Re: [PATCH v2 12/25] dt-bindings: qcom_nandc: QPIC NAND documentation

[Boris Brezillon]

On Fri, 04 Aug 2017 18:41:20 +0530
Abhishek Sahu <absahu@xxxxxxxxxxxxxx> wrote:

> On 2017-08-04 18:15, Boris Brezillon wrote:
> > On Mon, 31 Jul 2017 21:35:57 +0530
> > Abhishek Sahu <absahu@xxxxxxxxxxxxxx> wrote:
> >   
> >> On 2017-07-26 00:13, Abhishek Sahu wrote:  
> >> > On 2017-07-25 00:47, Rob Herring wrote:  
> >> >> On Wed, Jul 19, 2017 at 05:18:00PM +0530, Abhishek Sahu wrote:  
> >> >>> 1. QPIC NAND will use compatible string "qcom,qpic-nandc-v1.4.0"
> >> >>> 2. QPIC NAND will 3 BAM channels: command, data tx and data rx
> >> >>>    while EBI2 NAND uses only single ADM channel.
> >> >>> 3. CRCI is only required for ADM DMA and its not required for
> >> >>>    QPIC NAND.
> >> >>>
> >> >>> Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
> >> >>> ---
> >> >>>  .../devicetree/bindings/mtd/qcom_nandc.txt         | 54
> >> >>> ++++++++++++++++++++--
> >> >>>  1 file changed, 51 insertions(+), 3 deletions(-)
> >> >>>
> >> >>> diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> >> >>> b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> >> >>> index b24adfe..8efaeb0 100644
> >> >>> --- a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> >> >>> +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
> >> >>> @@ -1,13 +1,15 @@
> >> >>>  * Qualcomm NAND controller
> >> >>>
> >> >>>  Required properties:
> >> >>> -- compatible:		should be "qcom,ebi2-nandc" - EBI2 NAND which uses
> >> >>> ADM
> >> >>> -			DMA like IPQ8064.
> >> >>> -
> >> >>> +- compatible:		must be one of the following:
> >> >>> +	* "qcom,ebi2-nandc" - EBI2 NAND which uses ADM DMA like IPQ8064.
> >> >>> +	* "qcom,qpic-nandc-v1.4.0" - QPIC NAND v1.4.0 which uses BAM DMA
> >> >>> like IPQ4019.  
> >> >>
> >> >> Looks like you have 2 SoCs and 2 versions of h/w. Use SoC specific
> >> >> compatible strings.  
> >> >
> >> >  We have 3 versions of NAND HW currently.
> >> >  EBI2,
> >> >  QPIC version 1.4.0
> >> >  QPIC version 1.5.0
> >> >
> >> >  and multiple Qualcomm SoCs which use any one of these.
> >> >
> >> >  The original plan was to have compatible string for NAND version since
> >> >  same NAND hardware is being in different SoC and SoC dtsi will simply
> >> >  use its NAND version compatible string like other Qualcomm hardwares
> >> >
> >> >
> >> > http://elixir.free-electrons.com/linux/latest/source/Documentation/devicetree/bindings/dma/qcom_bam_dma.txt
> >> >
> >> > http://elixir.free-electrons.com/linux/latest/source/Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
> >> >  
> >> 
> >>   Following are the partial list for NAND controller and supported
> >>   SoC
> >> 
> >>    EBI2:          IPQ8064, APQ8064, MSM7xx, MDM9x15
> >>    QPIC v1.4.0    MDM9x25, MDM9x35, MDM9x45, IPQ4019
> >>    QPIC v1.5.0    MDM9x55, IPQ8074
> >> 
> >>   so could we use NAND controller specific compatible strings instead 
> >> of
> >> SoC
> >>   since it will easy to maintain?  
> > 
> > Nope, though you can re-use the compatible of an old SoC for new SoCs
> > if the IP did not change.
> > 
> > For example:
> > 
> > - EBI2: compatible = "qcom,ipq8064"
> > - QPIC 1.4: compatible = "qcom,mdm9x25"
> > - QPIC 1.5: compatible = "qcom,mdm9x55"
> > 
> > Note that we usually pick the oldest SoC that started embedding an IP
> > when choosing the compatible. So my suggestion assumes IPQ8064 is older
> > than APQ8064, MSM7xx and MDM9x15.  
> 
>   Thanks Boris for detailed clarification.
>   Then I will change the patch to use SoC specific compatible string.
> 
>   Its better to use qcom,ipq4019 for 1.4.0 and qcom,ipq8074 for 1.5.0
>   since we don't have other SoC in upstream and I have tested the
>   NAND driver on these IPQ SoC's.

Sounds good, but I'll let Rob confirm.