Re: [PATCH v3 05/11] net: stmmac: dwmac-rk: Add internal phy support
From: Corentin Labbe
Date: Wed Aug 09 2017 - 04:45:54 EST
On Thu, Aug 03, 2017 at 07:06:33PM +0800, Chen-Yu Tsai wrote:
> On Thu, Aug 3, 2017 at 1:38 AM, Florian Fainelli <f.fainelli@xxxxxxxxx> wrote:
> > On 08/01/2017 11:21 PM, David Wu wrote:
> >> To make internal phy work, need to configure the phy_clock,
> >> phy cru_reset and related registers.
> >>
> >> Signed-off-by: David Wu <david.wu@xxxxxxxxxxxxxx>
> >> ---
> >> .../devicetree/bindings/net/rockchip-dwmac.txt | 6 +-
> >> drivers/net/ethernet/stmicro/stmmac/dwmac-rk.c | 81 ++++++++++++++++++++++
> >> 2 files changed, 86 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> >> index 8f42755..ec39b31 100644
> >> --- a/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> >> +++ b/Documentation/devicetree/bindings/net/rockchip-dwmac.txt
> >> @@ -25,7 +25,8 @@ Required properties:
> >> - clock-names: One name for each entry in the clocks property.
> >> - phy-mode: See ethernet.txt file in the same directory.
> >> - pinctrl-names: Names corresponding to the numbered pinctrl states.
> >> - - pinctrl-0: pin-control mode. can be <&rgmii_pins> or <&rmii_pins>.
> >> + - pinctrl-0: pin-control mode. can be <&rgmii_pins>, <&rmii_pins> or led pins
> >> + for internal phy mode.
> >> - clock_in_out: For RGMII, it must be "input", means main clock(125MHz)
> >> is not sourced from SoC's PLL, but input from PHY; For RMII, "input" means
> >> PHY provides the reference clock(50MHz), "output" means GMAC provides the
> >> @@ -40,6 +41,9 @@ Optional properties:
> >> - tx_delay: Delay value for TXD timing. Range value is 0~0x7F, 0x30 as default.
> >> - rx_delay: Delay value for RXD timing. Range value is 0~0x7F, 0x10 as default.
> >> - phy-supply: phandle to a regulator if the PHY needs one
> >> + - clocks: <&cru MAC_PHY>: Clock selector for internal macphy
> >> + - phy-is-internal: A boolean property allows us to know that MAC will connect to
> >> + internal phy.
> >
> > This is incorrect in two ways:
> >
> > - this is a property of the PHY, so it should be documented as such in
> > Documentation/devicetree/bindings/net/phy.txt so other bindings can
> > re-use it
> >
> > - if it was specific to your MAC you would expect a vendor prefix to
> > this property, which is not there
> >
> > An alternative way to implement the external/internal logic selection
> > would be mandate that your Ethernet PHY node have a compatible string
> > like this:
> >
> > phy@0 {
> > compatible = "ethernet-phy-id1234.d400", "ethernet-phy-802.3-c22";
> > };
> >
> > Then you don't need this phy-is-internal property, because you can
> > locate the PHY node by the phy-handle (see more about that in a reply to
> > patch 10) and you can determine ahead of time whether this PHY is
> > internal or not based on its compatible string.
>
> This doesn't really work for us (sunxi). The "internal" PHY of the H3
> is also available in the X-Powers AC200 combo chip, which would be
> external. Same ID. So if someone were to be stupid and put the two
> together, you wouldn't know which one it actually is. Generically
> it doesn't make sense to match against the ID either. The PHY is
> only integrated or inlined into the SoC, meaning it could be moved
> elsewhere or even be a discreet part.
>
> The way I see it is more like a reversed pinmux. The system should
> select either the internal set or external set of xMII pins to use.
>
> A phy-is-internal property in the PHY node would work for us. We
> already need a PHY node to describe its clocks and resets.
>
> A side note to this solution is that, since the internal PHY is defined
> at the .dtsi level, any external PHYs at the same address would need to
> make sure to delete the property, which is kind of counterintuitive, but
> it is how device tree works. One would want to put the internal PHY's
> address, assuming it is configurable, on something that is rarely used.
>
Hello David, Florian, Andrew
Could someone ack this ? or nack if you think that the chance for having two PHY id both internal and external is too low.
Anyway, we need a choice.
Regards