Re: [PATCH v4 08/20] mtd: nand: qcom: support for passing flags in transfer functions

From: Abhishek Sahu
Date: Wed Aug 16 2017 - 03:23:44 EST

Next message: Kefeng Wang: "[PATCH] mtd: nand: convert to unified device property interface"
Previous message: Reizer, Eyal: "RE: [v7 wlcore: add missing nvs file name info for wilink8"
In reply to: Archit Taneja: "Re: [PATCH v4 08/20] mtd: nand: qcom: support for passing flags in transfer functions"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On 2017-08-16 09:48, Archit Taneja wrote:

On 08/11/2017 05:09 PM, Abhishek Sahu wrote:

The BAM has multiple flags to control the transfer. This patch
adds flags parameter in register and data transfer functions and
modifies all these functions call with appropriate flags using
following rule

1. Read and write canât go in single command descriptor so
separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
All write request will modify the data in internal buffer and
this buffer will be flushed to NAND device once EOT flag is set.
So for all the write requests in single codeword, the EOT should
be cleared for all tx data descriptors except the last one.

Signed-off-by: Abhishek Sahu <absahu@xxxxxxxxxxxxxx>
---
drivers/mtd/nand/qcom_nandc.c | 122 ++++++++++++++++++++++++------------------
1 file changed, 70 insertions(+), 52 deletions(-)

diff --git a/drivers/mtd/nand/qcom_nandc.c b/drivers/mtd/nand/qcom_nandc.c
index f52a692..d9c8a6b 100644
--- a/drivers/mtd/nand/qcom_nandc.c
+++ b/drivers/mtd/nand/qcom_nandc.c
@@ -180,6 +180,14 @@
#define QPIC_PER_CW_CMD_SGL 32
#define QPIC_PER_CW_DATA_SGL 8
+/* Flags used for BAM DMA desc preparation*/

We can remove BAM from here since later on
we will pass flag for erase code word and it will
be used by ADM also.

+/* Don't set the EOT in current tx sgl */
+#define NAND_BAM_NO_EOT BIT(0)
+/* Set the NWD flag in current sgl */
+#define NAND_BAM_NWD BIT(1)
+/* Finish writing in the current sgl and start writing in another sgl */
+#define NAND_BAM_NEXT_SGL BIT(2)
+
/*
* This data type corresponds to the BAM transaction which will be used for all
* NAND transfers.
@@ -731,7 +739,7 @@ static int prep_adm_dma_desc(struct qcom_nand_controller *nandc, bool read,
* @num_regs: number of registers to read

Minor comment: the read_reg_dma/write_reg/read_data/write_data_dma
funcs add a new arg, so it
would be nice to update the comment describing the function and its
arguments. It would also

Thanks. I will update the comment to include this new arg.

be nice to mention that the flags are presently used only for
controllers using BAM.

We can use this flag for ADM also so I will make the
comment generic.

With that,

Reviewed-by: Archit Taneja <architt@xxxxxxxxxxxxxx>

Thanks,
Archit

*/
static int read_reg_dma(struct qcom_nand_controller *nandc, int first,
- int num_regs)
+ int num_regs, unsigned int flags)
{
bool flow_control = false;
void *vaddr;
@@ -755,7 +763,7 @@ static int read_reg_dma(struct qcom_nand_controller *nandc, int first,
* @num_regs: number of registers to write
*/
static int write_reg_dma(struct qcom_nand_controller *nandc, int first,
- int num_regs)
+ int num_regs, unsigned int flags)
{
bool flow_control = false;
struct nandc_regs *regs = nandc->regs;
@@ -767,6 +775,9 @@ static int write_reg_dma(struct qcom_nand_controller *nandc, int first,
if (first == NAND_FLASH_CMD)
flow_control = true;
+ if (first == NAND_EXEC_CMD)
+ flags |= NAND_BAM_NWD;
+
if (first == NAND_DEV_CMD1_RESTORE)
first = NAND_DEV_CMD1;
@@ -788,7 +799,7 @@ static int write_reg_dma(struct qcom_nand_controller *nandc, int first,
* @size: DMA transaction size in bytes
*/
static int read_data_dma(struct qcom_nand_controller *nandc, int reg_off,
- const u8 *vaddr, int size)
+ const u8 *vaddr, int size, unsigned int flags)
{
return prep_adm_dma_desc(nandc, true, reg_off, vaddr, size, false);
}
@@ -802,7 +813,7 @@ static int read_data_dma(struct qcom_nand_controller *nandc, int reg_off,
* @size: DMA transaction size in bytes
*/
static int write_data_dma(struct qcom_nand_controller *nandc, int reg_off,
- const u8 *vaddr, int size)
+ const u8 *vaddr, int size, unsigned int flags)
{
return prep_adm_dma_desc(nandc, false, reg_off, vaddr, size, false);
}
@@ -813,9 +824,9 @@ static int write_data_dma(struct qcom_nand_controller *nandc, int reg_off,
*/
static void config_nand_page_read(struct qcom_nand_controller *nandc)
{
- write_reg_dma(nandc, NAND_ADDR0, 2);
- write_reg_dma(nandc, NAND_DEV0_CFG0, 3);
- write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1);
+ write_reg_dma(nandc, NAND_ADDR0, 2, 0);
+ write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
+ write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1, 0);
}
/*
@@ -824,11 +835,12 @@ static void config_nand_page_read(struct qcom_nand_controller *nandc)
*/
static void config_nand_cw_read(struct qcom_nand_controller *nandc)
{
- write_reg_dma(nandc, NAND_FLASH_CMD, 1);
- write_reg_dma(nandc, NAND_EXEC_CMD, 1);
+ write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
- read_reg_dma(nandc, NAND_FLASH_STATUS, 2);
- read_reg_dma(nandc, NAND_ERASED_CW_DETECT_STATUS, 1);
+ read_reg_dma(nandc, NAND_FLASH_STATUS, 2, 0);
+ read_reg_dma(nandc, NAND_ERASED_CW_DETECT_STATUS, 1,
+ NAND_BAM_NEXT_SGL);
}
/*
@@ -847,9 +859,10 @@ static void config_nand_single_cw_page_read(struct qcom_nand_controller *nandc)
*/
static void config_nand_page_write(struct qcom_nand_controller *nandc)
{
- write_reg_dma(nandc, NAND_ADDR0, 2);
- write_reg_dma(nandc, NAND_DEV0_CFG0, 3);
- write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1);
+ write_reg_dma(nandc, NAND_ADDR0, 2, 0);
+ write_reg_dma(nandc, NAND_DEV0_CFG0, 3, 0);
+ write_reg_dma(nandc, NAND_EBI2_ECC_BUF_CFG, 1,
+ NAND_BAM_NEXT_SGL);
}
/*
@@ -858,13 +871,13 @@ static void config_nand_page_write(struct qcom_nand_controller *nandc)
*/
static void config_nand_cw_write(struct qcom_nand_controller *nandc)
{
- write_reg_dma(nandc, NAND_FLASH_CMD, 1);
- write_reg_dma(nandc, NAND_EXEC_CMD, 1);
+ write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
- read_reg_dma(nandc, NAND_FLASH_STATUS, 1);
+ read_reg_dma(nandc, NAND_FLASH_STATUS, 1, NAND_BAM_NEXT_SGL);
- write_reg_dma(nandc, NAND_FLASH_STATUS, 1);
- write_reg_dma(nandc, NAND_READ_STATUS, 1);
+ write_reg_dma(nandc, NAND_FLASH_STATUS, 1, 0);
+ write_reg_dma(nandc, NAND_READ_STATUS, 1, NAND_BAM_NEXT_SGL);
}
/*
@@ -911,8 +924,8 @@ static int nandc_param(struct qcom_nand_host *host)
nandc_set_reg(nandc, NAND_DEV_CMD1_RESTORE, nandc->cmd1);
nandc_set_reg(nandc, NAND_DEV_CMD_VLD_RESTORE, nandc->vld);
- write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1);
- write_reg_dma(nandc, NAND_DEV_CMD1, 1);
+ write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1, 0);
+ write_reg_dma(nandc, NAND_DEV_CMD1, 1, NAND_BAM_NEXT_SGL);
nandc->buf_count = 512;
memset(nandc->data_buffer, 0xff, nandc->buf_count);
@@ -920,11 +933,11 @@ static int nandc_param(struct qcom_nand_host *host)
config_nand_single_cw_page_read(nandc);
read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer,
- nandc->buf_count);
+ nandc->buf_count, 0);
/* restore CMD1 and VLD regs */
- write_reg_dma(nandc, NAND_DEV_CMD1_RESTORE, 1);
- write_reg_dma(nandc, NAND_DEV_CMD_VLD_RESTORE, 1);
+ write_reg_dma(nandc, NAND_DEV_CMD1_RESTORE, 1, 0);
+ write_reg_dma(nandc, NAND_DEV_CMD_VLD_RESTORE, 1, NAND_BAM_NEXT_SGL);
return 0;
}
@@ -946,14 +959,14 @@ static int erase_block(struct qcom_nand_host *host, int page_addr)
nandc_set_reg(nandc, NAND_FLASH_STATUS, host->clrflashstatus);
nandc_set_reg(nandc, NAND_READ_STATUS, host->clrreadstatus);
- write_reg_dma(nandc, NAND_FLASH_CMD, 3);
- write_reg_dma(nandc, NAND_DEV0_CFG0, 2);
- write_reg_dma(nandc, NAND_EXEC_CMD, 1);
+ write_reg_dma(nandc, NAND_FLASH_CMD, 3, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_DEV0_CFG0, 2, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
- read_reg_dma(nandc, NAND_FLASH_STATUS, 1);
+ read_reg_dma(nandc, NAND_FLASH_STATUS, 1, NAND_BAM_NEXT_SGL);
- write_reg_dma(nandc, NAND_FLASH_STATUS, 1);
- write_reg_dma(nandc, NAND_READ_STATUS, 1);
+ write_reg_dma(nandc, NAND_FLASH_STATUS, 1, 0);
+ write_reg_dma(nandc, NAND_READ_STATUS, 1, NAND_BAM_NEXT_SGL);
return 0;
}
@@ -973,10 +986,10 @@ static int read_id(struct qcom_nand_host *host, int column)
nandc_set_reg(nandc, NAND_FLASH_CHIP_SELECT, DM_EN);
nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
- write_reg_dma(nandc, NAND_FLASH_CMD, 4);
- write_reg_dma(nandc, NAND_EXEC_CMD, 1);
+ write_reg_dma(nandc, NAND_FLASH_CMD, 4, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
- read_reg_dma(nandc, NAND_READ_ID, 1);
+ read_reg_dma(nandc, NAND_READ_ID, 1, NAND_BAM_NEXT_SGL);
return 0;
}
@@ -990,10 +1003,10 @@ static int reset(struct qcom_nand_host *host)
nandc_set_reg(nandc, NAND_FLASH_CMD, RESET_DEVICE);
nandc_set_reg(nandc, NAND_EXEC_CMD, 1);
- write_reg_dma(nandc, NAND_FLASH_CMD, 1);
- write_reg_dma(nandc, NAND_EXEC_CMD, 1);
+ write_reg_dma(nandc, NAND_FLASH_CMD, 1, NAND_BAM_NEXT_SGL);
+ write_reg_dma(nandc, NAND_EXEC_CMD, 1, NAND_BAM_NEXT_SGL);
- read_reg_dma(nandc, NAND_FLASH_STATUS, 1);
+ read_reg_dma(nandc, NAND_FLASH_STATUS, 1, NAND_BAM_NEXT_SGL);
return 0;
}
@@ -1389,7 +1402,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
if (data_buf)
read_data_dma(nandc, FLASH_BUF_ACC, data_buf,
- data_size);
+ data_size, 0);
/*
* when ecc is enabled, the controller doesn't read the real
@@ -1405,7 +1418,7 @@ static int read_page_ecc(struct qcom_nand_host *host, u8 *data_buf,
*oob_buf++ = 0xff;
read_data_dma(nandc, FLASH_BUF_ACC + data_size,
- oob_buf, oob_size);
+ oob_buf, oob_size, 0);
}
if (data_buf)
@@ -1447,7 +1460,7 @@ static int copy_last_cw(struct qcom_nand_host *host, int page)
config_nand_single_cw_page_read(nandc);
- read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, size);
+ read_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, size, 0);
ret = submit_descs(nandc);
if (ret)
@@ -1516,19 +1529,19 @@ static int qcom_nandc_read_page_raw(struct mtd_info *mtd,
config_nand_cw_read(nandc);
- read_data_dma(nandc, reg_off, data_buf, data_size1);
+ read_data_dma(nandc, reg_off, data_buf, data_size1, 0);
reg_off += data_size1;
data_buf += data_size1;
- read_data_dma(nandc, reg_off, oob_buf, oob_size1);
+ read_data_dma(nandc, reg_off, oob_buf, oob_size1, 0);
reg_off += oob_size1;
oob_buf += oob_size1;
- read_data_dma(nandc, reg_off, data_buf, data_size2);
+ read_data_dma(nandc, reg_off, data_buf, data_size2, 0);
reg_off += data_size2;
data_buf += data_size2;
- read_data_dma(nandc, reg_off, oob_buf, oob_size2);
+ read_data_dma(nandc, reg_off, oob_buf, oob_size2, 0);
oob_buf += oob_size2;
}
@@ -1595,7 +1608,8 @@ static int qcom_nandc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
}
- write_data_dma(nandc, FLASH_BUF_ACC, data_buf, data_size);
+ write_data_dma(nandc, FLASH_BUF_ACC, data_buf, data_size,
+ i == (ecc->steps - 1) ? NAND_BAM_NO_EOT : 0);
/*
* when ECC is enabled, we don't really need to write anything
@@ -1608,7 +1622,7 @@ static int qcom_nandc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
oob_buf += host->bbm_size;
write_data_dma(nandc, FLASH_BUF_ACC + data_size,
- oob_buf, oob_size);
+ oob_buf, oob_size, 0);
}
config_nand_cw_write(nandc);
@@ -1663,19 +1677,22 @@ static int qcom_nandc_write_page_raw(struct mtd_info *mtd,
oob_size2 = host->ecc_bytes_hw + host->spare_bytes;
}
- write_data_dma(nandc, reg_off, data_buf, data_size1);
+ write_data_dma(nandc, reg_off, data_buf, data_size1,
+ NAND_BAM_NO_EOT);
reg_off += data_size1;
data_buf += data_size1;
- write_data_dma(nandc, reg_off, oob_buf, oob_size1);
+ write_data_dma(nandc, reg_off, oob_buf, oob_size1,
+ NAND_BAM_NO_EOT);
reg_off += oob_size1;
oob_buf += oob_size1;
- write_data_dma(nandc, reg_off, data_buf, data_size2);
+ write_data_dma(nandc, reg_off, data_buf, data_size2,
+ NAND_BAM_NO_EOT);
reg_off += data_size2;
data_buf += data_size2;
- write_data_dma(nandc, reg_off, oob_buf, oob_size2);
+ write_data_dma(nandc, reg_off, oob_buf, oob_size2, 0);
oob_buf += oob_size2;
config_nand_cw_write(nandc);
@@ -1729,8 +1746,8 @@ static int qcom_nandc_write_oob(struct mtd_info *mtd, struct nand_chip *chip,
update_rw_regs(host, 1, false);
config_nand_page_write(nandc);
- write_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer,
- data_size + oob_size);
+ write_data_dma(nandc, FLASH_BUF_ACC,
+ nandc->data_buffer, data_size + oob_size, 0);
config_nand_cw_write(nandc);
ret = submit_descs(nandc);
@@ -1814,7 +1831,8 @@ static int qcom_nandc_block_markbad(struct mtd_info *mtd, loff_t ofs)
update_rw_regs(host, 1, false);
config_nand_page_write(nandc);
- write_data_dma(nandc, FLASH_BUF_ACC, nandc->data_buffer, host->cw_size);
+ write_data_dma(nandc, FLASH_BUF_ACC,
+ nandc->data_buffer, host->cw_size, 0);
config_nand_cw_write(nandc);
ret = submit_descs(nandc);

Next message: Kefeng Wang: "[PATCH] mtd: nand: convert to unified device property interface"
Previous message: Reizer, Eyal: "RE: [v7 wlcore: add missing nvs file name info for wilink8"
In reply to: Archit Taneja: "Re: [PATCH v4 08/20] mtd: nand: qcom: support for passing flags in transfer functions"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]