
Date: Tue Jul 25 2017 - 06:06:27 EST

Next message: Andy Shevchenko: "Re: [PATCH v2 2/6] mei: Switch to use new generic UUID API"
Previous message: David Wu: "[PATCH] arm64: dts: rockchip: Add rk3328 io-domain node"
In reply to: Guenter Roeck: "Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4"
Next in thread: Alan Stern: "Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

Dne 24.7.2017 v 16:41 Alan Stern napsal(a):

On Mon, 24 Jul 2017, Zdenek Kabelac wrote:

Hi

I've problem with my USB storage devices: WD Elements 1TB.
(Bus 004 Device 002: ID 1058:10a8 Western Digital Technologies, Inc. Elements
Portable (WDBUZG))

After kernel >4.9 when disk is attached via cable it has very low speed
(less then 1MB/s).

It can run at full speed (>22MB/s) when the Linux kernel is fully rebooted (so
disk is attached during the reboot of Lenovo T61, C2D, Fedora Rawhide).

However when >4.9 kernel is running and disk is just attached it's very slow.

I've played a bisect game - and the clean result has been:

22547c4cc4fe20698a6a85a55b8788859134b8e4

When I just revert this patch with 4.13-rc1 - it's again running with full
speed even when disk is attached (thus no reboot is needed for full speed).

So while I've no idea what 22547c4cc4fe20698... is doing, it seems to have
some unpleasant side-effect on regular USB devices.

So what else is needed to get this properly working ?
(assuming plain revert of 22547c4cc4fe20698 is unwanted).

What more info can I provide to get this storage 'normally' usable without
rebooting the machine.

Please post the dmesg logs showing what happens when the disk is
first attached and operates slowly, and what happens when the disk is
attached following a reboot and operates normally.

So I'm attaching kernel traces from kernel 4.8 & 4.12 from T61.

Both are from full boot (all kernel: messages)

In both cases - boot was with USB WD disk attached -
then I've detached USB disk and reattached again.

On 4.8 this had normal speed all the time
On 4.12 after reattach -> slow speed.

I should also add that on Lenovo T440s - there seems to be NO slowdown
when this WD Element drive is attached it works normally all the time.

So it could be probably related to USB chipset on T61 ??

For completeness I'm also attaching boot kernel trace from T440s where USB disk is just attached and works with normal speed.

Zdenek

Attachment: k4.8
Description: Unix manual page

06:18 Linux version 4.12.0-1.fc27.x86_64 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 7.1.1 20170526 (Red Hat 7.1.1-2) (GCC) ) #1 SMP Mon Jul 3 15:45:36 UTC 2017
06:18 Command line: BOOT_IMAGE=/vmlinuz-4.12.0-1.fc27.x86_64 root=/dev/sda2 ro selinux=0 kmemleak=off lockdep.prove_locking=0 lockdep.lock_stat=0 systemd.log_level=info systemd.log_target=kmsg acpi_backlight=vendor log_buf_len=2M quiet
06:18 x86/fpu: x87 FPU will use FXSAVE
06:18 e820: BIOS-provided physical RAM map:
06:18 BIOS-e820: [mem 0x0000000000000000-0x000000000009d7ff] usable
06:18 BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
06:18 BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
06:18 BIOS-e820: [mem 0x0000000000100000-0x00000000bf6affff] usable
06:18 BIOS-e820: [mem 0x00000000bf6b0000-0x00000000bf6cbfff] ACPI data
06:18 BIOS-e820: [mem 0x00000000bf6cc000-0x00000000bf6fffff] ACPI NVS
06:18 BIOS-e820: [mem 0x00000000bf700000-0x00000000bfffffff] reserved
06:18 BIOS-e820: [mem 0x00000000f0000000-0x00000000f3ffffff] reserved
06:18 BIOS-e820: [mem 0x00000000fec00000-0x00000000fec0ffff] reserved
06:18 BIOS-e820: [mem 0x00000000fed00000-0x00000000fed003ff] reserved
06:18 BIOS-e820: [mem 0x00000000fed14000-0x00000000fed19fff] reserved
06:18 BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed8ffff] reserved
06:18 BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
06:18 BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
06:18 BIOS-e820: [mem 0x0000000100000000-0x000000013bffffff] usable
06:18 NX (Execute Disable) protection: active
06:18 SMBIOS 2.4 present.
06:18 DMI: LENOVO 6464CTO/6464CTO, BIOS 7LETC9WW (2.29 ) 03/18/2011
06:18 tsc: Fast TSC calibration failed
06:18 tsc: Using PIT calibration value
06:18 e820: last_pfn = 0x13c000 max_arch_pfn = 0x400000000
06:18 x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
06:18 e820: last_pfn = 0xbf6b0 max_arch_pfn = 0x400000000
06:18 found SMP MP-table at [mem 0x000f68f0-0x000f68ff] mapped at [ffff8919400f68f0]
06:18 log_buf_len: 2097152 bytes
06:18 early log buf free: 258320(98%)
06:18 RAMDISK: [mem 0x3634d000-0x3719efff]
06:18 ACPI: Early table checksum verification disabled
06:18 ACPI: RSDP 0x00000000000F68C0 000024 (v02 LENOVO)
06:18 ACPI: XSDT 0x00000000BF6BB496 00009C (v01 LENOVO TP-7U 00002290 LTP 00000000)
06:18 ACPI: FACP 0x00000000BF6BB600 0000F4 (v03 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI BIOS Warning (bug): 32/64X length mismatch in FADT/Gpe0Block: 64/32 (20170303/tbfadt-603)
06:18 ACPI BIOS Warning (bug): Optional FADT field Gpe1Block has valid Address but zero Length: 0x000000000000102C/0x0 (20170303/tbfadt-658)
06:18 ACPI: DSDT 0x00000000BF6BBA1D 01003C (v01 LENOVO TP-7U 00002290 MSFT 03000000)
06:18 ACPI: FACS 0x00000000BF6E4000 000040
06:18 ACPI: FACS 0x00000000BF6E4000 000040
06:18 ACPI: SSDT 0x00000000BF6BB7B4 000269 (v01 LENOVO TP-7U 00002290 MSFT 03000000)
06:18 ACPI: ECDT 0x00000000BF6CBA59 000052 (v01 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI: TCPA 0x00000000BF6CBAAB 000032 (v02 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI: APIC 0x00000000BF6CBADD 000068 (v01 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI: MCFG 0x00000000BF6CBB45 00003C (v01 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI: HPET 0x00000000BF6CBB81 000038 (v01 LENOVO TP-7U 00002290 LNVO 00000001)
06:18 ACPI: SLIC 0x00000000BF6CBBB9 000176 (v01 LENOVO TP-7U 00002290 LTP 00000000)
06:18 ACPI: SLAC 0x00000000BF6CBDF0 000176 (v01 LENOVO TP-7U 00002290 LTP 00000000)
06:18 ACPI: BOOT 0x00000000BF6CBF66 000028 (v01 LENOVO TP-7U 00002290 LTP 00000001)
06:18 ACPI: ASF! 0x00000000BF6CBF8E 000072 (v16 LENOVO TP-7U 00002290 PTL 00000001)
06:18 ACPI: SSDT 0x00000000BF6E26D9 00025F (v01 LENOVO TP-7U 00002290 INTL 20050513)
06:18 ACPI: SSDT 0x00000000BF6E2938 0000A6 (v01 LENOVO TP-7U 00002290 INTL 20050513)
06:18 ACPI: SSDT 0x00000000BF6E29DE 0004F7 (v01 LENOVO TP-7U 00002290 INTL 20050513)
06:18 ACPI: SSDT 0x00000000BF6E2ED5 0001D8 (v01 LENOVO TP-7U 00002290 INTL 20050513)
06:18 No NUMA configuration found
06:18 Faking a node at [mem 0x0000000000000000-0x000000013bffffff]
06:18 NODE_DATA(0) allocated [mem 0x13bdd5000-0x13bdfffff]
06:18 Zone ranges:
06:18 DMA [mem 0x0000000000001000-0x0000000000ffffff]
06:18 DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
06:18 Normal [mem 0x0000000100000000-0x000000013bffffff]
06:18 Device empty
06:18 Movable zone start for each node
06:18 Early memory node ranges
06:18 node 0: [mem 0x0000000000001000-0x000000000009cfff]
06:18 node 0: [mem 0x0000000000100000-0x00000000bf6affff]
06:18 node 0: [mem 0x0000000100000000-0x000000013bffffff]
06:18 Initmem setup node 0 [mem 0x0000000000001000-0x000000013bffffff]
06:18 Reserving Intel graphics memory at 0x00000000bf800000-0x00000000bfffffff
06:18 ACPI: PM-Timer IO Port: 0x1008
06:18 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
06:18 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
06:18 IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
06:18 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
06:18 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
06:18 Using ACPI (MADT) for SMP configuration information
06:18 ACPI: HPET id: 0x8086a201 base: 0xfed00000
06:18 smpboot: Allowing 2 CPUs, 0 hotplug CPUs
06:18 PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
06:18 PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
06:18 PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
06:18 PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
06:18 PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
06:18 PM: Registered nosave memory: [mem 0xbf6b0000-0xbf6cbfff]
06:18 PM: Registered nosave memory: [mem 0xbf6cc000-0xbf6fffff]
06:18 PM: Registered nosave memory: [mem 0xbf700000-0xbfffffff]
06:18 PM: Registered nosave memory: [mem 0xc0000000-0xefffffff]
06:18 PM: Registered nosave memory: [mem 0xf0000000-0xf3ffffff]
06:18 PM: Registered nosave memory: [mem 0xf4000000-0xfebfffff]
06:18 PM: Registered nosave memory: [mem 0xfec00000-0xfec0ffff]
06:18 PM: Registered nosave memory: [mem 0xfec10000-0xfecfffff]
06:18 PM: Registered nosave memory: [mem 0xfed00000-0xfed13fff]
06:18 PM: Registered nosave memory: [mem 0xfed14000-0xfed19fff]
06:18 PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
06:18 PM: Registered nosave memory: [mem 0xfed1c000-0xfed8ffff]
06:18 PM: Registered nosave memory: [mem 0xfed90000-0xfedfffff]
06:18 PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
06:18 PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
06:18 PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
06:18 e820: [mem 0xc0000000-0xefffffff] available for PCI devices
06:18 Booting paravirtualized kernel on bare hardware
06:18 clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
06:18 setup_percpu: NR_CPUS:8192 nr_cpumask_bits:2 nr_cpu_ids:2 nr_node_ids:1
06:18 percpu: Embedded 37 pages/cpu @ffff891a7ba00000 s111640 r8192 d31720 u1048576
06:18 Built 1 zonelists in Node order, mobility grouping on. Total pages: 1013596
06:18 Policy zone: Normal
06:18 Kernel command line: BOOT_IMAGE=/vmlinuz-4.12.0-1.fc27.x86_64 root=/dev/sda2 ro selinux=0 kmemleak=off lockdep.prove_locking=0 lockdep.lock_stat=0 systemd.log_level=info systemd.log_target=kmsg acpi_backlight=vendor log_buf_len=2M quiet
06:18 PID hash table entries: 4096 (order: 3, 32768 bytes)
06:18 Memory: 3948948K/4118832K available (8693K kernel code, 2407K rwdata, 3692K rodata, 2164K init, 1980K bss, 169884K reserved, 0K cma-reserved)
06:18 SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
06:18 ftrace: allocating 34435 entries in 135 pages
06:18
06:18 **********************************************************
06:18 ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
06:18 ** **
06:18 ** trace_printk() being used. Allocating extra memory. **
06:18 ** **
06:18 ** This means that this is a DEBUG kernel and it is **
06:18 ** unsafe for production use. **
06:18 ** **
06:18 ** If you see this message and you are not debugging **
06:18 ** the kernel, report this immediately to your vendor! **
06:18 ** **
06:18 ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
06:18 **********************************************************
06:18 Hierarchical RCU implementation.
06:18 #011RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=2.
06:18 RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
06:18 NR_IRQS:524544 nr_irqs:440 16
06:18 #011Offload RCU callbacks from all CPUs
06:18 #011Offload RCU callbacks from CPUs: 0-1.
06:18 Console: colour VGA+ 80x25
06:18 console [tty0] enabled
06:18 clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
06:18 tsc: Fast TSC calibration using PIT
06:18 tsc: Detected 2194.450 MHz processor
06:18 Calibrating delay loop (skipped), value calculated using timer frequency.. 4388.90 BogoMIPS (lpj=2194450)
06:18 pid_max: default: 32768 minimum: 301
06:18 ACPI: Core revision 20170303
06:18 ACPI: 6 ACPI AML tables successfully acquired and loaded
06:18 Security Framework initialized
06:18 Yama: becoming mindful.
06:18 SELinux: Disabled at boot.
06:18 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
06:18 Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
06:18 Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
06:18 Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
06:18 CPU: Physical Processor ID: 0
06:18 CPU: Processor Core ID: 0
06:18 mce: CPU supports 6 MCE banks
06:18 CPU0: Thermal monitoring enabled (TM2)
06:18 process: using mwait in idle threads
06:18 Last level iTLB entries: 4KB 128, 2MB 4, 4MB 4
06:18 Last level dTLB entries: 4KB 256, 2MB 0, 4MB 32, 1GB 0
06:18 Freeing SMP alternatives memory: 32K
06:18 smpboot: Max logical packages: 1
06:18 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
06:18 smpboot: CPU0: Intel(R) Core(TM)2 Duo CPU T7500 @ 2.20GHz (family: 0x6, model: 0xf, stepping: 0xa)
06:18 Performance Events: PEBS fmt0+, Core2 events, Intel PMU driver.
06:18 core: PEBS disabled due to CPU errata
06:18 ... version: 2
06:18 ... bit width: 40
06:18 ... generic registers: 2
06:18 ... value mask: 000000ffffffffff
06:18 ... max period: 000000007fffffff
06:18 ... fixed-purpose events: 3
06:18 ... event mask: 0000000700000003
06:18 NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
06:18 smp: Bringing up secondary CPUs ...
06:18 x86: Booting SMP configuration:
06:18 .... node #0, CPUs: #1
06:18 TSC synchronization [CPU#0 -> CPU#1]:
06:18 Measured 399465 cycles TSC warp between CPUs, turning off TSC clock.
06:18 tsc: Marking TSC unstable due to check_tsc_sync_source failed
06:18 smp: Brought up 1 node, 2 CPUs
06:18 smpboot: Total of 2 processors activated (8777.65 BogoMIPS)
06:18 devtmpfs: initialized
06:18 x86/mm: Memory block size: 128MB
06:18 PM: Registering ACPI NVS region [mem 0xbf6cc000-0xbf6fffff] (212992 bytes)
06:18 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
06:18 futex hash table entries: 512 (order: 3, 32768 bytes)
06:18 pinctrl core: initialized pinctrl subsystem
06:18 RTC time: 18:06:17, date: 07/24/17
06:18 NET: Registered protocol family 16
06:18 cpuidle: using governor menu
06:18 PCCT header not found.
06:18 Simple Boot Flag at 0x35 set to 0x1
06:18 ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
06:18 ACPI: bus type PCI registered
06:18 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
06:18 PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf0000000-0xf3ffffff] (base 0xf0000000)
06:18 PCI: MMCONFIG at [mem 0xf0000000-0xf3ffffff] reserved in E820
06:18 pmd_set_huge: Cannot satisfy [mem 0xf0000000-0xf0200000] with a huge-page mapping due to MTRR override.
06:18 PCI: Using configuration type 1 for base access
06:18 HugeTLB registered 2 MB page size, pre-allocated 0 pages
06:18 ACPI: Added _OSI(Module Device)
06:18 ACPI: Added _OSI(Processor Device)
06:18 ACPI: Added _OSI(3.0 _SCP Extensions)
06:18 ACPI: Added _OSI(Processor Aggregator Device)
06:18 ACPI : EC: EC started
06:18 ACPI : EC: interrupt blocked
06:18 ACPI: \: Used as first EC
06:18 ACPI: \: GPE=0x12, EC_CMD/EC_SC=0x66, EC_DATA=0x62
06:18 ACPI: \: Used as boot ECDT EC to handle transactions
06:18 ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
06:18 ACPI: Dynamic OEM Table Load:
06:18 ACPI: SSDT 0xFFFF891A76063000 0002C4 (v01 PmRef Cpu0Ist 00000100 INTL 20050513)
06:18 ACPI: Dynamic OEM Table Load:
06:18 ACPI: SSDT 0xFFFF891A77254000 00085E (v01 PmRef Cpu0Cst 00000100 INTL 20050513)
06:18 ACPI: Dynamic OEM Table Load:
06:18 ACPI: SSDT 0xFFFF891A7605CF00 0000C8 (v01 PmRef Cpu1Ist 00000100 INTL 20050513)
06:18 ACPI: Dynamic OEM Table Load:
06:18 ACPI: SSDT 0xFFFF891A760779C0 000085 (v01 PmRef Cpu1Cst 00000100 INTL 20050513)
06:18 ACPI : EC: EC stopped
06:18 ACPI : EC: EC started
06:18 ACPI : EC: interrupt blocked
06:18 ACPI: \_SB_.PCI0.LPC_.EC__: Used as first EC
06:18 ACPI: \_SB_.PCI0.LPC_.EC__: GPE=0x12, EC_CMD/EC_SC=0x66, EC_DATA=0x62
06:18 ACPI: \_SB_.PCI0.LPC_.EC__: Used as boot DSDT EC to handle transactions
06:18 ACPI: Interpreter enabled
06:18 ACPI: (supports S0 S3 S4 S5)
06:18 ACPI: Using IOAPIC for interrupt routing
06:18 PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
06:18 ACPI: Power Resource [PUBS] (on)
06:18 acpi PNP0C0A:01: ACPI dock station (docks/bays count: 1)
06:18 acpi LNXIOBAY:00: ACPI dock station (docks/bays count: 2)
06:18 acpi IBM0079:00: ACPI dock station (docks/bays count: 3)
06:18 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11)
06:18 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
06:18 ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
06:18 acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
06:18 acpi PNP0A08:00: _OSC: OS now controls [PCIeHotplug PME AER PCIeCapability]
06:18 acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS configuration
06:18 acpi PNP0A08:00: [Firmware Info]: MMCONFIG for domain 0000 [bus 00-3f] only partially covers this bridge
06:18 PCI host bridge to bus 0000:00
06:18 pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
06:18 pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
06:18 pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
06:18 pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
06:18 pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
06:18 pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
06:18 pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
06:18 pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window]
06:18 pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed4bfff window]
06:18 pci_bus 0000:00: root bus resource [bus 00-ff]
06:18 pci 0000:00:19.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1a.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1a.1: System wakeup disabled by ACPI
06:18 pci 0000:00:1a.7: System wakeup disabled by ACPI
06:18 pci 0000:00:1b.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1c.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1c.1: System wakeup disabled by ACPI
06:18 pci 0000:00:1c.2: System wakeup disabled by ACPI
06:18 pci 0000:00:1d.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1d.1: System wakeup disabled by ACPI
06:18 pci 0000:00:1d.2: System wakeup disabled by ACPI
06:18 pci 0000:00:1d.7: System wakeup disabled by ACPI
06:18 pci 0000:00:1e.0: System wakeup disabled by ACPI
06:18 pci 0000:00:1f.0: quirk: [io 0x1000-0x107f] claimed by ICH6 ACPI/GPIO/TCO
06:18 pci 0000:00:1f.0: quirk: [io 0x1180-0x11bf] claimed by ICH6 GPIO
06:18 pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 1600 (mask 007f)
06:18 pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 15e0 (mask 000f)
06:18 pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 1680 (mask 001f)
06:18 pci 0000:00:1f.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7]
06:18 pci 0000:00:1f.1: legacy IDE quirk: reg 0x14: [io 0x03f6]
06:18 pci 0000:00:1f.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177]
06:18 pci 0000:00:1f.1: legacy IDE quirk: reg 0x1c: [io 0x0376]
06:18 pci 0000:00:1c.0: PCI bridge to [bus 02]
06:18 pci 0000:00:1c.1: PCI bridge to [bus 03]
06:18 pci 0000:00:1c.2: PCI bridge to [bus 04]
06:18 pci 0000:15:00.0: proprietary Ricoh MMC controller disabled (via cardbus function)
06:18 pci 0000:15:00.0: MMC cards are now supported by standard SDHCI controller
06:18 pci 0000:00:1e.0: PCI bridge to [bus 15-18] (subtractive decode)
06:18 ACPI: Enabled 3 GPEs in block 00 to 1F
06:18 ACPI : EC: interrupt unblocked
06:18 ACPI : EC: event unblocked
06:18 ACPI: \_SB_.PCI0.LPC_.EC__: GPE=0x12, EC_CMD/EC_SC=0x66, EC_DATA=0x62
06:18 ACPI: \_SB_.PCI0.LPC_.EC__: Used as boot DSDT EC to handle transactions and events
06:18 pci 0000:00:02.0: vgaarb: setting as boot VGA device
06:18 pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
06:18 pci 0000:00:02.0: vgaarb: bridge control possible
06:18 vgaarb: loaded
06:18 SCSI subsystem initialized
06:18 ACPI: bus type USB registered
06:18 usbcore: registered new interface driver usbfs
06:18 usbcore: registered new interface driver hub
06:18 usbcore: registered new device driver usb
06:18 EDAC MC: Ver: 3.0.0
06:18 PCI: Using ACPI for IRQ routing
06:18 NetLabel: Initializing
06:18 NetLabel: domain hash size = 128
06:18 NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
06:18 NetLabel: unlabeled traffic allowed by default
06:18 HPET: 3 timers in total, 0 timers will be used for per-cpu timer
06:18 hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
06:18 hpet0: 3 comparators, 64-bit 14.318180 MHz counter
06:18 clocksource: Switched to clocksource hpet
06:18 VFS: Disk quotas dquot_6.6.0
06:18 VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
06:18 pnp: PnP ACPI init
06:18 system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
06:18 system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
06:18 system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
06:18 system 00:00: [mem 0x000c8000-0x000cbfff] has been reserved
06:18 system 00:00: [mem 0x000cc000-0x000cffff] has been reserved
06:18 system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
06:18 system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
06:18 system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
06:18 system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
06:18 system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
06:18 system 00:00: [mem 0x00100000-0xbfffffff] could not be reserved
06:18 system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
06:18 system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
06:18 system 00:01: [io 0x164e-0x164f] has been reserved
06:18 system 00:01: [io 0x1000-0x107f] has been reserved
06:18 system 00:01: [io 0x1180-0x11bf] has been reserved
06:18 system 00:01: [io 0x0800-0x080f] has been reserved
06:18 system 00:01: [io 0x15e0-0x15ef] has been reserved
06:18 system 00:01: [io 0x1600-0x165f] could not be reserved
06:18 system 00:01: [mem 0xf0000000-0xf3ffffff] has been reserved
06:18 system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
06:18 system 00:01: [mem 0xfed14000-0xfed17fff] has been reserved
06:18 system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
06:18 system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
06:18 system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
06:18 pnp: PnP ACPI: found 6 devices
06:18 clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
06:18 pci 0000:00:1c.0: PCI bridge to [bus 02]
06:18 pci 0000:00:1c.0: bridge window [io 0x2000-0x2fff]
06:18 pci 0000:00:1c.0: bridge window [mem 0xfc000000-0xfdffffff]
06:18 pci 0000:00:1c.0: bridge window [mem 0xf8000000-0xf80fffff 64bit pref]
06:18 pci 0000:00:1c.1: PCI bridge to [bus 03]
06:18 pci 0000:00:1c.1: bridge window [io 0x3000-0x3fff]
06:18 pci 0000:00:1c.1: bridge window [mem 0xdc100000-0xdf6fffff]
06:18 pci 0000:00:1c.1: bridge window [mem 0xdfe00000-0xdfefffff 64bit pref]
06:18 pci 0000:00:1c.2: PCI bridge to [bus 04]
06:18 pci 0000:00:1c.2: bridge window [io 0x4000-0x4fff]
06:18 pci 0000:00:1c.2: bridge window [mem 0xd8000000-0xd9ffffff]
06:18 pci 0000:00:1c.2: bridge window [mem 0xdfb00000-0xdfbfffff 64bit pref]
06:18 pci 0000:15:00.0: BAR 15: assigned [mem 0xf4000000-0xf7ffffff pref]
06:18 pci 0000:15:00.0: BAR 16: assigned [mem 0xc0000000-0xc3ffffff]
06:18 pci 0000:15:00.0: BAR 13: assigned [io 0x6000-0x60ff]
06:18 pci 0000:15:00.0: BAR 14: assigned [io 0x6400-0x64ff]
06:18 pci 0000:15:00.0: CardBus bridge to [bus 16-17]
06:18 pci 0000:15:00.0: bridge window [io 0x6000-0x60ff]
06:18 pci 0000:15:00.0: bridge window [io 0x6400-0x64ff]
06:18 pci 0000:15:00.0: bridge window [mem 0xf4000000-0xf7ffffff pref]
06:18 pci 0000:15:00.0: bridge window [mem 0xc0000000-0xc3ffffff]
06:18 pci 0000:00:1e.0: PCI bridge to [bus 15-18]
06:18 pci 0000:00:1e.0: bridge window [io 0x6000-0x9fff]
06:18 pci 0000:00:1e.0: bridge window [mem 0xf8300000-0xfbffffff]
06:18 pci 0000:00:1e.0: bridge window [mem 0xf4000000-0xf7ffffff 64bit pref]
06:18 NET: Registered protocol family 2
06:18 TCP established hash table entries: 32768 (order: 6, 262144 bytes)
06:18 TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
06:18 TCP: Hash tables configured (established 32768 bind 32768)
06:18 UDP hash table entries: 2048 (order: 4, 65536 bytes)
06:18 UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
06:18 NET: Registered protocol family 1
06:18 pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
06:18 Unpacking initramfs...
06:18 Freeing initrd memory: 14664K
06:18 PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
06:18 software IO TLB [mem 0xbb6b0000-0xbf6b0000] (64MB) mapped at [ffff8919fb6b0000-ffff8919ff6affff]
06:18 clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x1fa1b8037fd, max_idle_ns: 440795241812 ns
06:18 Initialise system trusted keyrings
06:18 Key type blacklist registered
06:18 workingset: timestamp_bits=36 max_order=20 bucket_order=0
06:18 zbud: loaded
06:18 NET: Registered protocol family 38
06:18 Key type asymmetric registered
06:18 Asymmetric key parser 'x509' registered
06:18 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
06:18 io scheduler noop registered
06:18 io scheduler deadline registered
06:18 io scheduler cfq registered (default)
06:18 io scheduler mq-deadline registered
06:18 atomic64_test: passed for x86-64 platform with CX8 and with SSE
06:18 pcieport 0000:00:1c.0: Signaling PME with IRQ 24
06:18 pcieport 0000:00:1c.1: Signaling PME with IRQ 25
06:18 pcieport 0000:00:1c.2: Signaling PME with IRQ 26
06:18 pciehp 0000:00:1c.0:pcie004: Slot #2 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl- LLActRep+
06:18 pciehp 0000:00:1c.1:pcie004: Slot #3 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl- LLActRep+
06:18 pciehp 0000:00:1c.2:pcie004: Slot #4 AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+ Interlock- NoCompl- LLActRep+
06:18 ACPI: AC Adapter [AC] (on-line)
06:18 input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
06:18 ACPI: Lid Switch [LID]
06:18 input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
06:18 ACPI: Sleep Button [SLPB]
06:18 input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
06:18 ACPI: Power Button [PWRF]
06:18 (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
06:18 thermal LNXTHERM:00: registered as thermal_zone0
06:18 ACPI: Thermal Zone [THM0] (54 C)
06:18 thermal LNXTHERM:01: registered as thermal_zone1
06:18 ACPI: Thermal Zone [THM1] (51 C)
06:18 GHES: HEST is not enabled!
06:18 Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
06:18 Non-volatile memory driver v1.3
06:18 Linux agpgart interface v0.103
06:18 ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
06:18 ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ccc
06:18 scsi host0: ahci
06:18 scsi host1: ahci
06:18 scsi host2: ahci
06:18 ata1: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226100 irq 27
06:18 ata2: DUMMY
06:18 ata3: SATA max UDMA/133 abar m2048@0xfe226000 port 0xfe226200 irq 27
06:18 random: fast init done
06:18 scsi host3: ata_piix
06:18 scsi host4: ata_piix
06:18 ata4: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x1c00 irq 14
06:18 ata5: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x1c08 irq 15
06:18 libphy: Fixed MDIO Bus: probed
06:18 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
06:18 ehci-pci: EHCI PCI platform driver
06:18 ehci-pci 0000:00:1a.7: EHCI Host Controller
06:18 ehci-pci 0000:00:1a.7: new USB bus registered, assigned bus number 1
06:19 ehci-pci 0000:00:1a.7: irq 22, io mem 0xfe226c00
06:19 ACPI: Battery Slot [BAT0] (battery present)
06:19 ehci-pci 0000:00:1a.7: USB 2.0 started, EHCI 1.00
06:19 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
06:19 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb1: Product: EHCI Host Controller
06:19 usb usb1: Manufacturer: Linux 4.12.0-1.fc27.x86_64 ehci_hcd
06:19 usb usb1: SerialNumber: 0000:00:1a.7
06:19 hub 1-0:1.0: USB hub found
06:19 hub 1-0:1.0: 4 ports detected
06:19 ehci-pci 0000:00:1d.7: EHCI Host Controller
06:19 ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
06:19 ehci-pci 0000:00:1d.7: debug port 1
06:19 ehci-pci 0000:00:1d.7: irq 19, io mem 0xfe227000
06:19 ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
06:19 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
06:19 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb2: Product: EHCI Host Controller
06:19 usb usb2: Manufacturer: Linux 4.12.0-1.fc27.x86_64 ehci_hcd
06:19 usb usb2: SerialNumber: 0000:00:1d.7
06:19 hub 2-0:1.0: USB hub found
06:19 hub 2-0:1.0: 6 ports detected
06:19 ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
06:19 ohci-pci: OHCI PCI platform driver
06:19 uhci_hcd: USB Universal Host Controller Interface driver
06:19 uhci_hcd 0000:00:1a.0: UHCI Host Controller
06:19 uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
06:19 uhci_hcd 0000:00:1a.0: detected 2 ports
06:19 uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001860
06:19 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
06:19 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb3: Product: UHCI Host Controller
06:19 usb usb3: Manufacturer: Linux 4.12.0-1.fc27.x86_64 uhci_hcd
06:19 usb usb3: SerialNumber: 0000:00:1a.0
06:19 hub 3-0:1.0: USB hub found
06:19 hub 3-0:1.0: 2 ports detected
06:19 uhci_hcd 0000:00:1a.1: UHCI Host Controller
06:19 uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
06:19 uhci_hcd 0000:00:1a.1: detected 2 ports
06:19 uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001880
06:19 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
06:19 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb4: Product: UHCI Host Controller
06:19 usb usb4: Manufacturer: Linux 4.12.0-1.fc27.x86_64 uhci_hcd
06:19 usb usb4: SerialNumber: 0000:00:1a.1
06:19 hub 4-0:1.0: USB hub found
06:19 hub 4-0:1.0: 2 ports detected
06:19 uhci_hcd 0000:00:1d.0: UHCI Host Controller
06:19 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 5
06:19 uhci_hcd 0000:00:1d.0: detected 2 ports
06:19 uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018a0
06:19 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
06:19 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb5: Product: UHCI Host Controller
06:19 usb usb5: Manufacturer: Linux 4.12.0-1.fc27.x86_64 uhci_hcd
06:19 usb usb5: SerialNumber: 0000:00:1d.0
06:19 hub 5-0:1.0: USB hub found
06:19 hub 5-0:1.0: 2 ports detected
06:19 uhci_hcd 0000:00:1d.1: UHCI Host Controller
06:19 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 6
06:19 uhci_hcd 0000:00:1d.1: detected 2 ports
06:19 uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018c0
06:19 usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
06:19 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb6: Product: UHCI Host Controller
06:19 usb usb6: Manufacturer: Linux 4.12.0-1.fc27.x86_64 uhci_hcd
06:19 usb usb6: SerialNumber: 0000:00:1d.1
06:19 hub 6-0:1.0: USB hub found
06:19 hub 6-0:1.0: 2 ports detected
06:19 uhci_hcd 0000:00:1d.2: UHCI Host Controller
06:19 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
06:19 uhci_hcd 0000:00:1d.2: detected 2 ports
06:19 uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018e0
06:19 usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
06:19 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
06:19 usb usb7: Product: UHCI Host Controller
06:19 usb usb7: Manufacturer: Linux 4.12.0-1.fc27.x86_64 uhci_hcd
06:19 usb usb7: SerialNumber: 0000:00:1d.2
06:19 hub 7-0:1.0: USB hub found
06:19 hub 7-0:1.0: 2 ports detected
06:19 usbcore: registered new interface driver usbserial
06:19 usbcore: registered new interface driver usbserial_generic
06:19 usbserial: USB Serial support registered for generic
06:19 i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
06:19 serio: i8042 KBD port at 0x60,0x64 irq 1
06:19 serio: i8042 AUX port at 0x60,0x64 irq 12
06:19 mousedev: PS/2 mouse device common for all mice
06:19 rtc_cmos 00:02: RTC can wake from S4
06:19 rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
06:19 rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
06:19 device-mapper: uevent: version 1.0.3
06:19 device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@xxxxxxxxxx
06:19 hidraw: raw HID events driver (C) Jiri Kosina
06:19 usbcore: registered new interface driver usbhid
06:19 usbhid: USB HID core driver
06:19 drop_monitor: Initializing network drop monitor service
06:19 ip_tables: (C) 2000-2006 Netfilter Core Team
06:19 Initializing XFRM netlink socket
06:19 NET: Registered protocol family 10
06:19 Segment Routing with IPv6
06:19 mip6: Mobile IPv6
06:19 NET: Registered protocol family 17
06:19 input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
06:19 RAS: Correctable Errors collector initialized.
06:19 microcode: sig=0x6fa, pf=0x80, revision=0x95
06:19 microcode: Microcode Update Driver: v2.2.
06:19 registered taskstats version 1
06:19 Loading compiled-in X.509 certificates
06:19 alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-generic,sha256))
06:19 Loaded X.509 cert 'Fedora kernel signing key: afce39acf6b4e14fc753ae848b4302f3a65b72e0'
06:19 zswap: loaded using pool lzo/zbud
06:19 Key type big_key registered
06:19 Key type encrypted registered
06:19 Magic number: 9:783:140
06:19 acpi device:11: hash matches
06:19 rtc_cmos 00:02: setting system clock to 2017-07-24 18:06:18 UTC (1500919578)
06:19 ata4.00: ATAPI: MATSHITADVD-RAM UJ-842 z, RC01, max UDMA/33
06:19 ata4.00: configured for UDMA/33
06:19 ata3: SATA link down (SStatus 0 SControl 300)
06:19 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
06:19 ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
06:19 ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
06:19 ata1.00: ATA-9: SAMSUNG SSD 830 Series, CXM03B1Q, max UDMA/133
06:19 ata1.00: 500118192 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
06:19 ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
06:19 ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
06:19 ata1.00: configured for UDMA/133
06:19 scsi 0:0:0:0: Direct-Access ATA SAMSUNG SSD 830 3B1Q PQ: 0 ANSI: 5
06:19 sd 0:0:0:0: Attached scsi generic sg0 type 0
06:19 sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
06:19 sd 0:0:0:0: [sda] Write Protect is off
06:19 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
06:19 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
06:19 scsi 3:0:0:0: CD-ROM MATSHITA DVD-RAM UJ-842 z RC01 PQ: 0 ANSI: 5
06:19 sd 0:0:0:0: [sda] Attached SCSI disk
06:19 usb 2-2: new high-speed USB device number 2 using ehci-pci
06:19 sr 3:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
06:19 cdrom: Uniform CD-ROM driver Revision: 3.20
06:19 sr 3:0:0:0: Attached scsi generic sg1 type 5
06:19 Freeing unused kernel memory: 2164K
06:19 Write protecting the kernel read-only data: 14336k
06:19 Freeing unused kernel memory: 1532K
06:19 Freeing unused kernel memory: 404K
06:19 x86/mm: Checked W+X mappings: passed, no W+X pages found.
06:19 rodata_test: all tests were successful
06:19[1]: Starting Create list of required static device nodes for the current kernel...
06:19 kernel profiling enabled schedstats, disable via kernel.sched_schedstats.
06:19 usb 2-2: New USB device found, idVendor=1058, idProduct=10a8
06:19 usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
06:19 usb 2-2: Product: Elements 10A8
06:19 usb 2-2: Manufacturer: Western Digital
06:19 usb 2-2: SerialNumber: 5758333145373354504C3031
06:19 usb-storage 2-2:1.0: USB Mass Storage device detected
06:19 scsi host5: usb-storage 2-2:1.0
06:19 usbcore: registered new interface driver usb-storage
06:19 usbcore: registered new interface driver uas
06:19 usb 3-2: new full-speed USB device number 2 using uhci_hcd
06:19 usb 3-2: New USB device found, idVendor=0483, idProduct=2016
06:19 usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
06:19 usb 3-2: Product: Biometric Coprocessor
06:19 usb 3-2: Manufacturer: STMicroelectronics
06:19 psmouse serio1: synaptics: Touchpad model: 1, fw: 6.2, id: 0x81a0b1, caps: 0xa04791/0x300000/0x0/0x0, board id: 0, fw id: 496542
06:19 psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
06:19 pci 0000:00:1e.0: enabling device (0005 -> 0007)
06:19 yenta_cardbus 0000:15:00.0: CardBus bridge found [17aa:20c6]
06:19 sdhci: Secure Digital Host Controller Interface driver
06:19 sdhci: Copyright(c) Pierre Ossman
06:19 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
06:19 yenta_cardbus 0000:15:00.0: ISA IRQ mask 0x0cb8, PCI irq 16
06:19 yenta_cardbus 0000:15:00.0: Socket status: 30000006
06:19 yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge window: [io 0x6000-0x9fff]
06:19 yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge window: [mem 0xf8300000-0xfbffffff]
06:19 pcmcia_socket pcmcia_socket0: cs: memory probe 0xf8300000-0xfbffffff:
06:19 excluding 0xf8300000-0xf86cffff
06:19 yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge window: [mem 0xf4000000-0xf7ffffff 64bit pref]
06:19 pcmcia_socket pcmcia_socket0: cs: memory probe 0xf4000000-0xf7ffffff:
06:19 excluding 0xf4000000-0xf7ffffff
06:19 sdhci-pci 0000:15:00.2: SDHCI controller found [1180:0822] (rev 21)
06:19 sdhci-pci 0000:15:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
06:19 sdhci-pci 0000:15:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
06:19 mmc0: SDHCI controller on PCI [0000:15:00.2] using DMA
06:19 EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
06:19 pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
06:19 excluding 0xc0000-0xcffff 0xe0000-0xfffff
06:19 pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
06:19 excluding 0xa0000000-0xa0ffffff
06:19 pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
06:19 excluding 0x60000000-0x60ffffff
06:19 pci 0000:00:00.0: Intel 965GM Chipset
06:19 pci 0000:00:00.0: detected gtt size: 524288K total, 262144K mappable
06:19 pci 0000:00:00.0: detected 8192K stolen memory
06:19 [drm] Memory usable by graphics device = 512M
06:19 [drm] Replacing VGA console driver
06:19 Console: switching to colour dummy device 80x25
06:19 [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
06:19 [drm] Driver supports precise vblank timestamp query.
06:19 i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
06:19 mmc0: new high speed SDHC card at address aaaa
06:19 [drm] RC6 disabled, disabling runtime PM support
06:19 [drm] initialized overlay support
06:19 [drm] Initialized i915 1.6.0 20170403 for 0000:00:02.0 on minor 0
06:19 ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
06:19 input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input7
06:20 fbcon: inteldrmfb (fb0) is primary device
06:20 scsi 5:0:0:0: Direct-Access WD Elements 10A8 1042 PQ: 0 ANSI: 6
06:20 sd 5:0:0:0: Attached scsi generic sg2 type 0
06:20 sd 5:0:0:0: [sdb] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
06:20 sd 5:0:0:0: [sdb] Write Protect is off
06:20 sd 5:0:0:0: [sdb] No Caching mode page found
06:20 sd 5:0:0:0: [sdb] Assuming drive cache: write through
06:20 sdb: sdb1 sdb2
06:20 sd 5:0:0:0: [sdb] Attached SCSI disk
06:20 psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
06:20 input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input6
06:20 Console: switching to colour frame buffer device 210x65
06:20 i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
06:20 systemd: 73 output lines suppressed due to ratelimiting
06:20 EXT4-fs (sda2): re-mounted. Opts: data=ordered
06:20 loop: module loaded
06:20 RPC: Registered named UNIX socket transport module.
06:20 RPC: Registered udp transport module.
06:20 RPC: Registered tcp transport module.
06:20 RPC: Registered tcp NFSv4.1 backchannel transport module.
06:21 Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
06:21 wmi: Mapper loaded
06:21 pps_core: LinuxPPS API ver. 1 registered
06:21 pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
06:21 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
06:21 PTP clock support registered
06:21 thinkpad_acpi: ThinkPad ACPI Extras v0.25
06:21 thinkpad_acpi: http://ibm-acpi.sf.net/
06:21 thinkpad_acpi: ThinkPad BIOS 7LETC9WW (2.29 ), EC 7KHT24WW-1.08
06:21 thinkpad_acpi: Lenovo ThinkPad T61, model 6464CTO
06:21 mmcblk0: mmc0:aaaa SL32G 29.7 GiB
06:21 mmcblk0: p1
06:21 pcmcia_socket pcmcia_socket0: cs: memory probe 0x0c0000-0x0fffff:
06:21 ACPI Warning: SystemIO range 0x0000000000001028-0x000000000000102F conflicts with OpRegion 0x0000000000001000-0x000000000000107F (\_SB.PCI0.LPC.PMIO) (20170303/utaddress-247)
06:21 ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
06:21 excluding 0xc0000-0xcffff 0xe0000-0xfffff
06:21 pcmcia_socket pcmcia_socket0: cs: memory probe 0xa0000000-0xa0ffffff:
06:21 excluding 0xa0000000-0xa0ffffff
06:21 pcmcia_socket pcmcia_socket0: cs: memory probe 0x60000000-0x60ffffff:
06:21 excluding 0x60000000-0x60ffffff
06:21 thinkpad_hwmon thinkpad_hwmon: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
06:21 thinkpad_acpi: ACPI backlight control delay disabled
06:21 thinkpad_acpi: radio switch found; radios are enabled
06:21 r592: driver successfully loaded
06:21 e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
06:21 e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
06:21 random: crng init done
06:21 ACPI Warning: SystemIO range 0x00000000000011B0-0x00000000000011BF conflicts with OpRegion 0x0000000000001180-0x00000000000011BF (\_SB.PCI0.LPC.LPIO) (20170303/utaddress-247)
06:21 ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
06:21 ACPI Warning: SystemIO range 0x0000000000001180-0x00000000000011AF conflicts with OpRegion 0x0000000000001180-0x00000000000011BF (\_SB.PCI0.LPC.LPIO) (20170303/utaddress-247)
06:21 ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
06:21 thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is blocked
06:21 lpc_ich: Resource conflict(s) found affecting gpio_ich
06:21 thinkpad_acpi: Standard ACPI backlight interface not available, thinkpad_acpi native brightness control enabled
06:21 input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input8
06:21 e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
06:21 iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, in-tree:ds
06:21 iwl3945: Copyright(c) 2003-2011 Intel Corporation
06:21 iwl3945: hw_scan is disabled
06:21 iwl3945 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
06:22 iwl3945 0000:03:00.0: Tunable channels: 13 802.11bg, 23 802.11a channels
06:22 iwl3945 0000:03:00.0: Detected Intel Wireless WiFi Link 3945ABG
06:22 ppdev: user-space parallel port driver
06:22 iTCO_vendor_support: vendor-support=0
06:22 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
06:22 iTCO_wdt: Found a ICH8M-E TCO device (Version=2, TCOBASE=0x1060)
06:22 iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
06:22 intel_powerclamp: No package C-state available
06:22 e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:1c:25:14:4a:e2
06:22 e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
06:22 e1000e 0000:00:19.0 eth0: MAC: 6, PHY: 6, PBA No: FFFFFF-0FF
06:22 i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
06:22 snd_hda_intel 0000:00:1b.0: probe_mask set to 0x1 for device 17aa:20ac
06:22 snd_hda_codec_analog hdaudioC0D0: autoconfig for AD1984: line_outs=1 (0x12/0x0/0x0/0x0/0x0) type:speaker
06:22 snd_hda_codec_analog hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
06:22 snd_hda_codec_analog hdaudioC0D0: hp_outs=1 (0x11/0x0/0x0/0x0/0x0)
06:22 snd_hda_codec_analog hdaudioC0D0: mono: mono_out=0x0
06:22 snd_hda_codec_analog hdaudioC0D0: dig-out=0x1b/0x0
06:22 snd_hda_codec_analog hdaudioC0D0: inputs:
06:22 snd_hda_codec_analog hdaudioC0D0: Internal Mic=0x15
06:22 snd_hda_codec_analog hdaudioC0D0: Mic=0x14
06:22 EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: data=ordered
06:22 snd_hda_codec_analog hdaudioC0D0: Dock Mic=0x1c
06:22 EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: data=ordered,user_xattr
06:22 input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
06:22 input: HDA Intel Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
06:22 input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
06:24 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
06:24 IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
06:24 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
06:24 iwl3945 0000:03:00.0: loaded firmware version 15.32.2.9
06:24 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
06:24 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
06:24 ip6_tables: (C) 2000-2006 Netfilter Core Team
06:24 Ebtables v2.0 registered
06:25 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
06:25 bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
06:25 tun: Universal TUN/TAP device driver, 1.6
06:25 virbr0: port 1(virbr0-nic) entered blocking state
06:25 virbr0: port 1(virbr0-nic) entered disabled state
06:25 device virbr0-nic entered promiscuous mode
06:25 nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
06:25 virbr0: port 1(virbr0-nic) entered blocking state
06:25 virbr0: port 1(virbr0-nic) entered listening state
06:25 virbr0: port 1(virbr0-nic) entered disabled state
06:28 IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
06:32 wlan0: associated
06:32 IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
06:32 NFSD: starting 90-second grace period (net ffffffff8afe0240)
06:42 EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
06:48 usb 2-2: USB disconnect, device number 2
06:55 usb 2-2: new high-speed USB device number 3 using ehci-pci
06:55 usb 5-2: new full-speed USB device number 2 using uhci_hcd
06:56 usb 5-2: not running at top speed; connect to a high speed hub
06:56 usb 5-2: New USB device found, idVendor=1058, idProduct=10a8
06:56 usb 5-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
06:56 usb 5-2: Product: Elements 10A8
06:56 usb 5-2: Manufacturer: Western Digital
06:56 usb 5-2: SerialNumber: 5758333145373354504C3031
06:56 usb-storage 5-2:1.0: USB Mass Storage device detected
06:56 scsi host5: usb-storage 5-2:1.0
06:57 scsi 5:0:0:0: Direct-Access WD Elements 10A8 1042 PQ: 0 ANSI: 6
06:57 sd 5:0:0:0: Attached scsi generic sg2 type 0
06:57 sd 5:0:0:0: [sdb] Spinning up disk...
06:59 .
07:00 .
07:01 .
07:01 .
07:01 ready
07:01 sd 5:0:0:0: [sdb] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
07:01 sd 5:0:0:0: [sdb] Write Protect is off
07:01 sd 5:0:0:0: [sdb] No Caching mode page found
07:01 sd 5:0:0:0: [sdb] Assuming drive cache: write through
07:01 sdb: sdb1 sdb2
07:01 sd 5:0:0:0: [sdb] Attached SCSI disk
07:08 EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
07:27 nfsd: last server has exited, flushing export cache
04:50 microcode: microcode updated early to revision 0x20, date = 2017-01-27
04:50 random: get_random_bytes called from start_kernel+0x42/0x4e6 with crng_init=0
04:50 Linux version 4.13.0-0.rc1.git3.2.fc27.x86_64 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 7.1.1 20170718 (Red Hat 7.1.1-6) (GCC)) #1 SMP Thu Jul 20 22:05:05 UTC 2017
04:50 Command line: BOOT_IMAGE=/vmlinuz-4.13.0-0.rc1.git3.2.fc27.x86_64 root=UUID=3756a4b4-a65d-48d3-85e3-286d101cd4b8 ro vconsole.font=latarcyrheb-sun16 rhgb selinux=0 quiet LANG=cs_CZ.UTF-8
04:50 x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
04:50 x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
04:50 x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
04:50 x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
04:50 x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
04:50 e820: BIOS-provided physical RAM map:
04:50 BIOS-e820: [mem 0x0000000000000000-0x000000000009cfff] usable
04:50 BIOS-e820: [mem 0x000000000009d000-0x000000000009ffff] reserved
04:50 BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
04:50 BIOS-e820: [mem 0x0000000000100000-0x00000000ce21dfff] usable
04:50 BIOS-e820: [mem 0x00000000ce21e000-0x00000000dcd3efff] reserved
04:50 BIOS-e820: [mem 0x00000000dcd3f000-0x00000000dce7efff] ACPI NVS
04:50 BIOS-e820: [mem 0x00000000dce7f000-0x00000000dcefefff] ACPI data
04:50 BIOS-e820: [mem 0x00000000dceff000-0x00000000df9fffff] reserved
04:50 BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
04:50 BIOS-e820: [mem 0x00000000fe101000-0x00000000fe112fff] reserved
04:50 BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
04:50 BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
04:50 BIOS-e820: [mem 0x00000000fed10000-0x00000000fed19fff] reserved
04:50 BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
04:50 BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
04:50 BIOS-e820: [mem 0x00000000ffc00000-0x00000000ffffffff] reserved
04:50 BIOS-e820: [mem 0x0000000100000000-0x000000021e5fffff] usable
04:50 NX (Execute Disable) protection: active
04:50 random: fast init done
04:50 SMBIOS 2.7 present.
04:50 DMI: LENOVO 20AQ0069GE/20AQ0069GE, BIOS GJET67WW (2.17 ) 12/10/2013
04:50 tsc: Fast TSC calibration using PIT
04:50 e820: last_pfn = 0x21e600 max_arch_pfn = 0x400000000
04:50 x86/PAT: Configuration [0-7]: WB WC UC- UC WB WC UC- WT
04:50 e820: last_pfn = 0xce21e max_arch_pfn = 0x400000000
04:50 found SMP MP-table at [mem 0x000f0100-0x000f010f] mapped at [ffff9996400f0100]
04:50 Using GB pages for direct mapping
04:50 RAMDISK: [mem 0x35925000-0x36c8afff]
04:50 ACPI: Early table checksum verification disabled
04:50 ACPI: RSDP 0x00000000000F0120 000024 (v02 LENOVO)
04:50 ACPI: XSDT 0x00000000DCEFE170 0000F4 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: FACP 0x00000000DCEF8000 00010C (v05 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: DSDT 0x00000000DCEE2000 010E6D (v01 LENOVO TP-GJ 00002170 INTL 20120711)
04:50 ACPI: FACS 0x00000000DCE4A000 000040
04:50 ACPI: SLIC 0x00000000DCEFD000 000176 (v01 LENOVO TP-GJ 00002170 PTEC 00000001)
04:50 ACPI: DBGP 0x00000000DCEFB000 000034 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: ECDT 0x00000000DCEFA000 000052 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: HPET 0x00000000DCEF7000 000038 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: APIC 0x00000000DCEF6000 000098 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: MCFG 0x00000000DCEF5000 00003C (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: SSDT 0x00000000DCEF4000 000033 (v01 LENOVO TP-SSDT1 00000100 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEF3000 00044F (v01 LENOVO TP-SSDT2 00000200 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEE1000 0009CB (v01 LENOVO SataAhci 00001000 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEE0000 000152 (v01 LENOVO Rmv_Batt 00001000 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEDF000 0007F5 (v01 LENOVO Cpu0Ist 00003000 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEDE000 000AD8 (v01 LENOVO CpuPm 00003000 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEDC000 001215 (v01 LENOVO SaSsdt 00003000 INTL 20120711)
04:50 ACPI: SSDT 0x00000000DCEDB000 000379 (v01 LENOVO CppcTabl 00001000 INTL 20120711)
04:50 ACPI: PCCT 0x00000000DCEDA000 00006E (v05 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: SSDT 0x00000000DCED9000 000AC4 (v01 LENOVO Cpc_Tabl 00001000 INTL 20120711)
04:50 ACPI: TCPA 0x00000000DCED8000 000032 (v02 PTL LENOVO 06040000 LNVO 00000001)
04:50 ACPI: UEFI 0x00000000DCED7000 000042 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: MSDM 0x00000000DCDB2000 000055 (v03 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: ASF! 0x00000000DCEFC000 0000A5 (v32 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: BATB 0x00000000DCED6000 000046 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: FPDT 0x00000000DCED5000 000064 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: UEFI 0x00000000DCED4000 0002E2 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 ACPI: SSDT 0x00000000DCED3000 00047F (v01 LENOVO IsctTabl 00001000 INTL 20120711)
04:50 ACPI: DMAR 0x00000000DCED2000 0000B0 (v01 LENOVO TP-GJ 00002170 PTEC 00000002)
04:50 No NUMA configuration found
04:50 Faking a node at [mem 0x0000000000000000-0x000000021e5fffff]
04:50 NODE_DATA(0) allocated [mem 0x21e5d3000-0x21e5fdfff]
04:50 Zone ranges:
04:50 DMA [mem 0x0000000000001000-0x0000000000ffffff]
04:50 DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
04:50 Normal [mem 0x0000000100000000-0x000000021e5fffff]
04:50 Device empty
04:50 Movable zone start for each node
04:50 Early memory node ranges
04:50 node 0: [mem 0x0000000000001000-0x000000000009cfff]
04:50 node 0: [mem 0x0000000000100000-0x00000000ce21dfff]
04:50 node 0: [mem 0x0000000100000000-0x000000021e5fffff]
04:50 Initmem setup node 0 [mem 0x0000000000001000-0x000000021e5fffff]
04:50 Reserving Intel graphics memory at 0x00000000dda00000-0x00000000df9fffff
04:50 ACPI: PM-Timer IO Port: 0x1808
04:50 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
04:50 ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
04:50 IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-39
04:50 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
04:50 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
04:50 Using ACPI (MADT) for SMP configuration information
04:50 ACPI: HPET id: 0x8086a301 base: 0xfed00000
04:50 smpboot: Allowing 8 CPUs, 4 hotplug CPUs
04:50 PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
04:50 PM: Registered nosave memory: [mem 0x0009d000-0x0009ffff]
04:50 PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
04:50 PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
04:50 PM: Registered nosave memory: [mem 0xce21e000-0xdcd3efff]
04:50 PM: Registered nosave memory: [mem 0xdcd3f000-0xdce7efff]
04:50 PM: Registered nosave memory: [mem 0xdce7f000-0xdcefefff]
04:50 PM: Registered nosave memory: [mem 0xdceff000-0xdf9fffff]
04:50 PM: Registered nosave memory: [mem 0xdfa00000-0xf7ffffff]
04:50 PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
04:50 PM: Registered nosave memory: [mem 0xfc000000-0xfe100fff]
04:50 PM: Registered nosave memory: [mem 0xfe101000-0xfe112fff]
04:50 PM: Registered nosave memory: [mem 0xfe113000-0xfebfffff]
04:50 PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
04:50 PM: Registered nosave memory: [mem 0xfec01000-0xfed07fff]
04:50 PM: Registered nosave memory: [mem 0xfed08000-0xfed08fff]
04:50 PM: Registered nosave memory: [mem 0xfed09000-0xfed0ffff]
04:50 PM: Registered nosave memory: [mem 0xfed10000-0xfed19fff]
04:50 PM: Registered nosave memory: [mem 0xfed1a000-0xfed1bfff]
04:50 PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
04:50 PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
04:50 PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
04:50 PM: Registered nosave memory: [mem 0xfee01000-0xffbfffff]
04:50 PM: Registered nosave memory: [mem 0xffc00000-0xffffffff]
04:50 e820: [mem 0xdfa00000-0xf7ffffff] available for PCI devices
04:50 Booting paravirtualized kernel on bare hardware
04:50 clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
04:50 setup_percpu: NR_CPUS:8192 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
04:50 percpu: Embedded 37 pages/cpu @ffff99985e200000 s112600 r8192 d30760 u262144
04:50 Built 1 zonelists in Node order, mobility grouping on. Total pages: 1985668
04:50 Policy zone: Normal
04:50 Kernel command line: BOOT_IMAGE=/vmlinuz-4.13.0-0.rc1.git3.2.fc27.x86_64 root=UUID=3756a4b4-a65d-48d3-85e3-286d101cd4b8 ro vconsole.font=latarcyrheb-sun16 rhgb selinux=0 quiet LANG=cs_CZ.UTF-8
04:50 PID hash table entries: 4096 (order: 3, 32768 bytes)
04:50 Memory: 7833416K/8068840K available (8821K kernel code, 2403K rwdata, 3756K rodata, 2220K init, 1976K bss, 235424K reserved, 0K cma-reserved)
04:50 SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
04:50 ftrace: allocating 34860 entries in 137 pages
04:50 Hierarchical RCU implementation.
04:50 #011RCU restricting CPUs from NR_CPUS=8192 to nr_cpu_ids=8.
04:50 #011Tasks RCU enabled.
04:50 RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=8
04:50 NR_IRQS: 524544, nr_irqs: 760, preallocated irqs: 16
04:50 #011Offload RCU callbacks from CPUs: .
04:50 Console: colour VGA+ 80x25
04:50 console [tty0] enabled
04:50 clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
04:50 tsc: Fast TSC calibration using PIT
04:50 tsc: Detected 2693.743 MHz processor
04:50 Calibrating delay loop (skipped), value calculated using timer frequency.. 5387.48 BogoMIPS (lpj=2693743)
04:50 pid_max: default: 32768 minimum: 301
04:50 ACPI: Core revision 20170531
04:50 ACPI: 11 ACPI AML tables successfully acquired and loaded
04:50 Security Framework initialized
04:50 Yama: becoming mindful.
04:50 SELinux: Disabled at boot.
04:50 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
04:50 Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
04:50 Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
04:50 Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes)
04:50 CPU: Physical Processor ID: 0
04:50 CPU: Processor Core ID: 0
04:50 ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
04:50 ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
04:50 mce: CPU supports 7 MCE banks
04:50 CPU0: Thermal monitoring enabled (TM1)
04:50 process: using mwait in idle threads
04:50 Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
04:50 Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
04:50 Freeing SMP alternatives memory: 32K
04:50 smpboot: Max logical packages: 4
04:50 DMAR: Host address width 39
04:50 DMAR: DRHD base: 0x000000fed90000 flags: 0x0
04:50 DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap c0000020660462 ecap f0101a
04:50 DMAR: DRHD base: 0x000000fed91000 flags: 0x1
04:50 DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008020660462 ecap f010da
04:50 DMAR: RMRR base: 0x000000daed3000 end: 0x000000daee9fff
04:50 DMAR: RMRR base: 0x000000dd800000 end: 0x000000df9fffff
04:50 DMAR-IR: IOAPIC id 2 under DRHD base 0xfed91000 IOMMU 1
04:50 DMAR-IR: HPET id 0 under DRHD base 0xfed91000
04:50 DMAR-IR: Queued invalidation will be enabled to support x2apic and Intr-remapping.
04:50 DMAR-IR: Enabled IRQ remapping in x2apic mode
04:50 x2apic enabled
04:50 Switched APIC routing to cluster x2apic.
04:50 ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
04:50 smpboot: CPU0: Intel(R) Core(TM) i7-4600U CPU @ 2.10GHz (family: 0x6, model: 0x45, stepping: 0x1)
04:50 Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR, full-width counters, Intel PMU driver.
04:50 ... version: 3
04:50 ... bit width: 48
04:50 ... generic registers: 4
04:50 ... value mask: 0000ffffffffffff
04:50 ... max period: 00007fffffffffff
04:50 ... fixed-purpose events: 3
04:50 ... event mask: 000000070000000f
04:50 Hierarchical SRCU implementation.
04:50 NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
04:50 smp: Bringing up secondary CPUs ...
04:50 x86: Booting SMP configuration:
04:50 .... node #0, CPUs: #1 #2 #3
04:50 smp: Brought up 1 node, 4 CPUs
04:50 smpboot: Total of 4 processors activated (21571.00 BogoMIPS)
04:50 devtmpfs: initialized
04:50 x86/mm: Memory block size: 128MB
04:50 PM: Registering ACPI NVS region [mem 0xdcd3f000-0xdce7efff] (1310720 bytes)
04:50 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
04:50 futex hash table entries: 2048 (order: 5, 131072 bytes)
04:50 pinctrl core: initialized pinctrl subsystem
04:50 RTC time: 17:04:49, date: 07/24/17
04:50 NET: Registered protocol family 16
04:50 cpuidle: using governor menu
04:50 Error parsing PCC subspaces from PCCT
04:50 ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
04:50 ACPI: bus type PCI registered
04:50 acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
04:50 PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem 0xf8000000-0xfbffffff] (base 0xf8000000)
04:50 PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
04:50 PCI: Using configuration type 1 for base access
04:50 core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
04:50 HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
04:50 HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
04:50 ACPI: Added _OSI(Module Device)
04:50 ACPI: Added _OSI(Processor Device)
04:50 ACPI: Added _OSI(3.0 _SCP Extensions)
04:50 ACPI: Added _OSI(Processor Aggregator Device)
04:50 ACPI: EC: EC started
04:50 ACPI: EC: interrupt blocked
04:50 ACPI: \: Used as first EC
04:50 ACPI: \: GPE=0x25, EC_CMD/EC_SC=0x66, EC_DATA=0x62
04:50 ACPI: \: Used as boot ECDT EC to handle transactions
04:50 ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
04:50 ACPI Error: Needed type [Reference], found [Integer] ffff9998545573a8 (20170531/exresop-103)
04:50 ACPI Exception: AE_AML_OPERAND_TYPE, While resolving operands for [OpcodeName unavailable] (20170531/dswexec-461)
04:50 ACPI Error: Method parse/execution failed \_PR.CPU0._PDC, AE_AML_OPERAND_TYPE (20170531/psparse-550)
04:50 ACPI: Dynamic OEM Table Load:
04:50 ACPI: SSDT 0xFFFF999854B60000 0005AA (v01 PmRef ApIst 00003000 INTL 20120711)
04:50 ACPI: Dynamic OEM Table Load:
04:50 ACPI: SSDT 0xFFFF999854530C00 000119 (v01 PmRef ApCst 00003000 INTL 20120711)
04:50 ACPI: Interpreter enabled
04:50 ACPI: (supports S0 S3 S4 S5)
04:50 ACPI: Using IOAPIC for interrupt routing
04:50 PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
04:50 ACPI: Power Resource [PUBS] (on)
04:50 acpi PNP0C0A:01: ACPI dock station (docks/bays count: 1)
04:50 ACPI: Power Resource [NVP3] (on)
04:50 ACPI: Power Resource [NVP2] (on)
04:50 ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
04:50 ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11)
04:50 ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 *10 11)
04:50 ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 9 10 11)
04:50 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
04:50 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled.
04:50 ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11)
04:50 ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 *7 9 10 11)
04:50 ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3f])
04:50 acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI]
04:50 acpi PNP0A08:00: _OSC: platform does not support [PCIeCapability]
04:50 acpi PNP0A08:00: _OSC: not requesting control; platform does not support [PCIeCapability]
04:50 acpi PNP0A08:00: _OSC: OS requested [PCIeHotplug PME AER PCIeCapability]
04:50 acpi PNP0A08:00: _OSC: platform willing to grant [PCIeHotplug PME AER]
04:50 acpi PNP0A08:00: _OSC failed (AE_SUPPORT); disabling ASPM
04:50 PCI host bridge to bus 0000:00
04:50 pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
04:50 pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
04:50 pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
04:50 pci_bus 0000:00: root bus resource [mem 0xdfa00000-0xfebfffff window]
04:50 pci_bus 0000:00: root bus resource [mem 0xfed40000-0xfed4bfff window]
04:50 pci_bus 0000:00: root bus resource [bus 00-3f]
04:50 pci 0000:00:1c.0: PCI bridge to [bus 02]
04:50 pci 0000:00:1c.1: PCI bridge to [bus 03]
04:50 ACPI: Enabled 4 GPEs in block 00 to 7F
04:50 ACPI: EC: EC stopped
04:50 ACPI: EC: EC started
04:50 ACPI: EC: interrupt blocked
04:50 ACPI: EC: interrupt unblocked
04:50 ACPI: EC: event unblocked
04:50 ACPI: \_SB_.PCI0.LPC_.EC__: GPE=0x25, EC_CMD/EC_SC=0x66, EC_DATA=0x62
04:50 ACPI: \_SB_.PCI0.LPC_.EC__: Used as boot ECDT EC to handle transactions and events
04:50 ACPI: \_SB_.PCI0.LPC_.EC__: GPE=0x25, EC_CMD/EC_SC=0x66, EC_DATA=0x62
04:50 ACPI: \_SB_.PCI0.LPC_.EC__: Used as boot DSDT EC to handle transactions and events
04:50 pci 0000:00:02.0: vgaarb: setting as boot VGA device
04:50 pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
04:50 pci 0000:00:02.0: vgaarb: bridge control possible
04:50 vgaarb: loaded
04:50 SCSI subsystem initialized
04:50 ACPI: bus type USB registered
04:50 usbcore: registered new interface driver usbfs
04:50 usbcore: registered new interface driver hub
04:50 usbcore: registered new device driver usb
04:50 EDAC MC: Ver: 3.0.0
04:50 PCI: Using ACPI for IRQ routing
04:50 NetLabel: Initializing
04:50 NetLabel: domain hash size = 128
04:50 NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
04:50 NetLabel: unlabeled traffic allowed by default
04:50 hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
04:50 hpet0: 8 comparators, 64-bit 14.318180 MHz counter
04:50 clocksource: Switched to clocksource hpet
04:50 VFS: Disk quotas dquot_6.6.0
04:50 VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
04:50 pnp: PnP ACPI init
04:50 system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved
04:50 system 00:00: [mem 0x000c0000-0x000c3fff] could not be reserved
04:50 system 00:00: [mem 0x000c4000-0x000c7fff] could not be reserved
04:50 system 00:00: [mem 0x000c8000-0x000cbfff] could not be reserved
04:50 system 00:00: [mem 0x000cc000-0x000cffff] could not be reserved
04:50 system 00:00: [mem 0x000d0000-0x000d3fff] has been reserved
04:50 system 00:00: [mem 0x000d4000-0x000d7fff] has been reserved
04:50 system 00:00: [mem 0x000d8000-0x000dbfff] has been reserved
04:50 system 00:00: [mem 0x000dc000-0x000dffff] has been reserved
04:50 system 00:00: [mem 0x000e0000-0x000e3fff] could not be reserved
04:50 system 00:00: [mem 0x000e4000-0x000e7fff] could not be reserved
04:50 system 00:00: [mem 0x000e8000-0x000ebfff] could not be reserved
04:50 system 00:00: [mem 0x000ec000-0x000effff] could not be reserved
04:50 system 00:00: [mem 0x000f0000-0x000fffff] could not be reserved
04:50 system 00:00: [mem 0x00100000-0xdf9fffff] could not be reserved
04:50 system 00:00: [mem 0xfec00000-0xfed3ffff] could not be reserved
04:50 system 00:00: [mem 0xfed4c000-0xffffffff] could not be reserved
04:50 pnp 00:01: [Firmware Bug]: PNP resource [mem 0xfed10000-0xfed13fff] covers only part of 0000:00:00.0 Intel MCH; extending to [mem 0xfed10000-0xfed17fff]
04:50 system 00:01: [io 0x1800-0x189f] has been reserved
04:50 system 00:01: [io 0x0800-0x087f] has been reserved
04:50 system 00:01: [io 0x0880-0x08ff] has been reserved
04:50 system 00:01: [io 0x0900-0x097f] has been reserved
04:50 system 00:01: [io 0x0980-0x09ff] has been reserved
04:50 system 00:01: [io 0x0a00-0x0a7f] has been reserved
04:50 system 00:01: [io 0x0a80-0x0aff] has been reserved
04:50 system 00:01: [io 0x0b00-0x0b7f] has been reserved
04:50 system 00:01: [io 0x0b80-0x0bff] has been reserved
04:50 system 00:01: [io 0x15e0-0x15ef] has been reserved
04:50 system 00:01: [io 0x1600-0x167f] has been reserved
04:50 system 00:01: [io 0x1640-0x165f] has been reserved
04:50 system 00:01: [mem 0xf8000000-0xfbffffff] has been reserved
04:50 system 00:01: [mem 0x00000000-0x00000fff] could not be reserved
04:50 system 00:01: [mem 0xfed1c000-0xfed1ffff] has been reserved
04:50 system 00:01: [mem 0xfed10000-0xfed17fff] has been reserved
04:50 system 00:01: [mem 0xfed18000-0xfed18fff] has been reserved
04:50 system 00:01: [mem 0xfed19000-0xfed19fff] has been reserved
04:50 system 00:01: [mem 0xfed45000-0xfed4bfff] has been reserved
04:50 pnp: PnP ACPI: found 6 devices
04:50 clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
04:50 pci 0000:00:1c.0: PCI bridge to [bus 02]
04:50 pci 0000:00:1c.0: bridge window [mem 0xf0500000-0xf05fffff]
04:50 pci 0000:00:1c.1: PCI bridge to [bus 03]
04:50 pci 0000:00:1c.1: bridge window [mem 0xf0400000-0xf04fffff]
04:50 NET: Registered protocol family 2
04:50 TCP established hash table entries: 65536 (order: 7, 524288 bytes)
04:50 TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
04:50 TCP: Hash tables configured (established 65536 bind 65536)
04:50 UDP hash table entries: 4096 (order: 5, 131072 bytes)
04:50 UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
04:50 NET: Registered protocol family 1
04:50 pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
04:50 Unpacking initramfs...
04:50 Freeing initrd memory: 19864K
04:50 PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
04:50 software IO TLB [mem 0xca21e000-0xce21e000] (64MB) mapped at [ffff99970a21e000-ffff99970e21dfff]
04:50 audit: initializing netlink subsys (disabled)
04:50 audit: type=2000 audit(1500915889.619:1): state=initialized audit_enabled=0 res=1
04:50 Initialise system trusted keyrings
04:50 Key type blacklist registered
04:50 workingset: timestamp_bits=36 max_order=21 bucket_order=0
04:50 zbud: loaded
04:50 NET: Registered protocol family 38
04:50 Key type asymmetric registered
04:50 Asymmetric key parser 'x509' registered
04:50 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
04:50 io scheduler noop registered
04:50 io scheduler deadline registered
04:50 io scheduler cfq registered (default)
04:50 io scheduler mq-deadline registered
04:50 atomic64_test: passed for x86-64 platform with CX8 and with SSE
04:50 ACPI: AC Adapter [AC] (on-line)
04:50 input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input0
04:50 ACPI: Lid Switch [LID]
04:50 input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
04:50 ACPI: Sleep Button [SLPB]
04:50 input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
04:50 ACPI: Power Button [PWRF]
04:50 (NULL device *): hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
04:50 thermal LNXTHERM:00: registered as thermal_zone0
04:50 ACPI: Thermal Zone [THM0] (48 C)
04:50 GHES: HEST is not enabled!
04:50 Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
04:50 Non-volatile memory driver v1.3
04:50 Linux agpgart interface v0.103
04:50 ACPI: Battery Slot [BAT0] (battery present)
04:50 ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x1 impl SATA mode
04:50 ahci 0000:00:1f.2: flags: 64bit ncq pm led clo only pio slum part deso sadm sds apst
04:50 scsi host0: ahci
04:50 scsi host1: ahci
04:50 scsi host2: ahci
04:50 ata1: SATA max UDMA/133 abar m2048@0xf063c000 port 0xf063c100 irq 42
04:50 ata2: DUMMY
04:50 ata3: DUMMY
04:50 libphy: Fixed MDIO Bus: probed
04:50 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
04:50 ehci-pci: EHCI PCI platform driver
04:50 ehci-pci 0000:00:1d.0: EHCI Host Controller
04:50 ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 1
04:50 ehci-pci 0000:00:1d.0: debug port 2
04:50 ACPI: Battery Slot [BAT1] (battery present)
04:50 ehci-pci 0000:00:1d.0: irq 23, io mem 0xf063d000
04:50 ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
04:50 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
04:50 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
04:50 usb usb1: Product: EHCI Host Controller
04:50 usb usb1: Manufacturer: Linux 4.13.0-0.rc1.git3.2.fc27.x86_64 ehci_hcd
04:50 usb usb1: SerialNumber: 0000:00:1d.0
04:50 hub 1-0:1.0: USB hub found
04:50 hub 1-0:1.0: 3 ports detected
04:50 ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
04:50 ohci-pci: OHCI PCI platform driver
04:50 uhci_hcd: USB Universal Host Controller Interface driver
04:50 xhci_hcd 0000:00:14.0: xHCI Host Controller
04:50 xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
04:50 xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0004b810
04:50 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
04:50 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
04:50 usb usb2: Product: xHCI Host Controller
04:50 usb usb2: Manufacturer: Linux 4.13.0-0.rc1.git3.2.fc27.x86_64 xhci-hcd
04:50 usb usb2: SerialNumber: 0000:00:14.0
04:50 hub 2-0:1.0: USB hub found
04:50 hub 2-0:1.0: 9 ports detected
04:50 xhci_hcd 0000:00:14.0: xHCI Host Controller
04:50 xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
04:50 usb usb3: New USB device found, idVendor=1d6b, idProduct=0003
04:50 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
04:50 usb usb3: Product: xHCI Host Controller
04:50 usb usb3: Manufacturer: Linux 4.13.0-0.rc1.git3.2.fc27.x86_64 xhci-hcd
04:50 usb usb3: SerialNumber: 0000:00:14.0
04:50 hub 3-0:1.0: USB hub found
04:50 hub 3-0:1.0: 4 ports detected
04:50 usbcore: registered new interface driver usbserial
04:50 usbcore: registered new interface driver usbserial_generic
04:50 usbserial: USB Serial support registered for generic
04:50 i8042: PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
04:50 serio: i8042 KBD port at 0x60,0x64 irq 1
04:50 serio: i8042 AUX port at 0x60,0x64 irq 12
04:50 mousedev: PS/2 mouse device common for all mice
04:50 rtc_cmos 00:02: RTC can wake from S4
04:50 rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
04:50 rtc_cmos 00:02: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
04:50 device-mapper: uevent: version 1.0.3
04:50 device-mapper: ioctl: 4.36.0-ioctl (2017-06-09) initialised: dm-devel@xxxxxxxxxx
04:50 intel_pstate: Intel P-state driver initializing
04:50 hidraw: raw HID events driver (C) Jiri Kosina
04:50 usbcore: registered new interface driver usbhid
04:50 usbhid: USB HID core driver
04:50 input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
04:50 drop_monitor: Initializing network drop monitor service
04:50 ip_tables: (C) 2000-2006 Netfilter Core Team
04:50 Initializing XFRM netlink socket
04:50 NET: Registered protocol family 10
04:50 Segment Routing with IPv6
04:50 mip6: Mobile IPv6
04:50 NET: Registered protocol family 17
04:50 RAS: Correctable Errors collector initialized.
04:50 microcode: sig=0x40651, pf=0x40, revision=0x20
04:50 microcode: Microcode Update Driver: v2.2.
04:50 AVX2 version of gcm_enc/dec engaged.
04:50 AES CTR mode by8 optimization enabled
04:50 sched_clock: Marking stable (885537102, 0)->(890157704, -4620602)
04:50 registered taskstats version 1
04:50 Loading compiled-in X.509 certificates
04:50 Loaded X.509 cert 'Fedora kernel signing key: f2b7b3c11982a421c0e58e80c1ed66ac68e780f1'
04:50 zswap: loaded using pool lzo/zbud
04:50 Key type big_key registered
04:50 Key type encrypted registered
04:50 Magic number: 9:127:88
04:50 rtc_cmos 00:02: setting system clock to 2017-07-24 17:04:50 UTC (1500915890)
04:50 ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
04:50 ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
04:50 ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
04:50 ata1.00: supports DRM functions and may not be fully accessible
04:50 ata1.00: NCQ Send/Recv Log not supported
04:50 ata1.00: ATA-9: SAMSUNG MZ7TD256HAFV-000L9, DXT02L5Q, max UDMA/133
04:50 ata1.00: 500118192 sectors, multi 1: LBA48 NCQ (depth 31/32), AA
04:50 ata1.00: ACPI cmd f5/00:00:00:00:00:a0 (SECURITY FREEZE LOCK) filtered out
04:50 ata1.00: ACPI cmd ef/10:03:00:00:00:a0 (SET FEATURES) filtered out
04:50 ata1.00: supports DRM functions and may not be fully accessible
04:50 ata1.00: NCQ Send/Recv Log not supported
04:50 ata1.00: configured for UDMA/133
04:50 scsi 0:0:0:0: Direct-Access ATA SAMSUNG MZ7TD256 2L5Q PQ: 0 ANSI: 5
04:50 sd 0:0:0:0: [sda] 500118192 512-byte logical blocks: (256 GB/238 GiB)
04:50 sd 0:0:0:0: [sda] Write Protect is off
04:50 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
04:50 sd 0:0:0:0: Attached scsi generic sg0 type 0
04:50 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
04:50 sd 0:0:0:0: [sda] supports TCG Opal
04:50 sd 0:0:0:0: [sda] Attached SCSI disk
04:50 Freeing unused kernel memory: 2220K
04:50 Write protecting the kernel read-only data: 14336k
04:50 Freeing unused kernel memory: 1408K
04:50 Freeing unused kernel memory: 340K
04:50 x86/mm: Checked W+X mappings: passed, no W+X pages found.
04:50 rodata_test: all tests were successful
04:50 usb 1-1: new high-speed USB device number 2 using ehci-pci
04:50[1]: Starting Create list of required static device nodes for the current kernel...
04:50 usb 2-2: new low-speed USB device number 2 using xhci_hcd
04:50cmdline: Using kernel command line parameters: BOOT_IMAGE=/vmlinuz-4.13.0-0.rc1.git3.2.fc27.x86_64 root=UUID=3756a4b4-a65d-48d3-85e3-286d101cd4b8 ro vconsole.font=latarcyrheb-sun16 rhgb selinux=0 quiet LANG=cs_CZ.UTF-8
04:50 usb 1-1: New USB device found, idVendor=8087, idProduct=8000
04:50 usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
04:50 hub 1-1:1.0: USB hub found
04:50 hub 1-1:1.0: 8 ports detected
04:50 psmouse serio1: synaptics: queried max coordinates: x [..5112], y [..3834]
04:50 audit: type=1130 audit(1500915890.913:10): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
04:50 pps_core: LinuxPPS API ver. 1 registered
04:50 pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@xxxxxxxx>
04:50 psmouse serio1: synaptics: queried min coordinates: x [1024..], y [1024..]
04:50 psmouse serio1: synaptics: Trying to set up SMBus access
04:50 PTP clock support registered
04:50 psmouse serio1: synaptics: SMbus companion is not ready yet
04:50 psmouse serio1: synaptics: quirked min/max coordinates: x [1024..5112], y [2024..4832]
04:50 e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
04:50 e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
04:50 e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode
04:50 usb 2-2: New USB device found, idVendor=17ef, idProduct=6044
04:50 usb 2-2: New USB device strings: Mfr=0, Product=2, SerialNumber=0
04:50 usb 2-2: Product: ThinkPad USB Laser Mouse
04:50 input: ThinkPad USB Laser Mouse as /devices/pci0000:00/0000:00:14.0/usb2/2-2/2-2:1.0/0003:17EF:6044.0001/input/input6
04:50 hid-generic 0003:17EF:6044.0001: input,hidraw0: USB HID v1.11 Mouse [ThinkPad USB Laser Mouse] on usb-0000:00:14.0-2/input0
04:50 psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd002a3/0x940300/0x127c00/0x0, board id: 2668, fw id: 1545510
04:50 psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
04:51 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
04:51 usb 2-4: new high-speed USB device number 3 using xhci_hcd
04:51 usb 1-1.5: new full-speed USB device number 3 using ehci-pci
04:51 e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC clock
04:51 tsc: Refined TSC clocksource calibration: 2693.764 MHz
04:51 clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x26d43bb7f27, max_idle_ns: 440795270902 ns
04:51 e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 28:d2:44:55:53:b1
04:51 e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
04:51 e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: 1000FF-0FF
04:51 [drm] Memory usable by graphics device = 2048M
04:51 [drm] Replacing VGA console driver
04:51 Console: switching to colour dummy device 80x25
04:51 e1000e 0000:00:19.0 enp0s25: renamed from eth0
04:51 [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
04:51 [drm] Driver supports precise vblank timestamp query.
04:51 i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
04:51 usb 1-1.5: New USB device found, idVendor=058f, idProduct=9540
04:51 usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
04:51 usb 1-1.5: Product: EMV Smartcard Reader
04:51 usb 1-1.5: Manufacturer: Generic
04:51 [drm] Initialized i915 1.6.0 20170619 for 0000:00:02.0 on minor 0
04:51 ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
04:51 input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input8
04:51 usb 2-4: New USB device found, idVendor=0bdb, idProduct=193e
04:51 usb 2-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
04:51 usb 2-4: Product: N5321 gw
04:51 usb 2-4: Manufacturer: Lenovo
04:51 usb 2-4: SerialNumber: 07F936FE88D7D0M0
04:51 usb 2-6: new full-speed USB device number 4 using xhci_hcd
04:52 fbcon: inteldrmfb (fb0) is primary device
04:52 usb 2-6: New USB device found, idVendor=138a, idProduct=0017
04:52 usb 2-6: New USB device strings: Mfr=0, Product=0, SerialNumber=1
04:52 usb 2-6: SerialNumber: 2308d4990a85
04:52 psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
04:52 usb 2-7: new full-speed USB device number 5 using xhci_hcd
04:52 input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input7
04:52 usb 2-7: New USB device found, idVendor=8087, idProduct=07dc
04:52 usb 2-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
04:52 usb 2-8: new high-speed USB device number 6 using xhci_hcd
04:52 clocksource: Switched to clocksource tsc
04:52 usb 2-8: New USB device found, idVendor=04f2, idProduct=b39a
04:52 usb 2-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
04:52 usb 2-8: Product: Integrated Camera
04:52 usb 2-8: Manufacturer: SunplusIT INC.
04:52 cdc_wdm 2-4:1.5: cdc-wdm0: USB WDM device
04:52 cdc_wdm 2-4:1.8: cdc-wdm1: USB WDM device
04:52 usbcore: registered new interface driver cdc_wdm
04:52 usbcore: registered new interface driver cdc_ncm
04:52 cdc_mbim 2-4:1.6: cdc-wdm2: USB WDM device
04:52 cdc_mbim 2-4:1.6 wwan0: register 'cdc_mbim' at usb-0000:00:14.0-4, CDC MBIM, fa:b2:b5:84:d0:71
04:52 usbcore: registered new interface driver cdc_mbim
04:52 cdc_mbim 2-4:1.6 wwp0s20u4i6: renamed from wwan0
04:52 Console: switching to colour frame buffer device 240x67
04:52 i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
04:52 EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
04:53 systemd: 15 output lines suppressed due to ratelimiting
04:53 EXT4-fs (sda3): re-mounted. Opts: (null)
04:54 RPC: Registered named UNIX socket transport module.
04:54 RPC: Registered udp transport module.
04:54 RPC: Registered tcp transport module.
04:54 RPC: Registered tcp NFSv4.1 backchannel transport module.
04:54 Installing knfsd (copyright (C) 1996 okir@xxxxxxxxxxxx).
04:54 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
04:54 i801_smbus 0000:00:1f.3: SPD Write Disable is set
04:54 i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
04:54 acpi PNP0C14:01: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
04:54 acpi PNP0C14:02: duplicate WMI GUID 05901221-D566-11D1-B2F0-00A0C9062910 (first instance was on PNP0C14:00)
04:54 tpm_tis 00:05: 1.2 TPM (device-id 0x0, rev-id 78)
04:54 thinkpad_acpi: ThinkPad ACPI Extras v0.25
04:54 thinkpad_acpi: http://ibm-acpi.sf.net/
04:54 thinkpad_acpi: ThinkPad BIOS GJET67WW (2.17 ), EC unknown
04:54 thinkpad_acpi: Lenovo ThinkPad T440s, model 20AQ0069GE
04:54 thinkpad_hwmon thinkpad_hwmon: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info().
04:54 thinkpad_acpi: radio switch found; radios are enabled
04:54 thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
04:54 thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
04:54 thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
04:54 thinkpad_acpi: rfkill switch tpacpi_wwan_sw: radio is unblocked
04:54 tpm tpm0: A TPM error (6) occurred attempting to read a pcr value
04:54 tpm tpm0: TPM is disabled/deactivated (0x6)
04:54 e1000e 0000:00:19.0 em1: renamed from enp0s25
04:54 input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input9
04:54 Bluetooth: Core ver 2.22
04:54 NET: Registered protocol family 31
04:54 Bluetooth: HCI device and connection manager initialized
04:54 Bluetooth: HCI socket layer initialized
04:54 Bluetooth: L2CAP socket layer initialized
04:54 Bluetooth: SCO socket layer initialized
04:54 cdc_acm 2-4:1.1: ttyACM0: USB ACM device
04:54 cdc_acm 2-4:1.3: ttyACM1: USB ACM device
04:54 cdc_acm 2-4:1.9: ttyACM2: USB ACM device
04:54 usbcore: registered new interface driver cdc_acm
04:54 cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
04:54 media: Linux media interface: v0.10
04:54 snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
04:54 input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input12
04:54 input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
04:54 input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input14
04:54 input: HDA Intel HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
04:54 input: HDA Intel HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:03.0/sound/card0/input16
04:54 snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC3232: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
04:54 snd_hda_codec_realtek hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
04:54 snd_hda_codec_realtek hdaudioC1D0: hp_outs=2 (0x16/0x15/0x0/0x0/0x0)
04:54 snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
04:54 snd_hda_codec_realtek hdaudioC1D0: inputs:
04:54 snd_hda_codec_realtek hdaudioC1D0: Dock Mic=0x19
04:54 snd_hda_codec_realtek hdaudioC1D0: Mic=0x1a
04:54 snd_hda_codec_realtek hdaudioC1D0: Internal Mic=0x12
04:54 Linux video capture interface: v2.00
04:54 RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
04:54 RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
04:54 RAPL PMU: hw unit of domain package 2^-14 Joules
04:54 RAPL PMU: hw unit of domain dram 2^-14 Joules
04:54 RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
04:54 Intel(R) Wireless WiFi driver for Linux
04:54 Copyright(c) 2003- 2015 Intel Corporation
04:54 input: HDA Intel PCH Dock Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input17
04:54 input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input18
04:54 input: HDA Intel PCH Dock Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input19
04:54 input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input20
04:54 iTCO_vendor_support: vendor-support=0
04:54 usbcore: registered new interface driver btusb
04:54 Bluetooth: hci0: read Intel version: 370710018002030d56
04:54 Bluetooth: hci0: Intel device is already patched. patch num: 56
04:54 iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
04:54 iTCO_wdt: Found a Lynx Point_LP TCO device (Version=2, TCOBASE=0x1860)
04:54 iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
04:54 iwlwifi 0000:03:00.0: loaded firmware version 17.459231.0 op_mode iwlmvm
04:54 uvcvideo: Found UVC 1.00 device Integrated Camera (04f2:b39a)
04:54 uvcvideo 2-8:1.0: Entity type for entity Extension 4 was not initialized!
04:54 uvcvideo 2-8:1.0: Entity type for entity Extension 3 was not initialized!
04:54 uvcvideo 2-8:1.0: Entity type for entity Processing 2 was not initialized!
04:54 uvcvideo 2-8:1.0: Entity type for entity Camera 1 was not initialized!
04:54 input: Integrated Camera: Integrated C as /devices/pci0000:00/0000:00:14.0/usb2/2-8/2-8:1.0/input/input21
04:54 usbcore: registered new interface driver uvcvideo
04:54 USB Video Class driver (1.1.1)
04:54 iwlwifi 0000:03:00.0: Detected Intel(R) Dual Band Wireless AC 7260, REV=0x144
04:54 iwlwifi 0000:03:00.0: base HW address: 5c:51:4f:e8:e9:28
04:54 intel_rapl: Found RAPL domain package
04:54 intel_rapl: Found RAPL domain core
04:54 intel_rapl: Found RAPL domain uncore
04:54 intel_rapl: Found RAPL domain dram
04:54 Adding 43979772k swap on /dev/sda5. Priority:-1 extents:1 across:43979772k SSFS
04:54 psmouse serio1: synaptics: queried max coordinates: x [..5112], y [..3834]
04:54 psmouse serio1: synaptics: queried min coordinates: x [1024..], y [1024..]
04:54 psmouse serio1: synaptics: Trying to set up SMBus access
04:54 psmouse serio1: synaptics: SMbus companion is not ready yet
04:54 psmouse serio1: synaptics: quirked min/max coordinates: x [1024..5112], y [2024..4832]
04:54 iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
04:54 psmouse serio1: synaptics: Touchpad model: 1, fw: 8.1, id: 0x1e2b1, caps: 0xd002a3/0x940300/0x127c00/0x0, board id: 2668, fw id: 1545510
04:54 psmouse serio1: synaptics: serio: Synaptics pass-through port at isa0060/serio1/input0
04:54 input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input11
04:55 psmouse serio3: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
04:55 EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
04:55 EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
04:55 input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio3/input/input22
04:55 random: crng init done
04:55 Bluetooth: BNEP (Ethernet Emulation) ver 1.3
04:55 Bluetooth: BNEP filters: protocol multicast
04:55 Bluetooth: BNEP socket layer initialized
04:59 ip6_tables: (C) 2000-2006 Netfilter Core Team
05:00 Ebtables v2.0 registered
05:00 nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
05:00 bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
05:01 Netfilter messages via NETLINK v0.30.
05:01 ip_set: protocol 6
05:01 IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
05:01 IPv6: ADDRCONF(NETDEV_UP): em1: link is not ready
05:01 IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
05:01 IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
05:01 IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
05:02 IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
05:03 tun: Universal TUN/TAP device driver, 1.6
05:03 virbr0: port 1(virbr0-nic) entered blocking state
05:03 virbr0: port 1(virbr0-nic) entered disabled state
05:03 device virbr0-nic entered promiscuous mode
05:03 virbr0: port 1(virbr0-nic) entered blocking state
05:03 virbr0: port 1(virbr0-nic) entered listening state
05:03 virbr0: port 1(virbr0-nic) entered disabled state
05:04 IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
05:07 wlp3s0: associated
05:07 IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
05:08 NFSD: starting 90-second grace period (net ffffffff96fde240)
14:14 usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
14:14 usb 3-1: New USB device found, idVendor=1058, idProduct=10a8
14:14 usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
14:14 usb 3-1: Product: Elements 10A8
14:14 usb 3-1: Manufacturer: Western Digital
14:14 usb 3-1: SerialNumber: 5758333145373354504C3031
14:14 usb-storage 3-1:1.0: USB Mass Storage device detected
14:14 scsi host3: usb-storage 3-1:1.0
14:14 usbcore: registered new interface driver usb-storage
14:14 usbcore: registered new interface driver uas
14:15 scsi 3:0:0:0: Direct-Access WD Elements 10A8 1042 PQ: 0 ANSI: 6
14:15 sd 3:0:0:0: Attached scsi generic sg1 type 0
14:15 sd 3:0:0:0: [sdb] Spinning up disk...
14:17 .
14:19 .
14:20 .
14:21 .
14:21 .
14:21 ready
14:21 sd 3:0:0:0: [sdb] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB)
14:21 sd 3:0:0:0: [sdb] Write Protect is off
14:21 sd 3:0:0:0: [sdb] No Caching mode page found
14:21 sd 3:0:0:0: [sdb] Assuming drive cache: write through
14:21 sdb: sdb1 sdb2
14:21 sd 3:0:0:0: [sdb] Attached SCSI disk
14:30 EXT4-fs (sdb2): mounted filesystem with ordered data mode. Opts: (null)
16:32 xhci_hcd 0000:00:14.0: Cannot set link state.
16:32 usb usb3-port1: cannot disable (err = -32)
16:32 usb 3-1: USB disconnect, device number 2

Next message: Andy Shevchenko: "Re: [PATCH v2 2/6] mei: Switch to use new generic UUID API"
Previous message: David Wu: "[PATCH] arm64: dts: rockchip: Add rk3328 io-domain node"
In reply to: Guenter Roeck: "Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4"
Next in thread: Alan Stern: "Re: USB disk speed regression WD Elements - with bisect result 22547c4cc4fe20698a6a85a55b8788859134b8e4"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]